Desa GWP20T Mounting Heater to Floor with Optional Floor KIT, Installing Bottom Mounting Screws

Page 11

INSTALLATION

Continued

Installing Bottom Mounting Screws

1.Locate two bottom mounting holes. These holes are near bottom on back panel of heater (see Figure 12).

2.Mark screw locations on wall.

3.Remove heater from mounting bracket.

4.If installing bottom mounting screws into hol- low or solid wall, install wall anchors. Fol- low steps 1 through 4 under Attaching To Wall Anchor Method, page 10.

If installing bottom mounting screw into wall stud, drill holes at marked locations using 9/64" drill bit.

5.Replace heater onto mounting bracket.

6.Place spacers between bottom mounting holes and wall anchor or drilled hole.

7.Hold spacer in place with one hand. With other hand, insert mounting screw through bottom mounting hole and spacer. Place tip of screw in opening of wall anchor or drilled hole.

8.Tighten both screws until heater is firmly se- cured to wall. Do not over tighten.

Note: Do not replace front panel at this time. Replace front panel after making gas con- nections and checking for leaks (see pages 12 through 14).

Front View

Heater

Wall

 

 

Spacer

Side View

Figure 12 - Installing Bottom Mounting

Screws

MOUNTING HEATER TO FLOOR WITH OPTIONAL FLOOR KIT

Mounting Base Feet to Heater

1.Lay heater cabinet on its back on a table with the heater bottom overhanging the table edge.

2.Align holes in base foot with mounting holes on bottom of cabinet (see Figure 13).

3.Secure base foot to heater using sheet metal screws.

4.Repeat for other side.

Wood

Screw

Base Foot

Sheet Metal Screw

Figure 13 - Installing Base Feet

Mounting Base Feet to Floor (Where required by local code)

1.Remove front panel (see Removing Front Panel of Heater, page 9).

2.Position heater with base feet in desired loca- tion. Mark holes for drilling. Remove heater with base.

3.For carpeted floors, make a small cut with a sharp knife at marked locations prior to drill- ing. If mounting base to a wood floor, drill 1/8 inch diameter hole, 3/4 inch deep. (Do not use anchors in wood floors).

If mounting base to a concrete floor, drill with 1/4 inch diameter concrete drill bit, 13/8 inches into floor. Insert anchors completely into holes.

4.Reposition heater with base feet over holes. Secure base to floor with wood screws. See Figure 13.

107884-01H

www.desatech.com

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents What to do if YOU Smell GAS Table of Contents Safety Information Unpacking Product FeaturesLocal Codes Product IdentificationConfined and Unconfined Space AIR for Combustion VentilationProviding Adequate Ventilation Unusually Tight ConstructionDetermining if You Have a Confined or Unconfined Space Determining FRESH-AIR Flow for Heater LocationVentilation Air From Inside Building InstallationVentilation AIR Check GAS TypeLocating Heater Installation ItemsInstalling Heater to Wall Placing Heater On Mounting Bracket 20,000 Btu/Hr ModelsAttaching To Wall Anchor Method Mounting Base Feet to Heater Installing Bottom Mounting ScrewsMounting Base Feet to Floor Where required by local code Mounting Heater to Floor with Optional Floor KITTypical Inlet Pipe Diameters Connecting to GAS SupplyPropane/LP Checking GAS ConnectionsNatural Gas Open equipment shutoff valve see , Pressure Testing Heater Gas ConnectionsLighting Instructions Manual Control Models For Your Safety Read Before LightingOperating Heater Shutting Off Burner Only pilot stays lit Manual Lighting ProcedureTo Turn OFF GAS To Appliance Shutting Off HeaterThermostat Control Operation Burner Flame Pattern Inpecting HeaterPilot Flame Pattern Cabinet Cleaning MaintenanceODS/PILOT and Burner Burner Pilot AIR InletObserved Problem Possible Cause Remedy TroubleshootingReplace burner orifice See Cleaning and Mainte Statement above Gas leak. See WarningGP30, GP30T SpecificationsGN30, GN30T WMN20, GWN20 Parts Under Warranty Service HintsTechnical Service Service Publications Replacement PartsIllustrated Parts Breakdown NJF 8C Parts ListGWN20T, GWP20T GWN30T, GWP30T Parts List Base KIT GA4550 AccessoriesEquipment Shutoff Valve GA5010 FAN Kits GA3250TParts Centrals Limited Warranty VENT-FREE Residential GAS Heaters Warranty InformationKeep this Warranty

GP30, GWN20T, GWN30T, GWN20, GWP20 specifications

Desa GWP20, GWP30T, GP30T, GN30T, and GP30 are advanced water heater models that stand out in the market for their efficiency, innovative technology, and user-friendly features. Each model is designed to cater to different consumer needs, offering reliable hot water solutions for residential and commercial applications.

The Desa GWP20 is a compact and efficient water heater that operates on a 20-gallon tank. Ideal for smaller households, it boasts fast heating capabilities and a durable construction that ensures longevity. Its user-friendly control panel allows for easy temperature adjustments, and its energy-saving mode helps reduce utility costs.

Moving up in capacity, the GWP30T features a 30-gallon tank, making it suitable for medium-sized households. This model incorporates a high-efficiency burner that maximizes heat output while minimizing gas consumption. With an upgraded insulation system, the GWP30T retains heat for longer periods, enhancing energy efficiency. The built-in diagnostics monitor performance, ensuring consistent operation and alerting users to any potential issues.

The GP30T is another 30-gallon model that emphasizes flexible installation options. It can be configured for various venting systems, making it adaptable for different home layouts. Its robust safety features, such as an automatic shut-off system, provide peace of mind for users. Additionally, the GP30T is equipped with a flame sensor for improved safety during operation.

For those seeking an efficient gas-powered unit, the GN30T delivers exceptional performance with a 30-gallon capacity. This model is designed to withstand the demands of larger households, featuring rapid recovery rates to provide a continuous supply of hot water. It utilizes advanced combustion technology that ensures efficient gas usage, striking the perfect balance between performance and energy costs.

Finally, the GP30 is a versatile water heater designed to meet diverse consumer needs. With a focus on sustainability, this model incorporates eco-friendly materials and technologies. The GP30 is packed with features that enhance its usability, such as customizable temperature settings, easy-to-read indicators, and a straightforward installation process.

In summary, Desa's GWP20, GWP30T, GP30T, GN30T, and GP30 water heaters are engineered for efficiency and reliability. Each model offers unique features tailored to specific user needs, from compact designs for smaller spaces to powerful systems for larger families. With an emphasis on modern technology and safety, Desa continues to be a leader in the water heating market.
Top Page Image Contents