Vertical Venting Installation

1.Move the fireplace into position.

2.Fasten the roof support to the roof using the screws provided. FIGURE 21. The roof support is optional. In this case the venting is to be adequately supported using ei- ther an alternate method suitable to the authority having jurisdiction or the optional roof support.

3.Apply high temperature sealant to the outer edge of the inner sleeve of the air terminal. Slip a 5" diameter coupler a minimum of 2" over the sleeve and secure using 3 screws.

RESTRICTING VERTICAL VENTS

FIGURE 29

TOP OF THE

FIREBOX

FLUE COLLAR

RESTRICTOR PLATE

4. Apply high temperature seal- ant to the outer edge of the of the outside sleeve of the air terminal. Slip a 8" diameter coupler over the sleeve and secure as before. FIG- URE 25. Trim the 8" coupler even with the 5" coupler end.

5. Thread the air terminal pipe assembly down through the roof support and attach, ensuring that a minimum 16" of air terminal will penetrate the roof when fas- tened. FIGURE 23. If the attic space is tight, we recommend threading the Wolf Steel vent pipe collar or equivalent loosely onto the air terminal assembly as it is passed through the attic. FIGURE 29. The air terminal must be located vertically and plumb.

FIGURE 28

VENT

PIPE

COLLAR

VENT PIPE SHIELD

FIGURE 29

Vertical terminations may display a very active flame. As this appearance is not desirable, the vent exit must be restricted using restrictor plate, W500-0205. This reduces the velocity of the exhaust gases, slowing down the flame pattern and creating a more traditional appearance.

Remove the two screws on either side of the exhaust collar inside the firebox. Install the plate as shown. Replace the screws.

GAS INSTALLATION

6.Remove nails from the shingles, above and to the sides of the chimney. Place the flashing over the air termi- nal and slide it underneath the sides and upper edge of the shingles. Ensure that the air terminal is properly centered within the flashing, giving a 3/4" margin all around. Fasten to the roof. Do NOT nail through the lower portion of the flashing. Make weather-tight by sealing with caulking. Where possible, cover the sides and top edges of the flash- ing with roofing material. FIGURE 23.

7.Apply a heavy bead of waterproof caulking 2 inches above the flashing. Slide the storm collar around the air terminal and down to the caulking. Tighten to ensure that a weather-tight seal between the air terminal and the collar is achieved. Attach the other storm collar centered between the air intake and air exhaust slots onto the air terminal. Tighten securely. Attach the rain cap.

8.Continue adding rigid venting sections, sealing and securing as above. Attach a 5" collapsed telescopic pipe to the last section of rigid piping. Secure with screws and seal. Repeat using a 8" telescopic pipe.

9.Run a bead of high temperature sealant around the outside of the 5" collar on the fireplace. Pull the adjustable pipe a minimum of 2" onto the collar. Secure with 3 screws. Repeat with the 8" telescopic pipe.

10.In the attic, slide the vent pipe collar down to cover up the open end of the shield and tighten. This will prevent any materials, such as insulation, from filling up the 1" air space around the pipe.

Proceed once the vent installation is complete.

1.Move the fireplace into position and secure using the nailing tabs and/or secure to the floor through the ¼"diam- eter holes located at either end of the base.

2.Route a 3/8" N.P.T. black iron gas line, 1/2" type-L cop- per tubing or equivalent to the fireplace.

3.For ease of accessibility, an optional remote wall switch or millivolt thermostat may be installed in a convenient lo- cation. Route 2-strand (solid core) millivolt wire through the electrical hole located at the bottom left side of the unit. The recommended maximum lead length depends on wire

size:	WIRE SIZE		MAX. LENGTH
	14	gauge	100 feet
	16	gauge	60 feet
	18	gauge	40 feet

Attach the two leads to terminals 1 and 3 located on the gas valve.

	1
	2		OL		O
FIGURE 30				N	F
			HI	O	F
			HI		IP
					IP
		3			TOL
		3	IP
			TOL

4.Install rigid black pipe, 1/2" type-L copper tubing or, if local codes permit, a 3/8" flex connector and shutoff valve

to the gas line and the fireplace gas valve.

W415-0381 / C / 05.13.04	FIGURE 31

BGDV42P, BGDV42N specifications

Napoleon Fireplaces has long been synonymous with quality and innovation in the heating and home comfort space. Among their impressive lineup, the BGDV42N and BGDV42P gas fireplaces stand out as exceptional options that combine aesthetic appeal with advanced technology. Designed to meet various needs, these models enhance any living space while providing efficient warmth.

The BGDV42N and BGDV42P feature a large, realistic flame pattern that creates a comforting ambiance. With a viewing area that significantly improves the overall visual impact, users can enjoy a spectacular fire display, making these models perfect for both modern and traditional homes. The glass front design ensures optimal heat retention and efficiency, allowing homeowners to relish in both style and functionality.

Both models operate with unrivaled efficiency, employing innovative technologies such as the advanced variable speed blower. This feature enhances heat distribution throughout the room, ensuring that warmth reaches every corner. Furthermore, their electronic ignition with battery backup ensures dependable performance even during power outages, making them practical choices for any season.

The BGDV42N and BGDV42P come equipped with Napoleon's patented NIGHT LIGHT technology, providing ambient illumination even when the fireplace is turned off. This feature adds versatility, allowing homeowners to create a welcoming atmosphere at any time. The fireplaces also include a choice of decorative media options such as modern crystals or traditional logs, enabling users to customize the appearance to match their personal style.

Safety and ease of use are paramount, and both models offer a range of convenient controls. The remote control allows homeowners to adjust the flame height and temperature with ease, while the built-in safety features, including a glass front that remains cool to the touch, ensure peace of mind during use.

With their combination of beautiful design, advanced technology, and reliable performance, the Napoleon BGDV42N and BGDV42P gas fireplaces represent the pinnacle of modern heating solutions. Whether you seek to upgrade an existing space or create an inviting new focal point, these models provide an ideal solution for comfort and style. Embrace the warmth and elegance that Napoleon Fireplaces offers and transform your living area into a cozy retreat.