Desa CGN10RLA Installing Two Mounting Screws, Placing Heater on Mounting Screws

Page 8

CGN10RLA

NATURAL GAS HEATER

INSTALLATION

Continued

Installing Two Mounting Screws

Note: Wall anchors and mounting screws are in hardware package. The hardware pack- age is provided with heater.

Attaching to Wall Stud Method

For attaching mounting screw to wall stud

1.Drill hole at marked location using 9/64" drill bit.

2.Insert mounting screw into wall stud.

3.Tighten screw until 1/16" space (thick- ness of penny) is between screwhead and wall.

Attaching to Wall Anchor Method

Follow instructions below to attach mounting screws to hollow walls (wall areas between studs) or solid walls (concrete or masonry).

1.Drill holes at marked locations using 5/16" drill bit. For solid walls (concrete or masonry), drill at least 1 1/4" deep.

2.Fold wall anchor (see Figure 6).

3.Insert wall anchor (wings first) into hole. Tap anchor flush to wall.

4.For thin walls (1/2" or less), insert red key into wall anchor. Push red key to “pop” open anchor wings (see Figure 7). IMPORTANT: Do not hammer key! For thick walls (over 1/2" thick) or solid walls, do not pop open wings.

5.Tighten two screws until 1/16" space (thickness of penny) is between screwheads and wall (see Figure 8).

Thin or Thick Wall

(thick wall shown)

1/16" Space

Solid

Wall

Figure 8 - Tightening Anchors

Placing Heater on Mounting Screws

1.Locate two keyhole slots on back panel of heater (see Figure 9).

2.Place large openings of slots over screwheads. Slide heater down until screws are in small portion of slots.

Keyhole

Slots

Figure 9 - Location Of Keyhole Slots On Back Panel Of Heater

Removing Front Panel of Heater

1.Remove two screws near bottom cor- ners of front panel.

2.Lift straight up on grill guard until it stops. Grill guard will slide up about 1/4".

3.Pull bottom of front panel forward, then down.

Installing Bottom Mounting Screw

1.Locate bottom mounting hole. This hole is near bottom on back panel of heater (see Figure 11).

2.Mark screw location on wall.

3.Remove heater from wall.

4.If installing bottom mounting screw into hollow or solid wall, install wall anchor. Follow steps 1 through 5 un- der Attaching To Wall Anchor Method.

If installing bottom mounting screw into wall stud, drill hole at marked lo- cation using 9/64" drill bit.

5.Replace heater on wall.

6.Insert bottom anchor screw through back panel into bottom anchor or drilled hole (see Figure 11).

7.Tighten screw until heater is firmly se- cured to wall. Do not over tighten.

Note: Do not replace front panel at this time. Replace front panel after making gas connections and checking for leaks (see pages 9 and 10).

Figure 11 - Installing Bottom Mounting Screw

Figure 6 - Folding Anchor

Thin Walls (1/4" to 1/2" thick)

Figure 7 - Popping Open Anchor Wings

For Thin WallsFigure 10 - Removing Front Panel Of Heater

8

104276

Page 7 Page 9
Image 8
Page 7 Page 9
Contents OWNER’S Operation and Installation Manual What to do if YOU Smell GASSafety Information Natural GAS HeaterProduct Features Product IdentificationLocal Codes UnpackingAIR for Combustion and Ventilation Providing Adequate VentilationUnusually Tight Construction Confined and Unconfined SpaceDetermining if You Have a Confined or Unconfined Space AIR for Combustion VentilationDetermining FRESH-AIR Flow for Heater Location Ventilation Air From Outdoors Ventilation AIRVentilation Air From Inside Building Installation Installation ItemsInstalling Heater to Wall Check GAS TypeInstalling Two Mounting Screws Installing Bottom Mounting ScrewPlacing Heater on Mounting Screws Removing Front Panel of HeaterConnecting to GAS Supply Gas ConnectionFor Your Safety Read Before Lighting Pressure Testing Gas Supply Piping SystemPressure Testing Heater Gas Connections Operating HeaterManual Lighting Procedure Lighting InstructionsTo Select Heating Level To Turn OFF GAS To ApplianceCleaning and Maintenance Inspecting BurnerTroubleshooting Observed Problem Possible Cause RemedyTurn control knob until it locks at desired Observed Problem Possible Cause Specifications Replacement PartsTechnical Service Service HintsParts Centrals Baltimore Electric Washer Equipment Co Dayton HardwareTarantin Tank Co Heater and Fireplace Store Cans Unlimited, IncIllustrated Parts Breakdown CGN10RLAParts List KEY Part Number Description QTYWarranty Information

CGN10RLA specifications

Desa CGN10RLA is a cutting-edge generator that exemplifies modern engineering and design, making it a popular choice among residential and commercial users alike. This generator stands out for its reliability and efficiency, characteristics that are essential for those who require a consistent power supply in various situations, from home use during outages to outdoor recreational activities.

One of the main features of the Desa CGN10RLA is its robust engine, which delivers a powerful output of up to 10,000 watts. This high capacity makes it suitable for running heavy-duty appliances and tools. Whether you need to power your air conditioning unit during a summer heatwave or run multiple devices on a construction site, this generator has the power to meet your needs.

The CGN10RLA also boasts impressive fuel efficiency. Its advanced fuel management system allows for longer run times on a single tank, which is a significant advantage for users looking to minimize interruptions and maximize productivity. This generator is designed to accommodate a variety of fuel types, providing flexibility and convenience for users.

Equipped with a state-of-the-art inverter technology, the Desa CGN10RLA guarantees stable power output with less than 3% total harmonic distortion. This feature is particularly important for sensitive electronic devices, ensuring that they are safeguarded against power surges that could lead to damage. Thus, users can confidently run their office equipment, computers, and other delicate electronics without concern.

Portability is another highlight of the CGN10RLA. The generator is designed with integrated wheels and a folding handle, making it easy to transport. Its compact size means it can fit into tight storage spaces, while still providing ample power when needed.

In terms of safety, the Desa CGN10RLA incorporates several protective features such as low oil shutdown and overload protection, ensuring the safe operation of the unit. This generator is also equipped with a user-friendly control panel, allowing for straightforward operation and accessibility.

Overall, the Desa CGN10RLA is a versatile generator that combines power, efficiency, and convenience. Whether for home use, travel, or professional projects, its advanced technology and user-centric design make it an excellent choice for anyone in need of reliable power.
Top Page Image Contents