Restricting Vertical Vents, Framing | Napoleon Fireplaces BGD90NT

FIGURE 24

FIGURE 22

GAS INSTALLATION

Proceed once the vent installation is complete.

NOTE: All gas connections must be contained within the fireplace when complete.

1.Move the fireplace into position and secure to the floor through the 1/4" holes located at either side of the base.

2.The fireplace is designed to accept 3/8" gas supply line. The fireplace is equipped with a 3/8" manual shut-off valve.

3.Connect the gas supply in accordance to local codes. In the absence thereof, install according to the National Installation Code.

4.When flexing any gas line, support the gas valve so that the lines are not bent or kinked.

5.Check for gas leaks by brushing on a soap and water solution.

Do not use open flame.

Purge all gas lines with the glass door of the fireplace removed. Assure that a continuous gas flow is at the burners before re-installing the door.

MOBILE HOME

This appliance is certified to be installed as an OEM (Original Equipment Manufacturer) installation in a manufactured home or mobile home and must be installed in accordance with the manufacturer’s instructions and the Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280, in the United States or the Mobile Home Standard, CAN/CSA Z240 MH Series, in Canada. This appliance is only for use with the type(s) of gas indicated on the rating plate. A conversion kit is supplied with the mobile home appliance.

This Mobile/Manufactured Home Listed appliance comes factory equipped with a means to secure the unit. The fireplace is equipped with two 1/4" diameter holes located in the front left and right corners of the base. For mobile home installations, the fireplace must be fastened in place. Use #10 hex head screws, inserted through the holes in the base to secure. Always turn off the pilot and the fuel supply at the source, prior to moving the mobile home. After moving the mobile home and prior to lighting the fireplace, ensure that the logs are positioned correctly.

This appliance is certified to be installed in an aftermarket permanently located, manufactured (mobile) home, where not prohibited by local codes. This fireplace is only for use with the type of gas indicated on the rating plate. This fireplace is not convertible for use with other gases, unless a certified kit is used.

Conversion Kits

The mobile home appliance is field convertible between Natural Gas (NG) and Propane (LP).

To convert from one gas to another consult your Authorized dealer/distributor.

RESTRICTING VERTICAL VENTS

FLUE COLLAR

RESTRICTOR

PLATE

FIGURE 23

Vertical terminations may display a very active ﬂ ame. If this appearance is not desirable, the vent exit must be restricted using restrictor plate, W500-0321. This reduces the velocity of the exhaust gases, slowing down the ﬂ ame pattern and creating a more traditional appearance.

The plate has a series of holes to allow for adjustment.

Remove the two screws on either side of the exhaust collar inside the ﬁ rebox. Install the plate in the desired set of holes, then replace the screws.

It is recommended to secure in the third set of holes which causes the greatest amount of restriction for vent lengths between 15 and 30 feet.

FRAMING

WARNING

THE STANDOFFS HAVE BEEN SHIPPED FLAT.

BEFORE FRAMING

ENSURE THE STANDOFFS

ARE BENT UP AND

SCREWED INTO PLACE.

ATTENTION	ATENCIÓN
LES ESPACEURS SONT	LAS TRABAS PERMANECEN
EMBALLÉS À PLAT. AVANT DE	PLANAS DURANTE EL ENVÍO.
CONSTRUIRE L'OSSATURE,	ANTES DE LA INSTALACIÓN,
ASSUREZ-VOUS QUE LES	VERIFIQUE QUE LAS TRABAS
ESPACEURS SONT PLIÉS	SE PLIEGUEN HACIA ARRIBA
ET FIXÉS EN PLACE À	Y SE ATORNILLEN
L'AIDE DE VIS.	CORRECTAMENTE.

The can be installed with a rectangular opening.

It is best to frame your ﬁ replace after it is positioned and the vent system is installed. Use 2x4’s and frame to local building codes.

NOTE: In order to avoid the possibility of exposed insulation or vapor barrier coming in contact with the ﬁ replace body, it is recommended that the walls of the ﬁ replace enclosure be “ﬁ nished” (i.e.: drywall/sheetrock), as you would ﬁ nish any other outside wall of a home. This will ensure that clearance to combustibles is maintained within the cavity.

For convenience, the stand-offs have been shipped ﬂat. Before framing, ensure the stand- offs are opened and screwed in place.

It is not necessary to install a hearth extension, but the ﬁ replace should be raised to be ﬂ ush with either the hearth or the ﬁ nished ﬂ oor.

When roughing in the ﬁ replace, raise the ﬁ replace to accommodate for the thickness of the ﬁ nished ﬂ oor materials, i.e. tile, carpeting, hard wood, which if not planned for will interfere with the removal of the hearth strip, which must be removed to access the ﬁ rebox. Objects placed in front of the ﬁ replace should be kept a minimum of 48” away from the front face.

W415-0580 / C / 04.07.08

BGD90PT, BGD90NT specifications

The Napoleon Fireplaces BGD90PT and BGD90NT represent the pinnacle of modern fireplace design, combining cutting-edge technology with timeless aesthetics. These models are specifically crafted for those who value both warmth and style in their living spaces.

One of the standout features of the BGD90PT and BGD90NT is their large viewing area, which allows an unobstructed view of the flames, creating a mesmerizing focal point in any room. The expansive glass front enhances the ambiance of the fire, making it feel more immersive and inviting. This sleek design not only provides aesthetic benefits but also improves heat distribution, contributing to the overall efficiency of the fireplace.

The BGD90PT (Propane) and BGD90NT (Natural Gas) models utilize a range of advanced technologies to enhance performance. The patented PHAZER® technology creates a beautiful and realistic flame effect, while the variable speed blower and adjustable heat output allow for customized comfort levels. This precise control ensures that users can maintain the perfect temperature, regardless of outside conditions.

Furthermore, these models are engineered with Napoleon's exclusive TOP-VENT technology, which provides flexible venting options for easy installation. This feature allows homeowners to maximize their living space and choose the venting configuration that best suits their home’s layout.

The BGD90PT and BGD90NT also prioritize safety and efficiency. Both models are equipped with an electronic ignition system that provides reliable start-up, eliminating the hassle of traditional pilot lights. Additionally, the fireplaces include a built-in safety barrier to prevent accidental contact with the glass, making them suitable for homes with children and pets.

With their impressive heat output, the BGD90PT and BGD90NT can efficiently warm larger spaces, contributing to the overall comfort of your home. Their Energy Star rating ensures that they meet the highest standards for energy efficiency, making them an eco-friendly choice.

In terms of design, both models feature a contemporary look that complements various interior styles. From rustic to modern aesthetics, the BGD90PT and BGD90NT can enhance any home décor while providing the warmth and ambiance of a traditional fireplace.

In conclusion, the Napoleon Fireplaces BGD90PT and BGD90NT are an exceptional fusion of design, technology, and efficiency. Their impressive features make them an ideal choice for anyone looking to add a touch of elegance and functionality to their space, all while enjoying the comforting warmth of a beautiful fire.