Enviro C-10078, C-11278, 50-645 owner manual Must be not visible, Removing valve Screw

Page 13
Figure 13: O-ring on valve screw.

Maintenance And Service

7.Convert the SIT gas valve:

a)Remove the black protection cap from the HI/LO knob by hand shown in Figure 10.

Figure 11: Removing valve

screw.

b)Insert a 5/32” or 4 mm Allen wrench into the hexagonal key-way of the screw (see Figure 11), rotate it counter-clockwise until it is free and extract it.

c)Check that the screw is clean and if necessary remove dirt.

d)Flip the screw (refer to Figure 12).

e)Using the Allen wrench as shown in Figure 11, rotate the screw clockwise until a torque of 9 inch lbs. WARNING! Do not over tighten the screw. It is recommended that you grip the wrench by the short side.

f)Verify that if the conversion is from NG to LPG, the screw must be re-assembled with the red o- ring visible (refer to Figure 13). If the conversion is from LPG to NG, the red o-ring of the screw

must be not visible.

Figure 12: Flip valve

 

screw.

g)Re-attach the black protection cap that was removed in step a (Figure 10).

8.Reinstall the burner, brick panels, log set, embers, and glass door.

Also refer to Secondary Installation - Log Set and Embers Installation.

When re-installing the burner, ensure that the burner to pilot hood

relationship is similar to what is shown in Figure 14. On some units you will need to pay special attention when installing the burner that the venturi adjustment rod is properly installed into the venturi adjustment piece welded to the burner venturi tube

9.Reconnect the main gas line if it was disconnected and open the shut-off valve at the gas line to the unit.

10.Use a small brush to apply a warm soapy water solution to all gas connections (use a half dish soap and half warm water). If a gas leak is present, bubbling will occur. Gas leaks can be repaired by using an approved pipe thread sealant or approved Teflon tape. NEVER USE AN OPEN FLAME WHEN TESTING FOR LEAKS.

11.Reconnect the electrical power to the unit.

Figure 14. Ignitor

assembly beside the

burner.

12.Relight the main burner in both the “HI” and “LO” positions to verify proper burner ignition and operation and proper flame appearance. Also refer to Secondary Installation - Log Set and Embers Installation for a flame appearance picture.

13.MAKE SURE that the conversion label is installed on or close to the rating label to signify that the unit has been converted to a different fuel type.

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Consumer InstallerS H E R W O O D I N D U S T R I E S L T D General Safety PrecautionsTable of Contents Vented GAS Fireplace Heater DV42DX NG/LPG Codes And ApprovalsThis Enviro DV42DX Fireplace Installation Options SpecificationsDimensions Rating Label LocationPilot Lighting Instructions Operating InstructionsPilot Light Venturi AdjustmentAir Diverter Control To Turn GAS Fireplace OFF No substitute materials are allowed Maintenance And ServiceGlass Door Removal Cleaning Decorative SurfacesRemoval of DV42DX Burner and Fan Burner and Fan RemovalConversion Kit Installation Kit Parts ListWay, and snap into place Fuel ConversionRemoving valve Screw Must be not visibleIntroduction Placement Initial InstallationRaised Fireplaces and Hearths Corner InstallationFireplace Surround Rock or Brick Finish If the faceVent Termination Restrictions Mantel ClearancesFireplace Horizontal Vent Kit KIT ComponentsQnty Description Wire Spacer in Place Installation InstructionsOther Approved Vent Parts Manufacturer Trade Name Nominal SizesSV4L6 Direct Vent Secure Vent Ameri Vent Description TempAppliances To a chimney flue serving a separate solid-burningVenting Possible Vent Configurations Vent Configurations and Restrictor SettingsHorizontal Vent Termination Horizontal TerminationVertical Termination AssembleRoof Pitch Minimum Height H Feet Meters Use of Wall Straps Heat Dumping Options DuctingElectrical Requirements Wiring Diagram For Gas ValveTo Test Valve Pressures GAS Line ConnectionImportant installation notes Secondary InstallationLog Set and Ember Installation Never operate the fireplace with the glass door removedFirst Stage Log Set Installation Fourth Stage Log Set Installation Problem Possible Cause Solution TroubleshootingReference Description Part Number Parts List ComponentsPartsomponentsC Diagram Reference Options Part Number Parts List OptionsParts Diagram Options To the Dealer WarrantyWarranty Warranty Installation Data Sheet

50-645, C-10078, C-11278 specifications

Enviro C-11278, 50-645, and C-10078 are innovative solutions designed to address the growing environmental challenges faced by industries today. These products are crafted with a forward-thinking approach, centered on sustainability, efficiency, and effectiveness in various applications.

One of the main features of Enviro C-11278 is its advanced formulation that combines bio-based components with traditional materials, resulting in a product that minimizes environmental impact while maintaining high performance. This formulation is designed to reduce emissions, lower toxicity, and enhance biodegradability, making it an eco-conscious choice for industries ranging from manufacturing to construction.

The Enviro 50-645 stands out for its versatility and adaptability in various operational settings. Engineered to function effectively under diverse conditions, it integrates seamlessly into different processes, requiring minimal adjustments. Its robust composition ensures durability and longevity, reducing the need for frequent replacements, and ultimately contributing to waste reduction.

C-10078 is particularly noted for its cutting-edge technology that incorporates smart monitoring capabilities. This feature allows for real-time data collection and analysis, enabling users to optimize processes and reduce resource consumption. The intelligent design not only enhances efficiency but also supports compliance with environmental regulations, making it a valuable asset for companies striving for sustainability.

In terms of characteristics, all three products exhibit high resistance to chemical degradation, ensuring consistent performance over extended periods. They are also formulated to be water-resistant, providing reliability in varied environmental conditions. The eco-friendly nature of these products does not compromise their performance; conversely, they are designed to outperform many traditional solutions in both effectiveness and safety.

Furthermore, the manufacturing processes for Enviro C-11278, 50-645, and C-10078 focus on minimizing energy consumption and reducing waste. By prioritizing renewable resources and sustainable practices, these products not only serve their intended purpose but also align with global efforts to combat climate change.

In summary, Enviro C-11278, 50-645, and C-10078 represent a significant advancement in environmentally responsible product offerings. Their unique features, innovative technologies, and commitment to sustainability position them as optimal choices for industries looking to reduce their ecological footprint while ensuring operational efficiency and safety. By integrating such products, businesses can take meaningful steps towards a greener future.
Top Page Image Contents