Installation

OWNER’S MANUAL

LOCATING HEATER

This heater is designed to be mounted on a wall.

CEILING

NOTICE: This heater is intended for use as supplemental heat. Use this heater along with your pri- mary heating system. Do not in- stall this heater as your primary

WARNING: Maintain the mini- mum clearances shown in Figure

4. If you can, provide greater clear-

ances from floor, ceiling, and

6" Minimum From Sides of Heater

36" Minimum

heat source. If you have a central heating system, you may run system’s circulating blower while using heater. This will help circu- late the heat throughout the house. In the event of a power outage, you can use this heater as your primary heating source.

WARNING: A qualified ser- vice person must install heater. Follow all local codes.

CHECK GAS TYPE

Use only propane/LP gas. If your gas supply is not propane/LP, do not install heater. Call dealer where you bought heater for proper type heater.

INSTALLATION ITEMS

Before installing heater, make sure you have the items listed below:

•external regulator (supplied by installer, see page 9)

•piping (check local codes)

•sealant (resistant to propane/LP gas)

•equipment shutoff valve *

•ground joint union

•test gauge connection *

•sediment trap

•tee joint

•pipe wrench

*An CSA/AGA design-certified equip- ment shutoff valve with 1/8" NPT tap is an acceptable alternative to test gauge connec- tion. The optional CSA/AGA design-certi- fied equipment shutoff valve can be pur- chased from your dealer. See Accessory, page 18.

joining wall.

WARNING: Never install the heater

•in a bathroom (Models CG10P and CGS10P only. CG6P is al- lowed in bathroom. Check lo- cal codes.)

•in a recreational vehicle

•where curtains, furniture, cloth- ing, or other flammable objects are less than 36 inches from the front, top, or sides of the heater

•as a fireplace insert

•in high traffic areas

•in windy or drafty areas

CAUTION: This heater creates warm air currents. These currents move heat to wall surfaces next to heater. Installing heater next to vinyl or cloth wall coverings or operating heater where impurities (such as tobacco smoke, aromatic candles, cleaning fluids, oil or kerosene lamps, etc.) in the air exist, may discolor walls.

IMPORTANT: Vent-free heaters add mois- ture to the air. Although this is beneficial, installing heater in rooms without enough ventilation air may cause mildew to form from too much moisture. See Air for Combustion and Ventilation, pages 4 through 6.

CAUTION: If you install the heater in a home garage

•heater pilot and burner must be at least 18 inches above floor

•locate heater where moving ve- hicle will not hit it

For convenience and efficiency, install heater

•where there is easy access for operation, inspection, and service

•in coldest part of room

Right

Side

Left

Side

2" Minimum to Top

FLOOR of Carpeting, Tile,

or Other Combustible Material

Figure 4 - Mounting Clearances As Viewed From Front of Heater

INSTALLING HEATER TO WALL

Mounting Bracket

The mounting bracket is located on back panel of heater. It has been taped there for shipping. Remove mounting bracket from back panel.

Mounting

Bracket

Figure 5 - Mounting Bracket

INSTALLING THERMOSTAT SENSING BULB -

For T-Stat Models Only

Remove clip and bulb from shipping loca- tion. Place clip and bulb into operation loca- tion (see Figure 6)

Figure 6 - Moving Thermostat Sensing Bulb

Continued

107295

CG10P, CG6P, CGS10P specifications

Desa CGS10P, CG10P, and CG6P represent a line of advanced generator sets designed to meet the demanding energy needs of various applications, including residential, commercial, and industrial use. Their reliability and performance make them a popular choice among consumers looking for stable power solutions.

One of the standout features of the Desa CGS series is their robust engine technology. Each model is equipped with high-quality engines designed for efficiency and durability. The CGS10P, for example, features a powerful engine that delivers a substantial output, making it suitable for larger power requirements. The CG10P and CG6P, while slightly lower in output, still provide dependable power for most everyday applications.

The generators are equipped with advanced inverter technology, which allows them to produce clean and stable electricity. This is essential for powering sensitive electronics and appliances without the risk of surges or fluctuations that could lead to damage. The inverter technology also contributes to improved fuel efficiency, allowing users to maximize their runtime while minimizing fuel costs.

Portability is another critical characteristic of the Desa CGS series. These generators are designed with compactness in mind, making them easy to transport and store. Many models come with built-in handles and lightweight designs, allowing users to move them effortlessly for outdoor activities, camping, or emergency power situations.

The noise level of the Desa CGS series has been optimized to ensure a quieter operation compared to traditional generators. This acoustic engineering means that users can rely on these generators for power without disturbing neighbors or creating an unbearable noise during operation.

Safety features are paramount in the design of these generators. Each model includes automatic shut-off mechanisms that activate in case of low oil pressure or overheating, ensuring the longevity of the unit and the safety of users. Additionally, the CGS series often incorporates multiple outlets, providing versatility for connecting various devices.

In summary, the Desa CGS10P, CG10P, and CG6P generators combine advanced engine technology, inverter capabilities, and user-friendly design, making them ideal for diverse power needs. Their reliability, fuel efficiency, and safety features position them as excellent choices for anyone in need of a dependable power supply. Whether for home use, outdoor events, or as a backup during outages, these generators are equipped to handle a variety of situations efficiently.