Feed Trim Adjustment

B. In the LOW position, the EASYFIRE will be feeding approxim ately 1 to 1½ lbs. of pellets per hour and the flam e will fluctuate between 1" and 6" in height.

C. In the MEDIUM position the EASYFIRE will be feeding approxim ately three (3) pounds of pellets per hour and the flam e will fluctuate between 3" and 8" of fire.

D. In the HIGH position the EASYFIRE will be feeding approxim ately 4+ lbs. per hour and the flam e will fluctuate between 3" and a full flam e. The fan speed will increase accordingly as the heater autom atically adjusts itself based on tem perature inside the heater.

E.The CLEAN position is to be used only when the heater is not burning and you wish to clean out the accumulated ash in the front of the fire area. See CLEAN OUT section of maintenance instructions.

F. After the heater is running for several hours and you wish to turn it off sim ply press the button to OFF. The heater will continue running until it cools down and then will automatically shut itself down.

G. REMEMBER: Each feed position will fluctuate because the microprocessor is autom atically adjusting the feed and air based on tem perature. This means the pellet feed rate and flam e height will change accordingly based on quality of pellet and heat loss of dwelling.

3.Starting the Stove: Push a Heat Range button (Low or Medium is best for start up) (Figure 13) and turn the therm ostat up to “Call for heat”. The stove fan will begin to operate along with the ignitor cycle. After about a minute the pellets will begin to fall in the burn pot. After five

m inutes there will be a fire in the burn pot and the stove will begin to heat up. W hen the stove reaches start up operating tem perature it will then switch to the control panel setting and begin it’s autom atic operation cycle.

Figure 13

Prior to stove operating on thermostat, confirm proper operation by servicing and adjusting the stove as outlined in the “Installation Guide”. When servicing stove, operate with thermostat bypassed as stove will reset to start up mode each time thermostat is activated.

Underneath the control button you will find a small round button that will turn forward and reverse. This button can adjust the feed m otor in the LOW operating position. By turning the button clockwise you can increase the feed on LOW and by turning it counterclockwise you can decrease the feed in the LOW position. Factory setting is 9:00 o’clock.

Once the stove is at operating temperature for one hour set the stove on LOW . Adjust the trim button so that average flame is approx. 1-2" above the burn pot. This will set the average feed rate (air/flue) for best operation.

Move this button carefully! It is designed to fine tune your LOW setting in the event you change brands of pellets and/or live at a higher elevation. If this setting is to low the stove may go out during LOW setting operations. If this should happen increase the trim by sm all am ount.

MATCH LIGHT FIRE AND START-UP

1.Filling the Hopper and Start-Up:

CAUTION: FUEL HOPPER LID MUST BE CLOSED BEFORE OPERATING UNIT. MAINTAIN HOPPER SEAL IN GOOD CONDITION. DO NOT OVERFILL HOPPER! THE EASYFIRE WILL HOLD ABOUT 60 LBS. OF PELLETS.

Open the top lid and fill the hopper with pellets (Figure 11).

Make sure hopper lid is fully closed. Open the front door and fill the burn pot with a hand full of pellets.

Figure 14

IMPORTANT: The fire pot must be seated flush and m ust sit even in the pot tray. Air leaking around the fire pot will create a poor burn (Figure 14). Light the pellets in Fire Pot using any approved pellet fuel starter.

Allow pellets to burn for approxim ately 1 minute, or until pellet ignition has been achieved. Close door and turn the control knob to the "FAN" position. Allow fire to burn for several minutes. W hen the pellets are well lit, turn the control knob to "LOW" for approxim ately 10 m inutes then turn up to "HI". W e recomm end that you run the heater on “Medium ” or "HI" for about 30 m inutes in order to get the

EF5001U specifications

The Sierra Products EF5001U is a versatile and powerful electronic appliance designed for both home and industrial use. Known for its robust construction and innovative features, this model stands out in its category, providing users with unmatched efficiency and reliability.

One of the main features of the EF5001U is its impressive power output. With a maximum performance of 5000 watts, this appliance is capable of handling a wide range of tasks, from powering tools to supporting multiple devices simultaneously. This makes it ideal for both professional contractors and DIY enthusiasts who demand high-performance equipment.

The EF5001U integrates advanced inverter technology, which helps to deliver a clean and stable power supply. This technology is crucial for sensitive electronic devices, ensuring they operate safely without the risk of voltage spikes or surges. Additionally, the inverter allows for more efficient fuel consumption, leading to longer operational times between refueling, making it a cost-effective choice for extended use.

Portability is another key characteristic of the Sierra Products EF5001U. This model features a lightweight design complemented by integrated handles, allowing for easy transport and convenient storage. Whether you need it for outdoor activities, road trips, or emergency backup power, its portability ensures that it can accompany you anywhere.

Safety features are also a priority with the EF5001U. It comes equipped with automatic shut-off mechanisms that activate in the event of low oil levels or overheating, protecting both the unit and its users. Furthermore, the durable construction and weather-resistant materials ensure that the EF5001U can withstand harsh conditions, making it a reliable choice for various environments.

User-friendly controls and indicators simplify operation, allowing even individuals with minimal technical experience to use the unit effectively. The intuitive interface provides clear information about operational status, making it easy for users to monitor performance at a glance.

In conclusion, the Sierra Products EF5001U is a top-of-the-line electronic appliance that combines power, efficiency, and portability. With its advanced inverter technology, robust safety features, and easy-to-use design, it is well-suited for a wide range of applications, making it an excellent investment for anyone in need of reliable power solutions. Whether at home or on the job, the EF5001U is engineered to meet and exceed expectations.