PVI Industries 180, 150 manual Standard Features and Equipment

Page 6

2 STANDARD FEATURES AND EQUIPMENT

2.1Performance

−95% thermal efficiency at full fire from 40° to 140°F

−Up to 99% thermal efficiency with modulation

−< 20 ppm NOx

−Ducts direct combustion air up to 100 equivalent feet through 6-inch diameter material (requires UL approved vent cap, see optional equipment list)

−Vents up to 100 equivalent feet through 6-inch diameter material

2.2Pressure Vessel

−AquaPLEX® tank (unlined duplex alloy)

−Storage tank ASME stamped and National Board registered for 150 psi MAWP

−Nonferrous, removable fittings at all tank connections

−Hand hole cleanout

−Fiberglass insulation

−Steel jacket panels with industrial-grade finish

−Drain valve

2.3Heat Exchanger

−Three-pass, fire tube design

−AquaPLEX® fire tubes

−Secondary economizer for low temperature flue gas

2.4Codes And Standards

−Intertek / ETL listed to US and Canadian safety standards

−Intertek / ETL listed for use with CPVC vent material (SANI models require listed Cat IV SS vent)

−Intertek / ETL certified as low-lead compliant

−FM compliant

−ASHRAE 90.1 compliant

2.5Burner, Operating Controls & Safeties

−Pre-mix surface burner with self-adjusting, proportionate gas/air ratio

−UL 795 compliant gas train

−Electronic flame safeguard with pre- and post-purge

−Combustion sequence panel lights including lockout

−Programmable electronic operating control with digital temperature readouts, adjustable from 70°F to 180°F

−Immersion temperature limiting device (high limit control)

−ASME-rated temperature and pressure relief valve

−NEMA-1 control enclosure

−Terminals for remote on-off

−Flame failure audible alarm and indicating light with remote contacts

−Seamless VFD modulation with 10-to-1 turndown

2.6Warranty and Service Policy (see warranty or service policy for details)

−10-Year tank warranty (PV 627)

−3-Year scale failure warranty (PV 563)

−First-year cost-free service policy (PV 551)

−10-Year chloride-induced stress corrosion cracking warranty (PV 8083)

2.7Miscellaneous

−Factory authorized startup

−Vent termination cap, 6-inch diameter (larger cap optional)

−Factory-equipped for connection to direct inlet air (requires UL listed vent termination cap, see options list)

−Condensate “P” trap (provided for field installation)

−Direct inlet air filter

6

PV500-46U 06/12

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Installation & Maintenance Manual Table of Contents Temptrac Electronic Controller Panel Operating and Safety ControlsTroubleshooting Guide Replacement Parts Remote Connections Terminal StripSafety Considerations Product Safety InformationBelow scalding temperatures Standard Features and Equipment Series Series Codes Water Heater InstallationChecking Equipment Before You Install Electrical RequirementsGeneral Piping Guidelines Service ClearancesClearances To Combustible Surfaces Inlet and Outlet ConnectionsPV500-46U 06/12 PV500-46U 06/12 Optional Condensate Neutralization System Inlet Pressure NAT. GAS Single Unit Installation Suggested Pipe SizeGAS Supply and Piping Convert Fittings to Equivalent Straight PipeInches Multiple Unit Installations GAS Piping Size ChartNominal Iron Length of Pipe in Straight Feet Appliance Isolation during Gas Supply Piping Pressure Test∙ All Air From Outdoors Combustion and Ventilation AIREquipment Located In Confined Spaces ∙ All Air From Inside The BuildingDuct Fitting Equivalent Length Duct Pipe Vertical or Horizontal Remote Air Duct TerminationVenting Venting the Power VT Plus Sani modelsVenting the Power VT Plus Maximum Category IV Vent Length Equivalent LengthVent Fitting Equivalent Length Vent Pipe Vertical or Horizontal Vent Termination Combining Category IV VentsOperating and Safety Controls Temperature and Pressure Relief ValvesHigh Water Temperature Limit Control Cathodic ProtectionElectronic Low Water Cut-Off Optional Down Temptrac Electronic Controller PanelSET ClockTo View The Setpoint To Change The SetpointTo Change Other Parameters LED Display Alarm Messages Alarm Cause Results of Alarm Condition MessageRecommended Action Remote Connections Terminal Strip Loss of Flame Signal Sequence of OperationIncoming 120VAC LED Indication Fault Mode OFFInitial Startup Turn-on main gas shutoff valve PV500-46U 06/12 Gas Train Illustration Alternate Gas Train IllustrationTroubleshooting Guide Problem Probable Cause Corrective ActionReplacement Parts Replacement PartsControl Panel Contact factory for more information Burner Assembly Optional components may or may not be shown Burner Assembly Components SUPPORT, GAS Train FB14 PvifBurner GAS Train Components Contact factory for more informationPeriodic Maintenance PV500-46U 06/12 Recommended Maintenance Schedule PV500-46U 06/12 PV500-46U 06/12

150, 180 specifications

PVI Industries has established itself as a prominent manufacturer in the water heating industry, particularly known for its range of commercial water heaters. Among their well-regarded products is the PVI Industries 150,180, a robust unit engineered to meet the demanding needs of various commercial applications.

The PVI Industries 150,180 is designed to deliver high-efficiency performance, catering primarily to large-scale operations such as hotels, hospitals, and other facilities that require a constant supply of hot water. The unit boasts impressive heating capacity, enabling it to serve multiple points of use simultaneously. With a focus on reliability and durability, the construction of the 150,180 incorporates high-quality materials that ensure longevity even in the most challenging environments.

One of the standout features of the PVI 150,180 is its advanced heating technology. The unit utilizes a state-of-the-art gas-fired burner system, which not only ensures rapid heating but also maximizes energy efficiency. This attention to energy performance is crucial for businesses aiming to reduce operational costs and minimize their environmental impact. Furthermore, the unit supports a range of fuel types, including natural gas and propane, providing flexibility for different regional needs and preferences.

From a technological standpoint, the PVI Industries 150,180 includes an intuitive control system that allows users to monitor and adjust settings easily. This sophisticated interface provides real-time data on water temperature, operational status, and maintenance alerts, significantly enhancing user experience and system management.

Safety features are paramount in PVI’s design philosophy. The 150,180 comes equipped with multiple safety mechanisms, including a high-temperature limit switch and a pressure relief valve, ensuring safe operation and compliance with strict industry regulations.

In terms of installation, the PVI Industries 150,180 is engineered with versatility in mind. It can be installed in various configurations, making it adaptable to the spatial constraints of any facility. Maintenance is straightforward, with accessible components designed to reduce downtime and service costs.

Overall, the PVI Industries 150,180 represents a leading choice for commercial water heating solutions, characterized by its efficiency, reliability, and advanced technology, meeting the diverse needs of modern businesses while upholding the highest standards of safety and performance.
Top Page Image Contents