When Antenna Source is set to Satellite:
■■ Channel Type (All / TV / Radio): Select the Channel type to memorise.
■■ Satellite: Selects the satellite to scan.
■■ Scan Mode (All Channels / Free Channels Only): Selects the scanning mode of the selected satellite.
Manual Store
Scans for a channel manually and stores in the TV.
✎✎If a channel is locked using the Child Lock function, the PIN input window appears.
When Antenna Source is set to Air or Cable:
■■ Digital Channel: When scanning has finished, channels are updated in the channel list.
✎✎ When selecting Antenna → Air: Channel, Frequency, Bandwidth
✎✎ When selecting Antenna → Cable: Frequency, Modulation, Symbol Rate
■■ Analogue Channel (Programme, Colour System, Sound System, Channel, Search): If there is abnormal sound or no sound, reselect the sound standard required.
✎✎Channel mode
xx P (programme mode): When tuning is complete, the broadcasting stations in your area have been assigned to position numbers from P0 to P99. You can select a channel by entering the position number in this mode.
xx C (aerial channel mode) / S (cable channel mode): These two modes allow you to select a channel by entering the assigned number for each aerial broadcasting station or cable channel.
When Antenna Source is set to Satellite:
■■ Satellite: Selects the satellite using the up/down buttons.
■■ Transponder: Selects the transponder using the up/ down buttons.
■■ Scan Mode (All Channels / Free Channels Only): Selects either free or all channels to store.
■■ Network Search (Disable / Enable): Enable / Disable network search using the up/down buttons.
■■ Signal Quality: Display the current status of broadcasting signal.
✎✎Information on a satellite and its transponder is subject to change depending on the broadcasting conditions.
✎✎When setting is completed, move to Search and press the ENTEREbutton. Channel scan is started.
Satellite System Setup
The PIN input screen appears. Enter your 4 digit PIN number. Satellite System Setup is available when Antenna is set to Satellite. Before running Auto Store, set
Satellite System Setup. Then channel scan is run normally.
■■ Satellite Selection: You can choose the satellites for this TV.
■■ LNB Power (Off / On): Enables or disables the power supply for the LNB.
■■ LNB Settings: Configures the outdoor equipment.
■■ Satellite: Selects the satellite for receiving digital broadcasts.
Transponder: Selects a transponder from the list or adds a new transponder.
DiSEqC Mode: Selects DiSEqC mode for the selected LNB.
Lower LNB Oscillators: Sets the LNB oscillators to a lower frequency.
Upper LNB Oscillators: Sets the LNB oscillators to a higher frequency.
Tone 22 kHz (Off / On / Auto): Selects the Tone 22 kHz depending on the LNB type. For a universal LNB it should be Auto.
Signal Quality: Display the current status of broadcasting signal.
■■ Positioner Settings: Configures the antenna positioner.
Positioner (On / Off): Enables or disables the positioned control.
Positioner Type (USALS / DiSEqC 1.2): Sets the positioned type between DiSEqC 1.2 and USALS(Universal Satellite Automatic Location System).
––My Longitude: Sets the longitude for my location.
––My Latitude: Sets the latitude for my location.
––Satellite Longitude Settings: Sets the longitude of user defined satellites.
User Mode: Sets the position of satellite antenna according to each satellite. If you store the current position of satellite antenna according to a certain satellite, when the signal of that satellite is needed, the satellite antenna can be moved to
––Satellite: Selects the satellite to set the position for.
––Transponder: Selects a transponder from the list for signal reception.
––Moving Mode: Selects the movement mode between discrete and continuous movement.
––Step Size: Adjusts the step size degrees for the antenna rotation. Step Size is available when Moving Mode is set to Step.
03 Basic Features