Desa CGP10RLA installation manual Continued, Air For Combustion And Ventilation

Page 5
Continued

OWNER’S MANUAL

AIR FOR

COMBUSTION AND

VENTILATION

Continued

DETERMINING FRESH-AIR FLOW FOR HEATER LOCATION

Determining if You Have a Confined or Unconfined Space

Use this worksheet to determine if you have a confined or unconfined space.

Space: Includes the room in which you will install heater plus any adjoining rooms with doorless passageways or ventilation grills between the rooms.

1.Determine the volume of the space (length x width x height).

Length x Width x Height = _________________ cu. ft. (volume of space)

Example: Space size 18 ft. (length) x 16 ft. (width) x 8 ft. (ceiling height) = 2304 cu. ft. (volume of space)

If additional ventilation to adjoining room is supplied with grills or openings, add the volume of these rooms to the total volume of the space.

2.Divide the space volume by 50 cubic feet to determine the maximum Btu/Hr the space can support.

_________________ (volume of space) ÷ 50 cu. ft. = (Maximum Btu/Hr the space can support)

Example: 2304 cu. ft. (volume of space) ÷ 50 cu. ft. = 46.1 or 46,100 (maximum Btu/Hr the space can support)

3.Add the Btu/Hr of all fuel burning appliances in the space.

Vent-free heater

__________________ Btu/Hr

 

 

 

 

Gas water heater*

__________________ Btu/Hr

Example:

 

40,000

 

Gas furnace

__________________ Btu/Hr

Gas water heater

 

Btu/Hr

Vented gas heater

__________________ Btu/Hr

Vent-free heater

+

10,000

Btu/Hr

Total

=

50,000

Btu/Hr

Gas fireplace logs

__________________ Btu/Hr

 

 

 

 

Other gas appliances* + __________________ Btu/Hr

 

 

 

 

Total

= __________________ Btu/Hr

 

 

 

 

*Do not include direct-vent gas appliances. Direct-vent draws combustion air from the outdoors and vents to the outdoors.

4.Compare the maximum Btu/Hr the space can support with the actual amount of Btu/Hr used.

_________________ Btu/Hr (maximum the space can support)

_________________ Btu/Hr (actual amount of Btu/Hr used)

Example: 46,100 Btu/Hr (maximum the space can support) 50,000 Btu/Hr (actual amount of Btu/Hr used)

The space in the above example is a confined space because the actual Btu/Hr used is more than the maximum Btu/Hr the space can support. You must provide additional fresh air. Your options are as follows:

A.Rework worksheet, adding the space of an adjoining room. If the extra space provides an unconfined space, remove door to adjoin- ing room or add ventilation grills between rooms. See Ventilation Air From Inside Building, page 6.

B.Vent room directly to the outdoors. See Ventilation Air From Outdoors, page 6.

C.Install a lower Btu/Hr heater, if lower Btu/Hr size makes room unconfined.

If the actual Btu/Hr used is less than the maximum Btu/Hr the space can support, the space is an unconfined space. You will need no additional fresh air ventilation.

DETERMINING FRESH-AIR FLOW FOR HEATER LOCATIONWARNING: If the area in which the heater may be operated is smaller than that defined as an unconfined space or if the building is of unusually tight construction, provide adequate combustion and ventilation air by one of the methods described in the National Fuel Gas Code, ANS Z223.1, Section 5.3 or applicable local codes.

Continued

104275

5

Image 5
Contents INFRARED VENT-FREEPROPANE/LP GAS HEATER OWNER’S OPERATION AND INSTALLATION MANUALCGP10RLA PROPANE/LP GAS HEATER SAFETY INFORMATIONPRODUCT IDENTIFICATION PRODUCT FEATURESLOCAL CODES UNPACKINGPROVIDING ADEQUATE VENTILATION AIR FOR COMBUSTION AND VENTILATIONPROPANE/LP GAS HEATER DETERMINING FRESH-AIRFLOW FOR HEATER LOCATION ContinuedAIR FOR COMBUSTION AND VENTILATION AIR FOR COMBUSTION AND VENTILATION PROPANE/LP GAS HEATERContinued Figure 2 - Ventilation Air from Inside BuildingINSTALLATION ITEMS INSTALLATIONINSTALLING HEATER TO WALL CHECK GAS TYPEInstalling Two Mounting Screws INSTALLATIONInstalling Bottom Mounting Screw PROPANE/LP GAS HEATERCONNECTING TO GAS SUPPLY INSTALLATIONContinued Figure 13 - Gas ConnectionINSTALLATION OPERATING HEATERFOR YOUR SAFETY READ BEFORE LIGHTING PROPANE/LP GAS HEATEROPERATING HEATER MANUAL LIGHTING PROCEDUREContinued LIGHTING INSTRUCTIONSINSPECTING BURNER CLEANING AND MAINTENANCECLEANING BURNER PILOT AIR INLET HOLE PROPANE/LP GAS HEATEROBSERVED PROBLEM TROUBLESHOOTINGPOSSIBLE CAUSE REMEDYOBSERVEDPROBLEM TROUBLESHOOTINGPROPANE/LP GAS HEATER ContinuedMaintenance, page TROUBLESHOOTINGContinued Refer to Air for Combustion and VentiREPLACEMENT PARTS SPECIFICATIONSTECHNICAL SERVICE SERVICE HINTSPARTS CENTRALS PROPANE/LP GAS HEATER ILLUSTRATED PARTS BREAKDOWNPART PARTS LISTNUMBER DESCRIPTIONINTERNATIONAL WARRANTY INFORMATIONNOT A UPC Model