Desa TT15A 10, TT30 10, SPC-15R owner manual Assembly Instructions, 30,000 BTU Models only

Page 4

SAFETY INFORMATION

Continued

15.Install the heater such that it is not directly exposed to water spray, rain, dripping water and/or wind.

16.Operate only on a stable, level surface.

17.Due to the high surface and exhaust tempera- tures, adults and children must observe clear- ances to avoid burns or clothing ignition.

18.Do not move, handle or service while hot or burning. Do not attach or remove a hot or operating heater from the propane/LP tank.

19.Before each use, check heater for leaks. Never use an open flame to check for leaks. Apply a mixture of liquid soap and water to all joints. Bubbles forming show a leak. Correct all leaks.

20.Keep all connections and fittings clean. Make sure propane/LP tank valve is clean. Check "O" ring on heater inlet fuel valve connector for damage before each use. Replace if worn or damaged.

21.Use only in accordance with local codes or, in the absence of local codes, with the Standard for the Storage and Handling of Liquefied Pe- troleum Gases ANSI/NFPA 58 and CSA B149.1, Natural Gas and Propane Installation Code.

ASSEMBLY

INSTRUCTIONS

30,000 BTU MODELS ONLY

1.Inspect the heater components for possible shipping damage. If any is found, immediately notify the dealer. Check to make sure that all components are included with your heater (see pages 8 and 9).

2.Insert the piezo ignitor into the bracket on the burner support bracket as shown in Figure 1. Tighten the piezo mounting nut. Do not over tighten the nut.

3.Connect the burner hoses together as shown in Figure 2. Wrench tighten to insure leak tight connection.

4.Mount the burner assembly onto the support arm using the burner head mounting brackets and brass screws as shown in Figure 3. Place side of bracket into the slot on support arm. Secure with screw. Make certain that the air holes on the sides of the burner tube are not blocked. Securely tighten the burners into place.

5.Attach the electrode wires to the piezo ignitor as shown in Figure 4.

Piezo Ignitor

Piezo

Mounting

Nut

Burner

Support

Bracket

Figure 1 - Installing Piezo Ignitor

Figure 2 - Attaching Burner Hoses to

Regulator

Burner Head

Assembly

Slot

Support

Arm

 

 

Air Hole

Brass Screw

Burner Head

Mounting Bracket

 

Figure 3 - Attaching Burner Head

Assembly to Support Arm

Piezo Ignitor

Electrode Wires

Figure 4 - Attaching Electrode Wires to Piezo Ignitor

4

www.desatech.com

113973-01A

Page 3 Page 5
Image 4
Page 3 Page 5
Contents Carbon Monoxide Hazard For Your SafetyModels Specifications Table of ContentsGeneral Hazard Warning Safety Information Asphyxiation HazardAssembly Instructions 30,000 BTU Models onlyOperating Instructions To Start HeaterTo Stop Heater Maintenance StorageTo Restart Heater Technical Service Replacement PartsParts Under Warranty Parts not Under WarrantyIllustrated Parts Breakdown Parts List Warranty and Repair Service Keep this WarrantyAdvertencia Para SU SeguridadModelos Tabla DE Contenido Advertencia General DE PeligroEspecificaciones Información DE Seguridad Peligro DE AsfixiaInstrucciones DE Ensamblaje Sólo Para Modelos DE 30.000 BTUInstrucciones DE Funcionamiento Para Encender EL CalentadorPara Apagar EL Calentador Para Volver a Encender EL CalentadorReparaciones Servicio TécnicoPiezas DE Repuesto Piezas CON GarantíaClasificación Ilustrada DE Piezas Lista DE Piezas Garantía Y Servicio DE Reparación Guarde Esta GarantíaRisque D’EMPOISONNEMENT AU Monoxyde DE Carbone ModèlesTT15A AvertissementTable DES Matières Avertissement DE Risque GénéralSpécifications LA Sécurité Risque D’ASPHYXIEInstructions ’ASSEMBLAGE Modèles À 30 000 BTU UniquementPour Allumer L’APPAREIL DE Chauffage Fixez fermement tous les raccords de gazPour Arrêter L’APPAREIL DE Chauffage Entretien ET EntreposagePour Redémarrer L’APPAREIL DE Chauffage Service Technique RéparationPièces DE Rechange Pièces Sous GarantieVUE Détaillée DES Pièces Liste DES Pièces 113973-01A 113973-01A Service DE Garantie ET DE Réparation Conservez Cette Garantie

SPC-15R, TT15A 10, TT30 10 specifications

Desa TT30 10, TT15A 10, and SPC-15R are innovative products in the realm of industrial tools and equipment, designed to optimize performance, efficiency, and user experience. Each model embodies cutting-edge technology and thoughtful engineering tailored to meet the demands of modern operations.

The Desa TT30 10 is a versatile tool engineered for heavy-duty performance. This model is equipped with a robust motor that delivers high torque, making it suitable for a variety of applications, from manufacturing to construction. Its user-friendly interface includes an ergonomic handle that minimizes fatigue during prolonged use. Additionally, the TT30 10 features an advanced cooling system, which prevents overheating and prolongs the lifespan of the equipment, ensuring it can handle extended work sessions without compromising performance.

On the other hand, the Desa TT15A 10 is recognized for its compact design and lightweight structure, making it an excellent option for those looking for portability without sacrificing strength. This model is particularly advantageous for smaller projects or tight workspaces. The TT15A 10 incorporates a unique vibration-damping technology, which drastically reduces vibrations during operation, leading to enhanced accuracy and comfort. This feature is especially beneficial for precision tasks, allowing users to work more effectively over longer periods.

Meanwhile, the SPC-15R stands out due to its advanced technological integration. This model is equipped with smart features such as real-time monitoring and diagnostics, allowing users to track performance metrics and receive alerts about maintenance needs. The SPC-15R also has a built-in energy-efficient motor that not only conserves power but also reduces operational costs, making it an eco-friendly choice for businesses. Its durable construction, combined with high-quality materials, ensures reliability and longevity, even in the most challenging environments.

Collectively, Desa TT30 10, TT15A 10, and SPC-15R represent a commitment to innovation and excellence in industrial tools. Each model incorporates features and technologies that cater to diverse operational requirements, emphasizing efficiency, durability, and user comfort. Whether for heavy-duty applications or precision tasks, these models provide solutions that meet the varying needs of industries today. As companies continue to seek out tools that enhance productivity while maintaining usability, these Desa models exemplify the future of industrial equipment.
Top Page Image Contents