Installation Instructions, MAY Result | Halsey Taylor HRFG

HRFG - ERA HRFG - SRA HRFG - SER*A

INSTALLATION INSTRUCTIONS

1.Install remote chiller. Remove front panel of chiller. Remove and discard cardboard inner pack from be tween compressor and side panel. Slide chiller onto the shelf and position it to the left within the guides on the shelf.

NOTE: Building construction must allow for adequate air flow on both sides, top, and back of chiller. A minimum of 4" (102mm) on both sides and top is required. See chiller instructions for additional instructions.

2.Make water supply connections. Attach an unplated copper water inlet line and a service stop (not provided) to the chiller. Inlet port is marked on the chiller (3/8" O.D. copper tube). Bend the copper tube (provided) at an appropriate length from chiller to opening in frame. Install a 3/8" O.D. tube tee fitting (pro vided) on the marked chiller outlet port. Turn on the water supply and flush the line thoroughly.

3.Hang the upper panel on the mounting frame hanger. Align holes in the panel with the holes in the mounting frame. Be sure that panel is engaged with hanger at top of frame before releasing it.

4.Install fountain. Remove access cover plate on underside of fountains and save the screws. Mount the fountains to the upper panel and the wall frame with (4) 5/16" x 1-1/4" (32mm) long bolts, washers, and nuts. Tighten securely, but do not overtighten. Over tightening will crack the Marblyte Fountain.

NOTE: The short fountain should be mounted to the upper left hand side of the panel.

5.Remove elbow from end of p-trap and attach it to drain tube. Re-attach elbow to p-trap and cut waste tube to required length using plumbing hardware and trap as a guide.

6.Make connection between remote chiller outlet tube and fountain strainer. Insert the water inlet line into inlet side of strainer by pushing it in until it reaches a positive stop, approximately 3/4" (19mm). Turn on water supply and check for leaks. Newly installed water supply line should be insulated after leak check is completed. DO NOT SOLDER TUBES INSERTED INTO THE STRAINER AS DAMAGE TO THE O-RINGS

MAY RESULT.

7.These products are designed to operate on 20-105 PSIG supply line pressure. If inlet pressure is above 105 PSIG, a pressure regulator must be installed in the supply line. Any damage caused by reason of connecting these products to supply line pressures lower than 20 PSIG or higher than 105 PSIG is not covered by warranty.

8.Make electrical connections to the chiller. See chiller instructions.

9.Check stream height from bubbler. Stream height is factory set at 45-50 PSI. If supply pressure varies greatly from this, remove items 5 & 13 (See Figure 6, Page 6) by loosening set screw (item 10) and adjust the screw on regulator (item 9). Clockwise adjustment will raise stream height and counter-clockwise adjustment will lower stream height. For best adjustment stream height should be approximately 1-1/2" (38mm) above the bubbler guard (See Figure 5, Page 5).

10.Mount lower panel. Loosen the (2) #10-24 x 5/8" (16mm) screws at frame bottom lip. Slide upper tongue of lower panel under lower edge of already installed upper panel. Tighten previously loosened screws securely.

11.Replace bottom access panel to fountain basin using screws provided. Tighten securely.

Care and Maintenance of Halsey Taylor Marblyte Fountains

Marblyte provides an exremely durable, nonporous surface which resists staining. Care is very simple. Routine cleaning with a soft sponge or cloth, or with water or non-abrasive aerosol foam cleaner, is all that is normally needed to give many years of trouble free service. Cleaners left standing on the fountain surface can dull the surface finish. Be certain to rinse all cleaning agents completely and polish with a soft cloth.

Harsh abrasive cleaners are not required and should not be used.

Mild abrasives such as liquid automotive cleaning compound or baking soda paste will remove simple scratches and stains. Cigarette burns can normally be removed without noticeable effect. Deeper scratches or gouges can be corrected with fine grit sandpaper (240 grit then 400 grit) or a green Scotchbrite pad.

To maintain or regain luster and make cleaning easier, periodic applications of automobile wax or like products will keep the finish looking like new.

97716C (Rev. A - 5/02)

PAGE 4

HRFG - ERA, HRFG - SRA, HRFG - SER*A specifications

Halsey Taylor, a renowned brand in the water cooler and drinking fountain industry, has made a mark with its innovative HRFG line, specifically the HRFG - SER*A, HRFG - ER*A, and HRFG - SR*A models. These products combine functionality, sustainability, and advanced technology, catering to the needs of modern public spaces, schools, and workplaces.

One of the standout features of the Halsey Taylor HRFG series is its commitment to providing safe and clean drinking water. Each model is equipped with a patented filtration system that ensures optimal water quality, removing contaminants and offering enhanced taste. This is crucial, especially in environments where access to clean drinking water is essential.

The HRFG - SER*A model focuses on sustainability and energy efficiency. It is designed with a built-in WaterSense-compliant feature, which helps minimize water usage without compromising performance. With an elegant design, it can seamlessly integrate into any setting while encouraging users to stay hydrated.

In contrast, the HRFG - ER*A is tailored for high-traffic areas, such as schools and public parks. This unit boasts a robust construction meant to withstand heavy use and features vandal-resistant components, ensuring durability over time. Moreover, it provides the convenience of dual hydration options, allowing users to fill up both reusable bottles and drink directly from the fountain.

Meanwhile, the HRFG - SR*A model offers a streamlined aesthetic and is designed to be space-efficient. It features a compact design that makes it ideal for areas that require a drinking solution with minimal footprint. The model also includes user-friendly technology, such as an ergonomic design and easy-to-use controls, enhancing the overall user experience.

All models in the Halsey Taylor HRFG series incorporate advanced cooling technology, enabling them to deliver refreshing chilled water even during peak usage times. This feature is particularly appreciated in outdoor venues or in warmer climates where user demand for chilled water is high.

In summary, the Halsey Taylor HRFG - SER*A, HRFG - ER*A, and HRFG - SR*A models exemplify innovation in drinking infrastructure. With their focus on safety, sustainability, and user experience, these units set a new standard for drinking fountains and water coolers, making them ideal choices for enhancing hydration in various public and private settings. Each model's distinct features ensures that there is a perfect fit for every need, appealing to environmentally conscious consumers and institutions alike.

HRFG - ER*A HRFG - SR*A HRFG - SER*A