Rinnai RHFE-431WTA installation manual Sleeve and Manifold Installation, Method for Standard Walls

Page 21

SLEEVE AND MANIFOLD INSTALLATION

METHOD FOR STANDARD WALLS

1. Disassemble Manifold from Sleeve.

The flue consists of 3 parts, sleeve, inside connectors and tube, outside terminal; (dis-assembly by pulling hard on outside terminal and inner connections, then pull sleeve off outer terminal.)

NOTE: Clearance to combustibles for terminal assembly sleeve and flanges is 0".

2. Adjustment of Sleeve Length.

Measure wall thickness through previously drilled 3 1/8 (80mm) hole.

End of sleeve should protrude 3/16"3/8" (510mm) from outside wall. Adjust sleeve length to wall thickness plus 3/16"3/8" (510mm). (Sleeve is threaded for adjustment.) Do not extend beyond red line.

3. For S and A flue only.

Depending on flue set and wall thickness extension piece “C” may need to be removed.

Cut plastic, remove extension, then follow instruction 2. This applies to “S” and “A” flues only.

There is no extension on other flues, they can be fully adjusted by turning the threaded section.

4. Fixing Sleeve.

Fix to the wall, using the 3 screws provided.

NOTE: The flange is marked “TOP”, sleeve must be fitted with this mark Up. Check sleeve protrudes 3/16" 3/8" (510mm) on the outside.

Flanges

Connection Sleeve Terminal

Do not extend beyond red line

Extension joint

Extension

under plastic

("S" and "A" flues only)

Adjust length by turning sleeve.

A BC

 

Remove extension at this

"A" Flue only

point it necessary.

5-10mm

"TOP"

° 2

Fixing Screw

Don't remove green plastic covering from sleeve.

– 19 –

Page 20 Page 22
Image 21
Page 20 Page 22
Contents RHFE-431WTA Table of Contents Safety Devices Features of the RHFE-431WTA UnitsTechnical Data GAS Conversion SpecificationsIncluded in Carton Page General Information DimensionsSpecifications SpecificationsAIR Supply Safety Points Gasoline Getting to Know Your NEW RHFE-431 Temperatures Mode OperationControl Panel LED DisplayCUT-AWAY Diagram Page Installation Instructions GAS Connection Flue Manifold Position Secure Heater to WallWall Mounting Brackets Windowordoorthatmaybeopened Vent Termination ClearancesFlue Sizes Location / ClearancesStandard Installation of Flue Manifold Snow AreasFIT Back Covers Sides only Method for Standard Walls Sleeve and Manifold InstallationProvided to compensate for weather board angle Fitting Unit AIR Inlet HoseLocking Clamp Screw Clamp and Insulation Instruct Customer on USE of Heater Operating Instructions Setting the Clock Setting the Current Time & DAYTo Open the Control Panel Operating the Heater Manually To turn the heater onTo turn the heater OFF OFF 3 4 OFF Auto Frost Man Override Select Progr Clock Temp R Programing the Weekly TimersExample Schedule Programing the Timers ExampleTimers Programing the Timers ExampleWeekly Timer Review Function To enter the Weekly Timer Review modeTo exit the Weekly Timer Review mode Points to remember when writing your program Your Weekly Timer ProgramFactory PRE-SET Program Points to consider before writing your programOperating the Timers Returning to Manual ModeFollow the steps below to operate the timers Override Function If the current timerTo turn on the Override function Period is on heating Period is OFFTo turn off the Frost Protection Frost ProtectionTo turn on the Economy mode Energy Saving ModeTo turn off the Economy Mode Economy Mode InformationFunction Lock To activate the Function LockTo deactivate the Function Lock Fault-Failure Procedure Testing UnitWhen the unit is turned off PRE-SERVICE CheckAt Ignition During CombustionTrouble Shooting Code Displayed Fault Remedy Error MessagesMaintenance Suggestions Maintenance / ServiceWiring Diagram Consumer Support Warranty InformationHeat Exchanger Year of Failure Allowance Schematic Diagram Page Page Page Page Parts List Page Page Page Part Name QTY Remarks Flow Diagram Rank Parts Name Parts no QTY Remarks Vent KIT Names and Numbers of Parts How to connect exhaust pipes Installing AN Extension KITHow to connect air intake hose Maximum extendable lengthTo prevent water condensation Qualified Installing Agency Page 431F-1720×0800 2008.09

RHFE-431WTA specifications

The Rinnai RHFE-431WTA is a sophisticated gas heater designed to provide efficient and reliable warmth for residential spaces. This innovative heating solution combines advanced technologies with user-friendly features, making it an ideal choice for homeowners seeking comfort without compromising on energy efficiency.

One of the standout characteristics of the RHFE-431WTA is its sleek, compact design. This gas heater can be easily integrated into any room, thanks to its modern aesthetics and low-profile build. Its dimensions allow it to fit snugly into various interior layouts, ensuring that it occupies minimal space while delivering maximum heat output.

A key feature of the RHFE-431WTA is its impressive heating capacity. With the ability to produce up to 4.2 kilowatts of heat, this unit can effectively warm spaces of various sizes. Whether it’s a cozy living area or a larger family room, the heater can adapt to your needs, providing comfortable temperatures even in the coldest months.

The Rinnai RHFE-431WTA also boasts advanced fan technology that distributes heat evenly throughout the room, eliminating cold spots and ensuring consistent warmth. Its whisper-quiet operation enhances the user experience, allowing you to enjoy a tranquil environment without the distraction of noisy heating equipment.

Energy efficiency is another major highlight of the RHFE-431WTA. This unit features a high energy efficiency rating, which not only reduces utility costs but also minimizes environmental impact. Its advanced combustion technology ensures that gas is burned optimally, contributing to lower emissions and a more sustainable heating solution.

The heater also includes an intelligent control system. With a user-friendly interface, homeowners can easily adjust settings to suit their comfort preferences. The unit comes equipped with a digital display that provides real-time information on temperature settings, operation modes, and timers, allowing for precise control over your heating needs.

Safety is a top priority for Rinnai, and the RHFE-431WTA is no exception. The heater is equipped with multiple safety features, including an automatic shut-off mechanism that activates if it detects any irregularities during operation. This ensures peace of mind for users, particularly in households with children or pets.

In summary, the Rinnai RHFE-431WTA gas heater stands out for its efficiency, advanced features, and stylish design. Whether you're looking to enhance comfort in your home or reduce energy consumption, this heater delivers on all fronts, making it a top choice in the market.
Top Page Image Contents