Finishing instructions | Therma-Tru Pre-hung Door Systems manual

Finishing instructions.

Work only when temperatures are btween 50º and 90ºF and with humidity less than 85%. Do not finish in direct sunlight.

STEEL and SMOOTH-STAR® Doors:

To Paint Doors: Clean first with mild detergent and water or use a TSP (tri-sodium phosphate) solution. Rinse well and allow to dry completely. Use high-quality acrylic latex house paint, following manufacturer’s directions for appllication. Use exterior grade finishes for outside surfaces. Paint edges and exposed ends of door.

To paint Doorlite Frames: Remove any excess glazing sealant by first spraying with a window cleaner or water. Use a single edge razor blade to score the glazing along the edge of the frame. Holding the razor blade at a 45º angle, scrape glazing from glass. Wipe remaining residue off with window cleaner or mineral spirits. Clean frame with a mild detergent and water, or use a TSP solution. Rinse well and allow to dry completely. Mask off glass. Prime doorlite frames with

an alkyd- or acrylic-based primer. Allow primer to dry before applying finish paint coats. Use high-quality acrylic latex house paint, following paint manufacturer’s application insrtuctions. Use exterior grade finishes for outside surfaces.

CLASSIC-CRAFT® and FIBER-CLASSIC® Doors:

To Finish Doorlite Frames and Panel Inserts: Remove any excess glazing sealant by first spraying with a window cleaner or water. Use a single edge razor blade to score the glazing along the edge of the frame. Holding the razor blade at a 45º angle, scrape glazing from glass. Wipe remaining residue off with window cleaner or mineral spirits. Mask off glass. Paint or stain using same materials as for the door. (See below.)

To Paint Doors: Clean first with mild detergent and water or use a TSP (tri-sodium phosphate) solution. Rinse well and allow to dry completely. Prime with an alkyd- or acrylic-based primer. Allow primer to dry completely, then paint with oil- based or acrylic latex house paint, following paint manufactur- er’s application instructions. Use a primer and paint that are compatible. Use exterior grade finishes for outside surfaces. Paint edges and exposed ends of door.

To Stain Doors: Clean first with a clean cloth and mineral spirits and allow to air dry OR wash door with a mild detergent and water, or a TSP (tri-sodium phosphate) solution. Rinse well and allow to dry completely. For stained surfaces, we only recommend the use of the stain and clear coat products found in the Therma-Tru Same-Day Stain Finishing kit. Apply stain with a rag. The longer the stain is left to “setup” before wiping off, the darker the color will be. Using a clean rag, wipe off the stain to the color shade you desire. Remove any excess stain from the panel grooves with the foam brush provided. Allow the stain to dry for at least 6 hours before applying topcoat. See Therma-Tru Same-Dat Stain Finishing Kit Instructions for complete details.

Therma-Tru Doors is an operating company of Fortune Brands, Inc.

Issued 7/08 Rev.E MSDRIST

Instrucciones para el termindo.

Trabaje solamente a temperaturas entre 50º y 90ºF y a un nivel de humedad inferior a 85%. No aplique el terminado bajo la liz directa del sol.

PUERTAS STEEL y SMOOTH-STAR:

Para pintar las puertas: Limpie primero con detergente suave y

`	`
agua o con una solucion de fosfato trisodico. Enjuague bien y deje
	`	`
secar por completo. Utilice pintura residencial acriclica de latex de
`

alta calidad y apliquela siguiendo las instrucciones del fabricante. Use terminados para intemperie para las superficies exteriores. Pinte los bordes y los extremos expuestos de la puerta.

Para pintar los marcos de los ventanales: Retire cualquier remanente de sellador para cristales rociando con un limpiador para vidrios o agua. Util una navaja para rasurar de un solo filo para retirar el sellador a lo largo del borde del marco. Sostenga la

	`
navaja en un angulo de 45º y raspe el sellador del vidrio. Limpie
los residuos con limpiador para vidrios o alcohol mineral. Limpie
	`
el marco con un detergente suave y agua o una solucion de fosfato
`
trisodico. Enjuague bien y deje secar por completo. Proteja el		`
vidrio con cinta de enmascarar. Aplique un imprimador alquidico o
`
acrilico en los marcos de los ventanales. Permita que se seque el
imprimador antes de aplicar las capas de pintura de acabado.
	`
Utilice pintura residencial acriclica de latex de alta calidad y
`

apliquela siguiendo las instrucciones del fabricante. Use termina- dos para intemperie para las superficies exteriores.

PUERTA CLASSIC-CRAFT y FIBER-CLASSIC:

Terminado de los marcos de ventanales e insertos en los paneles:

Retire cualquier remanente de sellador para cristales rociando con un limpiador para vidrios o agua. Utilice una navaja para rasurar de un solo filo para retirar el sellador a lo largo del borde del marco.

Sostenga la najava en un angulo` de 45º y raspe el sellador del vidro. Limpie los residuos con limpiador para vidros o alcohol mineral. Proteja el vidrio con cinta de enmascarar. Pinte o entinte con los mismos materiales de la puerta (ver en seguida).

Para pintar las puertas: Limpie primero con detergente suave y
agua o con una solucion de fosfato trisodico. Enjuaggue bien y deje
`	`
secar por completo. Aplique imprimador alquidico o acrilico.
		`	`
Permita que se seque el imprimador por completo y pinte
con pintura residencial de aceite o acriclica de latex de alta calidad
	`		`
aplicandola segun las instrucciones del fabricante. Use un impri-
`
mador y una pintura compatibles. Use terminados para intemperie
para las superficies exteriores. Pinte los bordes y los extremos
expuestos de la puerta.
		~
Para entintar las puertas: Pase primero con un pano limpio y alcoholes

minerales y deje secar O lava la puerta con un detergente suave y aqua
o una solucion TSP (fosfato trisodico). Enjuague bien y deje secar com-
`
pletamente. Para superficies tintadas, recomendamos unicamente el
	`
uso del tinte y los productos que brinden una capa transparente en el
	~
juego de acabado Therma-Tru. Aplique el tinte con un pano. Mientras

mas tiempo el tinte se deje permanecer. Antes de pasar la brocha, mas
`	`
oscuro quedara el color. Pase una brocha de cerdas naturales en la

misma direccion`

de la veta para integrar o fusionar el tinte de forma que

aporte una elegante apariencia de madera. Limpie frecuentemente la
~
punta de la brocha con un pano seco para retirar el exceso de tinte.
Tinte y pase la brocha en cada seccion,`	una de cada vez, hasta terminar.
Deje transcurrir un minimo de 48 horas de tiempo de secado antes de

que cure el tinte antes de aplicar la capa transparente. Para mas`		infor-
`	`

macion, refierase a las instrucciones en el Juego de acabado Therma-Tru.

Pre-hung Door Systems specifications

Therma-Tru Pre-hung Door Systems have established themselves as a popular choice among homeowners and builders alike, known for their quality, durability, and aesthetic appeal. These door systems are factory-prepped for easy installation, ensuring that both first-time homeowners and seasoned builders can achieve professional results with minimal effort.

One of the main features of Therma-Tru Pre-hung Door Systems is their energy efficiency. These doors are designed to minimize heat transfer, which leads to energy savings and improved interior comfort. The use of advanced insulation materials and the option for double or triple glazing in glass door models further enhance their energy performance, contributing to lower heating and cooling costs.

In terms of design flexibility, Therma-Tru offers a wide range of styles, colors, and finishes, catering to diverse architectural tastes. Whether you prefer the classic look of a traditional wooden door or the sleek appearance of fiberglass, there are options available. Additionally, customization possibilities include decorative glass inserts, sidelites, and transoms, allowing homeowners to create a unique entryway that complements their home’s exterior.

Durability is another hallmark of Therma-Tru Pre-hung Door Systems. Built with high-quality materials, these doors resist warping, rusting, and other forms of wear. The fiberglass models, in particular, are engineered to withstand harsh weather conditions while maintaining their appearance and functionality over time. This resilience makes them an ideal choice for those living in diverse climates.

A notable technology employed by Therma-Tru is the use of advanced sealing systems. These systems include weather stripping and door sweeps that provide optimal sealing against air and water infiltration. This not only enhances energy efficiency but also ensures that the doors perform reliably in inclement weather, resisting moisture and drafts.

Therma-Tru also places a strong emphasis on security. Many of their pre-hung door systems feature multi-point locking mechanisms, which enhance the security of your home. This added feature is crucial for safeguarding against unauthorized entry, providing peace of mind for homeowners.

In summary, Therma-Tru Pre-hung Door Systems stand out for their energy efficiency, design versatility, durability, advanced sealing technologies, and enhanced security features. With a commitment to quality and innovation, Therma-Tru continues to be a leader in the door industry, making their pre-hung door systems a smart choice for any home renovation or construction project.