Enviro C-10078, C-11278, 50-645 owner manual Assemble, Vertical Termination

Page 25

Initial Installation

QUALIFIED INSTALLERS ONLY

NOTE: For Simpson Duravent only, place a bead of Mil-Pac or Rutland No 78 Stove and Gasket Cement on the outer edge of the inner exhaust pipe (non-flared end). Push the pipe sections together, then twist about ¼ turn, making sure the two sections are fully locked. Wrap all seams with foil ducting tape.

Step 4. With the hole now framed, the wall thimble installed, and the pipe extending into the wall, proceed to the outside. Attach the termination to the pipe using RTV and Mil-Pac or Rutland No 78 Stove and Gasket Cement to seal joints. The vent pipe must extend into the vent cap at least 1¼ inches (3.2 cm). Secure the connection between the vent cap and the pipe by attaching the two (2) sheet metal straps, which extend from the vent cap assembly to the outer wall of the vent pipe. Bend any remaining portion of the strap back towards the vent cap. Security Secure Vent uses a twist lock cap.

Step 5. Position the horizontal vent termination in the center of the 10 inches (25.4 cm) square hole and attach to the exterior wall with the four screws provided. The arrow on the vent termination should be pointing up. Run a bead of non-hardening mastic around the edges of the vent cap, to make a seal with the wall. Ensure the proper clearances to combustibles have been maintained.

Vertical Termination:

Step 1. Check the instructions for required clearances (air spaces) to combustibles when passing through ceilings, walls, roofs, enclosures, attic rafters, or other nearby combustible surfaces. Do not pack air spaces with insulation.

Step 2. Set the gas appliance in the desired location. Drop a plumb bob down from the ceiling to the position of the appliance flue exit, and mark the location where the vent will penetrate the ceiling. Drill a small hole at this point. Next, drop a plumb bob from the roof to the hole previously drilled in the ceiling, mark the spot where the vent will penetrate the roof. Determine if ceiling joists, roof rafters, or other framing will obstruct the venting system. You may wish to relocate the appliance, or to offset, to avoid cutting load bearing members.

Step 3. To install the Round Support Box/Wall Thimble in a flat ceiling, cut a 10 inch (25.4 cm) square hole in the ceiling, centered in the hole drilled in Step 2. Frame the hole as shown in Figure 29.

Step 4. Assemble

the desired

lengths

of

black

pipe

and elbows

necessary to

reach from the appliance

adapter

up

through

the

Round

Support

Box.

Insure that all pipe and

elbow

connections

are

in their fully twist-locked position.

 

Vertical

 

Termination

Elbow Strap

Storm Collar

 

Flashing

 

Roofing nails

Figure 33. Vertical Vent Termination

25

Page 24 Page 26
Image 25
Page 24 Page 26
Contents Consumer InstallerS H E R W O O D I N D U S T R I E S L T D General Safety PrecautionsTable of Contents Vented GAS Fireplace Heater DV42DX NG/LPG Codes And ApprovalsThis Enviro DV42DX Fireplace Installation Options SpecificationsDimensions Rating Label LocationPilot Lighting Instructions Operating InstructionsPilot Light Venturi AdjustmentAir Diverter Control To Turn GAS Fireplace OFF No substitute materials are allowed Maintenance And ServiceGlass Door Removal Cleaning Decorative SurfacesRemoval of DV42DX Burner and Fan Burner and Fan RemovalConversion Kit Installation Kit Parts ListWay, and snap into place Fuel ConversionRemoving valve Screw Must be not visibleIntroduction Placement Initial InstallationRaised Fireplaces and Hearths Corner InstallationFireplace Surround Rock or Brick Finish If the faceVent Termination Restrictions Mantel ClearancesFireplace Horizontal Vent Kit KIT ComponentsQnty Description Wire Spacer in Place Installation InstructionsOther Approved Vent Parts Manufacturer Trade Name Nominal SizesSV4L6 Direct Vent Secure Vent Ameri Vent Description TempAppliances To a chimney flue serving a separate solid-burningVenting Possible Vent Configurations Vent Configurations and Restrictor SettingsHorizontal Vent Termination Horizontal TerminationVertical Termination AssembleRoof Pitch Minimum Height H Feet Meters Use of Wall Straps Heat Dumping Options DuctingElectrical Requirements Wiring Diagram For Gas ValveTo Test Valve Pressures GAS Line ConnectionImportant installation notes Secondary InstallationLog Set and Ember Installation Never operate the fireplace with the glass door removedFirst Stage Log Set Installation Fourth Stage Log Set Installation Problem Possible Cause Solution TroubleshootingReference Description Part Number Parts List ComponentsPartsomponentsC Diagram Reference Options Part Number Parts List OptionsParts Diagram Options To the Dealer WarrantyWarranty Warranty Installation Data Sheet

50-645, C-10078, C-11278 specifications

Enviro C-11278, 50-645, and C-10078 are innovative solutions designed to address the growing environmental challenges faced by industries today. These products are crafted with a forward-thinking approach, centered on sustainability, efficiency, and effectiveness in various applications.

One of the main features of Enviro C-11278 is its advanced formulation that combines bio-based components with traditional materials, resulting in a product that minimizes environmental impact while maintaining high performance. This formulation is designed to reduce emissions, lower toxicity, and enhance biodegradability, making it an eco-conscious choice for industries ranging from manufacturing to construction.

The Enviro 50-645 stands out for its versatility and adaptability in various operational settings. Engineered to function effectively under diverse conditions, it integrates seamlessly into different processes, requiring minimal adjustments. Its robust composition ensures durability and longevity, reducing the need for frequent replacements, and ultimately contributing to waste reduction.

C-10078 is particularly noted for its cutting-edge technology that incorporates smart monitoring capabilities. This feature allows for real-time data collection and analysis, enabling users to optimize processes and reduce resource consumption. The intelligent design not only enhances efficiency but also supports compliance with environmental regulations, making it a valuable asset for companies striving for sustainability.

In terms of characteristics, all three products exhibit high resistance to chemical degradation, ensuring consistent performance over extended periods. They are also formulated to be water-resistant, providing reliability in varied environmental conditions. The eco-friendly nature of these products does not compromise their performance; conversely, they are designed to outperform many traditional solutions in both effectiveness and safety.

Furthermore, the manufacturing processes for Enviro C-11278, 50-645, and C-10078 focus on minimizing energy consumption and reducing waste. By prioritizing renewable resources and sustainable practices, these products not only serve their intended purpose but also align with global efforts to combat climate change.

In summary, Enviro C-11278, 50-645, and C-10078 represent a significant advancement in environmentally responsible product offerings. Their unique features, innovative technologies, and commitment to sustainability position them as optimal choices for industries looking to reduce their ecological footprint while ensuring operational efficiency and safety. By integrating such products, businesses can take meaningful steps towards a greener future.
Top Page Image Contents