Insert Vent Connection

NOTE: Connect the supplied 3' of stainless steel flexliner to the exhaust liner (already attached to the terminal) using the coupler (also supplied). Secure and seal before dropping down the chim- ney.

FIGURE 2

Move the insert close to its final position inside the wood- burning fireplace. This unit is equipped with 6 levelling screws located as follows: two are on either side of the circulation blower on the rear panel; four are located front and back on either side beneath the log support. Level using four of the levelling screws. See Figure 1a. Levelling the unit will eliminate rocking or excessive noise when the fan is in operation. Once the unit is level, move it partially into place within the fireplace to allow for all connections to be made. It is not practical to level the insert once it has been installed. Determine the required depth prior to in- stalling the unit and adjust the four levelling screws accord- ingly.

CHIMNEY CONNECTION

Chimney installation must conform to both national and local code requirements. The chimney must be lined with one 2" or 3" diameter liner for intake and one 3" diameter liner for exhaust. The minimum and maximum vent lengths are 10 and 35 feet respectively. Recommended Napoleon kits come in 3 lengths:

1-2" & 1-3" DOUBLE PLY ALUMINUM LINER-INLET AND EXHAUST &

2-3" TO 2" REDUCER:

GDI-2320KT	VENT KIT 20FT
GDI-2325KT	VENT KIT 25FT
GDI-2335KT	VENT KIT 35FT
2-3" DOUBLE PLY ALUMINUM LINER-INLET AND EXHAUST:
GDI-320KT	VENT KIT 20FT
GDI-325KT	VENT KIT 25 FT
GDI-335KT	VENT KIT 35 FT

While the liners must be continuous from the fireplace to the chimney cap, to achieve the needed length, they may be coupled, using an aluminium coupler, provided installation is sealed & secured.

We recommend that exhaust vents that pass through unheated spaces, such as a garage or attic, be wrapped in a protective sleeve to minimize condensa- tion and reverse flow symptoms.

This unit is approved for use with a 2" liner for air intake and a 3" liner for exhaust. For best performance, however, it is recommended to use two 3" liners.

If a 2" liner is used for the intake, it is necessary to

adjust the primary air shutter. See "Air Shutter Settings". 1. OUTSIDE: Slip the

one end of a liner a

2.Gently stretch the liners to the required lengths and in- sert into the chimney. Place the terminal onto the top of the chimney cap and fit the flashing plate to suit. Make weather tight by sealing with caulking (not supplied) and fasten to the chimney with screws and plugs (not supplied).

3.NOTE: If there is not enough ceiling height between the fireplace and the insert to allow the flexliner connection on the top of the unit to be made, proceed to step 4.

If there is enough ceiling height, connect the 3" stainless steel flexliner to the exhaust collar closest to the top front on the unit. See figure 1c. Connect the intake flexliner to the remaining rear collar. Secure and seal.

FIGURE 4

BACK WALL

LOG SUPPORT

FIGURE 5

4.Both the log support and the back wall must be removed in order to gain access to the vent connection assembly. Both the back wall and log support are detached by remov- ing the 12 perimeter screws of the back wall and the 3 screws located at the back of the log support. Remove the vent connection assembly.

NOTE: The vent connection assembly collars are not spe- cific until the stainless steel flexliner has been attached to one side. This now designates the side as exhaust. The exhaust collar must be positioned closest to the front open- ing of the insert. SEE FIGURE 1c. Secure and seal the flexliners.

minimum of 2" over the collar of the air terminal. Secure using 3 screws. Then seal the joint and screw heads with high temperature sealant. Repeat with the other liner to the exhaust collar of the terminal.

ALUMINUM

FLEXLINER

COUPLER

STAINLESS

STEEL

FLEXLINER

FIGURE 3

5.To reinstall the vent connection assembly, reach in through the in- sert and manoeuvre the vent con- nection assembly through the opening in the firebox top. Take care not to damage the gasket. Secure the assembly using the four studs and ¼-20 hex nuts.

FIGURE 6

VENT CONNECTION

ASSEMBLY

W415-0314 / C / 01.15.04

GDI-44N, GDI-44P specifications

Napoleon Grills has long been a trusted name in outdoor cooking, and their GDI-44P and GDI-44N models exemplify the brand's commitment to quality, performance, and innovation. These gas grills cater to both novice cooks and seasoned grill masters, making outdoor cooking accessible and enjoyable for everyone.

One of the standout features of the GDI-44P and GDI-44N is their impressive cooking surface. With a total cooking area of 825 square inches, these grills can accommodate a variety of dishes simultaneously, making them perfect for large gatherings and family barbecues. The primary cooking area is 644 square inches, providing ample space for grilling burgers, steaks, and veggies, while the secondary cooking area allows for indirect cooking or warming previously grilled items.

Equipped with Napoleon's innovative i-GLOW backlit control knobs, the GDI-44P and GDI-44N ensure visibility during nighttime grilling sessions. This feature not only enhances safety but also adds a stylish touch to the grill’s overall design. Additionally, the LED lights illuminate the cooking surface, allowing for precision cooking even after the sun goes down.

Both models utilize a powerful 44,000 BTU stainless steel burner system that delivers even heat distribution across the grill. The patented wave-shaped grill grates provide exceptional heat retention and sear marks, ensuring that food is cooked to perfection every time. The grills also include a rear infrared burner, ideal for rotisserie cooking, which complements the main grilling area by allowing cooks to prepare a whole chicken, roast, or other large cuts of meat with ease.

Durability is key in the construction of the GDI-44P and GDI-44N. Both grills feature a heavy-duty stainless steel body, which is resistant to corrosion and designed to withstand the elements year-round. The spacious side shelves provide additional prep space and come with integrated tool hooks for convenient access to grilling tools.

In terms of user-friendly technology, both grills feature an easy-to-use ignition system for reliable starts every time. The built-in temperature gauge allows for easy monitoring of cooking temperatures, ensuring perfectly grilled dishes.

In conclusion, the Napoleon Grills GDI-44P and GDI-44N are exemplary models that combine functionality, durability, and style. With their generous cooking space, advanced features, and reliable performance, they represent an excellent investment for anyone looking to enhance their outdoor cooking experience. Whether grilling for a large crowd or a family dinner, these grills deliver exceptional results, making them a worthy addition to any outdoor kitchen.