Enviro C-10078, C-11278, 50-645 owner manual Rock or Brick Finish If the face, Fireplace Surround

Page 16

Initial Installation

QUALIFIED INSTALLERS ONLY

 

 

 

If the unit is raised less than

 

 

 

 

 

 

3” (76mm) it is mandatory to

 

 

 

have a hearth installed with

 

 

 

a protector pad (sheet metal)

 

 

 

placed directly on the floor or

 

 

 

hearth framing, with the cement

 

 

 

board (see specs below) on

 

 

 

top of it. Tile, or another non-

 

 

 

combustible material

forms

 

 

 

the top layer of the hearth. A

Figure 19. Raised Fireplace with

 

Figure 20. Floor Level Hearth

decorative trim may be

added

Raised Hearth

 

Requirements

to the edge of the hearth. The

 

 

 

trim can be combustible as long as the hearth extends at least 12” (305 mm) in front of the fireplace and 1” (25 mm) on either side of the fireplace opening. To install the face, it is necessary for the bottom flange of the fireplace opening to overlap or be flush with the tile. If the total thickness of the protector pad, cement board, and finished tile is more than 1” (25 mm) the fireplace must be raised to accommodate additional thickness. NOTE: The Manor (the cast iron) face does NOT require any floor protection even when installed at floor level.

Fireplace Surround:

NOTE: Any paint that is applied to the mantel or facing above the unit should be “heat resistance” or it may discolour.

CEMENT BOARD: The cement board can be fastened to the front of the unit with self-drilling metal screws. It is safe to screw to the outer border of the fireplace. Cement board for the hearth can be purchased at a local building material store. The board must have a k-value of 7.69 (metric version: 13 W/m × K) and a R-value of 0.13 (metric version: 0.023 m² × K/W) or better.

TILED FINISH: Because of the amount of heat exuded by the fireplace, drywall cannot come directly up to the fireplace. Figure 21 shows the minimum dimensions for the cement board. Tile or other non- combustible materials cover the cement board, but do not overlap into the fireplace opening. The total depth of the cement board and the finishing materials should be a minimum of 1” (25 mm) to maximum of 1⅜” (35 cm). The fireplace front will be installed over top of the finishing material.

 

SMOOTH FINISH: The fireplace will have to be

 

 

recessed by ½” (12 mm) and two (2) layers of

 

cement board must be used if the area around the

 

fireplace will be finished flush with the rest of the

 

wall.

 

ROCK OR BRICK FINISH: If the face of the

 

fireplace is to be recessed, the face option

 

chosen will determine the size and shape of the

 

surrounding material (i.e. brickwork). Since the

 

dimensions provided on the face option instruction

 

sheet are only approximations it is recommended

 

that the steel template of the chosen face is used.

 

See Parts List - Options for the face template part

 

number.

Figure 21. Dimensions Facing Around Opening.

 

16

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Consumer InstallerS H E R W O O D I N D U S T R I E S L T D Safety Precautions GeneralTable of Contents Vented GAS Fireplace Heater DV42DX NG/LPG Codes And ApprovalsThis Enviro DV42DX Fireplace Specifications Installation OptionsDimensions Rating Label LocationOperating Instructions Pilot Lighting InstructionsPilot Light Venturi AdjustmentAir Diverter Control To Turn GAS Fireplace OFF Maintenance And Service No substitute materials are allowedCleaning Decorative Surfaces Glass Door RemovalBurner and Fan Removal Removal of DV42DX Burner and FanKit Parts List Conversion Kit InstallationWay, and snap into place Fuel ConversionMust be not visible Removing valve ScrewInitial Installation Introduction PlacementCorner Installation Raised Fireplaces and HearthsRock or Brick Finish If the face Fireplace SurroundMantel Clearances Vent Termination RestrictionsFireplace Horizontal Vent Kit KIT ComponentsQnty Description Installation Instructions Wire Spacer in PlaceManufacturer Trade Name Nominal Sizes Other Approved Vent PartsDirect Vent Secure Vent Ameri Vent Description Temp SV4L6Appliances To a chimney flue serving a separate solid-burningVenting Vent Configurations and Restrictor Settings Possible Vent ConfigurationsHorizontal Termination Horizontal Vent TerminationAssemble Vertical TerminationRoof Pitch Minimum Height H Feet Meters Use of Wall Straps Ducting Heat Dumping OptionsWiring Diagram For Gas Valve Electrical RequirementsGAS Line Connection To Test Valve PressuresSecondary Installation Important installation notesLog Set and Ember Installation Never operate the fireplace with the glass door removedFirst Stage Log Set Installation Fourth Stage Log Set Installation Troubleshooting Problem Possible Cause SolutionParts List Components Reference Description Part NumberPartsomponentsC Diagram Parts List Options Reference Options Part NumberParts Diagram Options Warranty To the DealerWarranty Warranty Installation Data Sheet

50-645, C-10078, C-11278 specifications

Enviro C-11278, 50-645, and C-10078 are innovative solutions designed to address the growing environmental challenges faced by industries today. These products are crafted with a forward-thinking approach, centered on sustainability, efficiency, and effectiveness in various applications.

One of the main features of Enviro C-11278 is its advanced formulation that combines bio-based components with traditional materials, resulting in a product that minimizes environmental impact while maintaining high performance. This formulation is designed to reduce emissions, lower toxicity, and enhance biodegradability, making it an eco-conscious choice for industries ranging from manufacturing to construction.

The Enviro 50-645 stands out for its versatility and adaptability in various operational settings. Engineered to function effectively under diverse conditions, it integrates seamlessly into different processes, requiring minimal adjustments. Its robust composition ensures durability and longevity, reducing the need for frequent replacements, and ultimately contributing to waste reduction.

C-10078 is particularly noted for its cutting-edge technology that incorporates smart monitoring capabilities. This feature allows for real-time data collection and analysis, enabling users to optimize processes and reduce resource consumption. The intelligent design not only enhances efficiency but also supports compliance with environmental regulations, making it a valuable asset for companies striving for sustainability.

In terms of characteristics, all three products exhibit high resistance to chemical degradation, ensuring consistent performance over extended periods. They are also formulated to be water-resistant, providing reliability in varied environmental conditions. The eco-friendly nature of these products does not compromise their performance; conversely, they are designed to outperform many traditional solutions in both effectiveness and safety.

Furthermore, the manufacturing processes for Enviro C-11278, 50-645, and C-10078 focus on minimizing energy consumption and reducing waste. By prioritizing renewable resources and sustainable practices, these products not only serve their intended purpose but also align with global efforts to combat climate change.

In summary, Enviro C-11278, 50-645, and C-10078 represent a significant advancement in environmentally responsible product offerings. Their unique features, innovative technologies, and commitment to sustainability position them as optimal choices for industries looking to reduce their ecological footprint while ensuring operational efficiency and safety. By integrating such products, businesses can take meaningful steps towards a greener future.
Top Page Image Contents