Samsung HTDB390RH/ELS manual Before Calling for Service, Sound can be heard only

Page 66

Before Calling for Service

Refer to the chart below when this unit does not function properly. If the problem you are experiencing is not listed below or if the instruction below does not help, turn off the unit, disconnect the power cord, and contact the nearest authorized dealer or Samsung Electronics Service Center.

Symptom

Check/Remedy

	Disc tray does not open.	• Is the power cord plugged securely into the outlet?
		• Turn off the power and then turn it back on.

	Playback does not start.	• Check the region number of the DVD.
	Playback does not start.	DVD discs purchased from abroad may not be playable.
		• CD-ROMs and DVD-ROMs cannot be played on this DVD
		player.
		• Make sure that the rating level is correct.

	Playback does not start	• Are you using a deformed disc or a disc with scratches on
	immediately when the	• Are you using a deformed disc or a disc with scratches on
	immediately when the	the surface?
	Play/Pause button is pressed.	• Wipe the disc clean.

	Sound is not produced.	• No sound is heard during fast playback, slow playback, and step
	Sound is not produced.	motion playback.
		• Are the speakers connected properly? Is the speaker setup
		correctly customized?
		• Is the disc severely damaged?

	Sound can be heard only	• When listening to a CD or radio, sound is output to the front
		speakers (L/R) only. Select "PRO LOGIC II" by pressing
		speakers (L/R) only. Select "PRO LOGIC II" by pressing
	from a few speakers and	(Dolby Pro Logic II) on the remote control to use all six speakers.
	not all six.	• Make sure that the DVD disc is 5.1-CH compatible.
	not all six.	• If you set C, SL, and SR to NONE in the speaker mode in the
		audio setup of the setup screen, no sound is heard from the
		center speaker and the front left and right speakers. Set C, SL,
		and SR to SMALL.

	Picture does not appear, sound	• Was the DVD player suddenly moved from a cold place to a warm
	is not produced, or the disc	one? When condensation forms inside the player, remove the disc
	is not produced, or the disc	and let the player stand for 1 or 2 hours with the power on. (You
	tray opens 2 to 5 seconds later.
	tray opens 2 to 5 seconds later.	can use the player again after condensation disappears.)

	Dolby Digital 5.1 CH	• Is there "Dolby Digital 5.1 CH" mark on the disc? Dolby Digital 5.1
	Surround Sound is not	CH Surround Sound is produced only if the disc is recorded with
	Surround Sound is not	5.1 channel sound.
	produced.	• Is the audio language correctly set to DOLBY DIGITAL 5.1-CH in
		the information display?

65

Image 66

Contents Digital Home Cinema System Safety Warnings Class 1 Laser ProductPrecautions PreparationFeatures Multi-Disc Playback & AM/FM TunerContents Mark Logo Copy ProtectionDisc Size Max. Playing TimeCD-R Discs CD-R MP3 DiscsCD-R Jpeg Discs Description Connector Video Output ConnectorInput Connector External Audio ComponentTV indicator Auto Sound Calibration buttonReplace the battery cover Range of Operation of the Remote ControlConnecting the Speakers Selecting the Listening PositionInstalling the Center Speaker to the Stand Connect the connecting jacks to the back of the DVD playerPlace the center speaker on the stand R, to On the front panel Wireless rear amplifier Connecting Wireless Rear SpeakersWireless rear speakers Connect your pairPower Standby mode, press the ON/OFF button Press the Power buttonPlease observe the following cautions for your safety Coaxial terminal as a temporary measureConnect the FM antenna supplied to the FM 75Ω Connecting the Video to TV Connecting External Components Connecting an External Digital ComponentConnecting an External Analog Component Press AUX on the remote control to select AUX 1 or AUXAC power supply Selecting the Video FormatTurn off the main unit and then press NTSC/PAL Press DVD button to select DVD/CD mode Press the Power button to turn on the TVPress the Mode button so Press Mode buttonTo stop playback Press Stop during playback Disc PlaybackPress OPEN/CLOSE button to open the disc tray Load a disc Playback starts automaticallyDisplaying Disc Information Press Info buttonFast/Slow Playback Press and holdPress Slow button Skipping Scenes/Songs Briefly pressRepeat Playback Options Repeat PlaybackPress Repeat button Press Info button twicePress Enter Press Info button twicePress Cursor A-B Repeat function will not work on an MP3 or Jpeg discAngle Function Button Zoom FunctionPress Zoom Press EZ View buttonTwice 1Press Info button twicePress Info button Press Cursor Subtitle displayTime display 1Press Info buttonPress Cursor , buttons Chapter displaySelect the desired Using Disc MenuPress Cursor Buttons to Press Enter PBC Playback Control FunctionPress Menu Using the Title MenuPress Menu button to exit the setup screen Button to move toPress Enter button Setting the Language‘Setup’ and then Button to move toPress Enter Press Cursor Press Enter buttonDISPLAY’ and then Setting TV Screen typePress Cursor 2 button to move to ‘Setup’ and then Press Cursor 3 button to move to ‘TVLetterbox 43 Pan&ScanSetting Parental Controls Rating Level Enter the password Press Cursor , buttonPress Cursor 3 button to move to Setting the Password Press Cursor Button to move to Press Menu buttonButton Enter button During playback, press Setting the Wallpaper Jpeg DVD VCD1PLAY/PAUSE button when the image you like comes up Press Cursor 6 button to move to ‘USER’ and then‘Setup’ and then Button to open and thenPress Enter button Press Cursor Setting the Speaker ModeSpeaker Speaker and then press Enter buttonPress Test Tone button Setting the Test Tone‘Audio’ and then Press Cursor buttonSetting the Delay Time Press Cursor buttonPress Menu button to move to ‘Audio’ and then press Enter Setting Center Speaker 3to move to ‘DELAY TIME’ and then press Enter buttonPress Cursor , 5 totime.set the Delay Setting Rear Surround SpeakersSetting the Audio Quality You can adjust the balance and level for each speakerEnter button Press Cursor button Method 2 When manually adjusting with the Sound Edit button Press SoundSetting the DRC Dynamic Range Compression To adjust the ‘DRC’.Press Cursor ‘DRC’ and then press Enter buttonTo Verify the Auto Sound Calibration To Turn On or Off Sound LogoPress and hold ASC button Briefly press ASC button Press and hold ASC button twice Briefly press ASC buttonAdjust the volume control on the main Unit as follows When the message Remove MICPress ASC button Magic Sound Field Mode Press SUPER5.1Music Sound Field Function Magic Headphone Function PlugDolby Pro Logic II Mode Press PL II Mode buttonYou can select the desired Dolby Pro Logic II audio mode Dolby Pro Logic II Effect Press PL II ModeButton to select ‘MUSIC’ mode Press PL II Effect buttonBand button Remote Control Unit Press TunerListening to Radio Main UnitPress Presetting StationsTo preset another Press 1button and selectUsing the RDS Radio Data System to receive FM stations What information can RDS signals provide?About RDS broadcasting PTY Search is only applicable to preset stations PTY Program Type indication and PTY-SEARCH functionBefore you start, remember Press Sleep button To confirm the sleep timer setting, press Sleep buttonConvenient Functions OFF appears on the displayPress Dimmer button Press Mute buttonOperating the TV with the Remote Control While holding down POWER, enter the codeTV Brand Code List Brand CodeBefore Calling for Service Sound can be heard onlyIs not produced, or the disc Remote control does not Aspect ratio cannot beMain unit is not working Handling discs Disc StorageHandling and Storing Discs Specifications 1ch speaker systemSubwoofer speaker Subtitle languages Be chosen from the menu displayed on the TV monitorDVD player, the player cannot play the disc Movies, these movies are numbered as Title 1, Title 2, etcMemo AH68-01445K