Indoor Fireplace Installation Manual for Napoleon Fireplaces

5.Remove nails from the shingles, above and to the sides of the chimney. Place the flashing over the air termi- nal and slide it underneath the sides and upper edge of the shingles. Ensure that the air terminal is properly centred within the flashing, giving a 3/4" margin all around. Fasten to the roof. Do not nail through the lower portion of the flashing. Make weather-tight by sealing with caulking. Where possible, cover the sides and top edges of the flashing with roofing material.

6.Apply a heavy bead of weatherproof caulking 2 inches above the flashing. Slide the storm collar around the air terminal and down to the caulking. Tighten to ensure that a weather-tight seal between the air terminal and the collar is achieved. Attach the other storm collar centred between the air intake and the air exhaust slots onto the air terminal. Tighten securely. Attach the vertical rain cap.

Spacers are at- tached to the 4" inner flex liner at predeter- mined intervals to maintain a 1-1/4" air gap to the 7" outer liner. These spacers

must not be removed. FIGURE 31

7.If more liner needs to be used to reach the fireplace, couple them together as illustrated. The vent system must be supported approximately every 3 feet for both vertical and horizontal runs. Use noncombustible strapping to maintain a clearance to combustibles of 1".

FIREPLACE VENT CONNECTION

1.Install the 4 inch diameter aluminium flexible liner to the fireplace. Secure with 3 screws and flat washers. Seal the joint and screw holes using the high temperature seal- ant provided.

2.Install the 7 inch diameter aluminium flexible liner to the fireplace. Attach and seal the joints.

FIGURE 32

USING RIGID VENT COMPONENTS

The vent system must be supported approximately every 3 feet for both vertical and horizontal runs. Use Wolf Steel vent spacers W615-0033or equivalent every 3 feet and either side of each elbow to maintain the minimum 1¼" clearance between the outer and inner vent pipes. Use Wolf Steel support ring assembly W010-0370or equiva- lent noncombustible strapping to maintain the minimum clearance to combustibles for both vertical and horizontal runs.

HORIZONTAL AIR TERMINAL INSTALLATION

FIGURE 33

1.Move the fireplace into po- sition. Measure the vent length required between terminal and fireplace taking into account the

additional length needed for the finished wall surface and any 1¼" overlaps between venting components.

2.Apply high temperature sealant to the outer edge of the 4" inner collar of the fireplace. Attach the first vent component and secure using 3 self tapping screws. Repeat using 7" piping.

3.Holding the air terminal (lettering in an upright, readable position), insert into both vent pipes with a twisting motion to ensure that both the terminal sleeves engage into the vent pipes and sealant. Secure the terminal to the exterior wall and make weather tight by sealing with caulking (not supplied).

The air terminal mounting plate may be recessed into the exterior wall or siding by 1½", the depth of the return flange.

EXTENDED HORIZONTAL AND CORNER

AIR TERMINAL INSTALLATION

1.Follow the instructions for "Horizontal Air Terminal In- stallations", items 1 to 3.

2.Continue adding components alternating inner and outer venting. Ensure that all 4" venting and elbows have sufficient vent spacers attached and each component is securely fastened to the one prior. Attach the 4" telescopic

sleeve to the vent run.	AIR TERMINAL	FIGURE 34
Repeat using a 7" tel-	TELESCOPIC SLEEVE
escopic sleeve. Secure	TELESCOPIC SLEEVE
escopic sleeve. Secure
and seal as before. To	20"
facilitate completion, at-	20"
tach 4" and 7" couplers	COUPLER
tach 4" and 7" couplers
to the air terminal.		VENTING

3.Install the air terminal. See item 3 of the Horizontal Air Terminal Installation. Extend the 4" telescopic sleeve; connect

to the air terminal assembly. Fasten with self tapping screws and seal. Repeat using the 7" telescopic sleeve.

W415-0210 / E / 06.25.03

BGD36PTR, BGD36NTR, GD36PTR, GD36NTR specifications

Napoleon Fireplaces is a brand renowned for its commitment to quality, innovation, and style in home heating solutions. Among their exceptional offerings are the GD36NTR, GD36PTR, BGD36NTR, and BGD36PTR models, which epitomize modern gas fireplace design with an array of features, technologies, and characteristics.

The GD36NTR (Natural Gas) and GD36PTR (Propane) models are designed to provide warmth and ambiance with elegance. These fireplaces boast a compact yet stylish design that fits seamlessly into any living space. The impressive heat output ranges up to 30,000 BTUs, ensuring a cozy environment even in the coldest months. The included large glass viewing area enhances the aesthetics of the fireplace, allowing for an unobstructed view of the mesmerizing flames.

Equipped with Napoleon’s advanced heat radiating system, the GD36 series enhances warmth distribution, making it efficient and effective. The innovative electronic ignition ensures that lighting the fireplace is easy and reliable, offering both convenience and safety.

In contrast, the BGD36 series, consisting of BGD36NTR and BGD36PTR, brings a different approach with its built-in design suited for new constructions and renovations. These models emphasize versatility and adaptability, fitting into a variety of settings. The BGD36 models similarly deliver aesthetic appeal with their expansive glass front, and they feature a powerful heat output of up to 30,000 BTUs.

Both the GD36 and BGD36 series integrate Napoleon’s patented PHAZER® Log Set that mimics the look of real wood logs, ensuring a lifelike flame experience. The adjustable flame height feature allows users to customize the ambiance according to their moods, ranging from a gentle glow to full, roaring flames.

Another remarkable feature is the multi-function remote control that provides fingertip access to all fireplace functions, enhancing user experience. Complementing these features is the inclusion of a safety screen, which ensures that families can enjoy their fires with peace of mind.

Both series highlight energy efficiency, complying with strict environmental regulations while providing the coziness expected from a traditional fireplace. With their stylish designs, innovative technologies, and commitment to safety and efficiency, the Napoleon Fireplaces GD36NTR, GD36PTR, BGD36NTR, and BGD36PTR make the perfect addition to any home, blending warmth and modern sophistication.