Desa VP16A, VN18A, VP26A Installing Bottom Mounting Screws, Placing Heater On Mounting Bracket

Page 10

INSTALLATION

Continued

2.Fold wall anchor as shown in Figure 9.

3.Insert wall anchor (wings first) into hole. Tap anchor flush to wall.

4.For thin walls (1/2" or less), insert red key into wall anchor. Push red key to “pop” open anchor wings.

IMPORTANT: Do not hammer key!

For thick walls (over 1/2" thick) or solid walls, do not pop open wings.

5.Place mounting bracket onto wall. Line up last hole on each end of bracket with wall anchors.

6.Insert mounting screws through bracket and into wall anchors.

7.Tighten screws until mounting bracket is firmly fastened to wall.

Figure 9 - Folding Anchor

Installing Bottom Mounting Screws

1.Locate two bottom mounting holes. These holes are near bottom on back panel of heater (see Figure 12).

2.Mark screw locations on wall.

3.Remove heater from mounting bracket.

4.If installing bottom mounting screws into hollow or solid wall, install wall anchors. Follow steps 1 through 4 under Attaching To Wall Anchor Method, page 9.

If installing bottom mounting screw into wall stud, drill holes at marked locations using 9/64" drill bit.

5.Replace heater onto mounting bracket.

6.Place spacers between bottom mounting holes and wall anchor or drilled hole.

7.Hold spacer in place with one hand. With other hand, insert mounting screw through bottom mounting hole and spacer. Place tip of screw in opening of wall anchor or drilled hole.

8.Tighten both screws until heater is firmly secured to wall. Do not over tighten.

Note: Do not replace front panel at this time. Replace front panel after making gas connec- tions and checking for leaks (see pages 12 and 13).

Figure 10 - Popping Open Anchor Wings

For Thin Walls

Placing Heater On Mounting Bracket

1.Locate two horizontal slots on back panel of heater.

2.Place heater onto mounting bracket. Slide horizontal slots onto stand-out tabs on mount- ing bracket.

Horizontal Slots

Front View

Wall Heater

Stand-Out Tab

Mounting Bracket (attached to wall)

Spacer

Side View

Figure 12 - Installing Bottom Mounting Screws

Figure 11 - Mounting Heater Onto

Mounting Bracket

10

www.desatech.com

113052-01D

Page 9 Page 11
Image 10
Page 9 Page 11
Contents VN30A, VN30TA, VP16ITA, VP22ITA Model VN30A ShownTable of Contents Safety Information Local Codes Product FeaturesUnpacking Providing Adequate Ventilation AIR for Combustion VentilationDetermining FRESH-AIR Flow for Heater Location Ventilation AIR Ventilation Air From Inside BuildingCheck GAS Type InstallationInstallation Items Locating HeaterThermostat Models Only Installing Heater to WallThermostat Sensing Bulb Mounting Bracket5 Plaque Heaters Methods For Attaching Mounting Bracket To WallMarking Screw Locations Plaque HeaterInstalling Bottom Mounting Screws Placing Heater On Mounting BracketMounting Heater to Floor Connecting to GAS SupplyMounting Base Feet to Floor Where required by local code Mounting Base Feet to HeaterNatural Gas Checking GAS ConnectionsPropane/LP Test Pressures In Excess Of 1/2 Psig 3.5 kPa Test Pressures Equal To or Less Than 1/2 Psig 3.5 kPaOperating Heater NON-THERMOSTAT Models For Your Safety Read Before LightingLighting Instructions To Select Heating Level Manual Lighting ProcedureThermostat Models For Your Safety Read Before Lighting To Turn OFF GAS To ApplianceTurn thermostat control knob counter If pilot does not lightIgnitor Button Control Knob Plaque Thermostat OperationShutting Off Heater Pilot Flame Pattern Inspecting HeaterBurner Flame Pattern Burner Pilot AIR Inlet Cleaning MaintenanceODS/PILOT and Burner CabinetTroubleshooting Observed Problem Possible Cause RemedyODS/pilot lights but flame When heated, vapors from Gas leak. See WarningSpecifications Illustrated Parts Breakdown Parts List Cabinet Body Models VP16ITA and VP22ITA KEY Part Number VP16ITA VP22ITA Description QTY Illustrated Parts Breakdown and Parts List Burner Assembly Models VP16A and VN18ABurner Assembly Models VP26A and VN30A ODS/Pilot Burner Assembly VP26A, VN30ABurner Assembly Models VP16ITA and VP22ITA Burner Assembly VP22ITA Burner Assembly VP16ITABurner Assembly Models VP16TA, VN18TA, VP26TA and VN30TA Technical Service Replacement PartsService Publications Service Hints Parts Under WarrantyFAN Kits GA3250T AccessoriesParts Central Equipment Shutoff Valve GA5010113052-01D 113052-01D Keep this Warranty Warranty InformationLimited Warranty Vanguard VENT-FREE Infrared GAS Heaters
Top Page Image Contents