Vermont Casting 3358, RUVSOD: 3357, thru 3379, 3370 manual Attach the fan assembly to the fan bracket

Page 11

4.Attach the fan assembly to the fan bracket provided in the log box. Use #10 sheet metal screws provided with fan kit. Do not remove finger guard screws.(Fig. 10)

Snapstat

Wire

Rheostat

Wire

Fan

Bracket

Finger Guard

ST669

Fig. 10 Attach the fan assembly to the fan bracket.

5.Connect snapstat leads. Disconnect the snapstat module from the leads inside the snapstat bracket. (Fig. 11) Bend open the snapstat bracket. Use needlenose pliers to remove the black plastic grommet from the bracket. Discard the bracket. Insert the grommet and wires into the large hole at the bottom right corner of the inner shroud. Feed the snapstat wire leads through the grommet into the stove interior. Connect the two wires to the two snapstat extension leads attached to the inner shroud.

Snapstat Bracket

Snapstat Module

Pinch

Grommet to

Remove

ST670

Fig. 11 Remove the snapstat and grommet from the bracket and insert the grommet into the inner shroud.

Radiance Vent-Free Gas Heater

6.Position the fan assembly so the ducts slide be- tween the inner and outer shroud. The inner shroud should engage with the two slots in the ends of the bracket so that bracket and shroud are interlocked.

(Fig. 12) Secure the bracket with the four sheet metal screws provided in the finish bag.

7.Route the rheostat wire assembly to the right be- tween the inner and outer shroud. Run the wire through the slots at the bottom right corner of the inner shroud.

8.Refasten the outer shroud to the inner duct assem- bly.

Outer

Slot

Shroud

 

 

{Inner Shroud}

 

Slot

 

ST194

Fig. 12 Position the fan to engage the inner shroud with the fan bracket slots and secure with sheet metal screws.

9.Install the snapstat by loosening the front screw on the inner side of the duct (Fig. 13) slide the snapstat under the head of the screw and tighten. Connect the leads to the snapstat. Make sure the snapstat assembly is mounted straight front to back.

Left Air Duct

Snapstat

 

ST671

Fig. 13 Install the snapstat and connect the extension wire terminals. View is with top removed, however, access is available through the rear when installing fan before gas line connection.

10.Slide shroud assembly over the sides and fasten the four screws loosened earlier.

11.Plug the power cord into a standard grounded 110 volt household outlet. If the fan control knob is not turned to the OFF position, the fan will turn on when the temperature at the snapstat reaches approximately 109°F.

20004555

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Radiance Table Of Contents Carbon Monoxide Poisoning MAY Lead to Death Installation & Operating InstructionsRadiance Vent Free dimensions Radiance Vent Free Gas Heater DimensionsMantel from Do not install this heater in a bathroom or bed- roomMinimum Clearances to Combustible Materials Hearth RequirementsOdor During Operation Gas SpecificationsGas Inlet and Manifold Pressures High ElevationsUnusually Tight Construction Vent Free FeaturesFresh Air Requirements for Combustion Ventilation Provide For Adequate VentilationR N I N G Unpacking the Radiance Assembly ProceduresHardware Bag Contents Tools RequiredAssemble the Legs Install Optional FanKit Contents Attach the fan assembly to the fan bracket Thermostat Connection Optional Install ON/OFF SwitchBe sure injector orifices remain at 90 to the base Glass & Catalyst InstallationAged Logs Install Log SetConnect the Gas Supply Line Install the left and right rear logs and the right log Complete the InstallationYour First Fire Flame CharacteristicsFlame & Temperature Adjustment OperationWhat to do if YOU Smell GAS To Turn Off Gas To HeaterIgnitor Electrode sparks, but Pilot does not light TroubleshootingNo spark at pilot when Ignitor is operated flame goes out while in operation Pilot lights but Main Burner does notMain Burner shuts off and Pilot Glass Replacement MaintenanceFirebox Cleaning and Inspection Cleaning ProcedureReplace the Combustor Module Clean the Combustor ModuleCatalytic Combustor Remove the Combustor ModuleRuvsod DescriptionShell Enamel Part Numbers Radiance Vent Free Gas Heater Radiance Vent Free Gas Heater RuvsodOptional Accessories Radiance Vent-Free Gas Heater Radiance Vent-Free Gas Heater If Warranty Service is NEEDED… Limited Lifetime WarrantyCFM Specialty Home Products

3358, RUVSOD: 3357, 3370, thru 3379 specifications

Vermont Casting's RUVSOD series, comprising models 3357, 3358, 3370, and 3379, is widely recognized for its exceptional performance and timeless design. These wood stoves are crafted from durable cast iron, ensuring longevity and optimal heat retention. Each model in the RUVSOD line showcases Vermont Casting's commitment to quality, efficiency, and aesthetic appeal.

One of the key features of the RUVSOD series is its remarkable efficiency. With an EPA-certified efficiency rating, these stoves are designed to maximize heat output while minimizing emissions. Users can enjoy a clean-burning fire that not only warms their space but also meets environmental standards. This efficiency is complemented by advanced technologies such as secondary combustion and catalytic converters, which enhance combustion processes and further reduce smoke and particulate emissions.

The RUVSOD models also come equipped with Vermont Casting's unique AirWash system. This innovative feature helps keep the glass door clean, allowing users to enjoy an unobstructed view of the flames. Additionally, the stoves in this series feature a customizable design, allowing consumers to choose from an array of colors and finishes that suit their interior decor. The stylish look of each stove adds a touch of elegance to any living space.

Another standout characteristic of the RUVSOD models is their user-friendly controls. An easy-to-use draft control system makes it simple to adjust the heat output and burn rate according to individual preferences. This ensures that users can maintain a comfortable and cozy atmosphere in their homes throughout the colder months.

In terms of heating capacity, these models can efficiently warm homes of various sizes, which makes them versatile for both small and large spaces. Their high heat output combined with long burn times ensures that users can enjoy hours of continuous heat without the need for frequent refueling.

In summary, the Vermont Casting RUVSOD series—models 3357, 3358, 3370, and 3379—represents the perfect blend of performance, style, and efficiency. With features such as advanced combustion technology, a customizable aesthetic, user-friendly controls, and impressive heating capabilities, these wood stoves stand as a premier choice for those looking to enhance their living space with an effective and attractive heating solution.
Top Page Image Contents