Single Venting, Fuel, Creosote, Backpufﬁng

Dutchwest Non-Catalytic Convection Heater

for installing a different appliance without relocating the thimble.

There should be no more than eight feet of single-wall stove pipe between the stove and a chimney. Longer runs can cool the smoke enough to cause draft and creosote problems. Use double-wall stove pipe for longer runs.

Single Venting

Your stove requires a dedicated ﬂue. Do not connect the stove to a ﬂue used by any other appliance. Chim- ney draft is a natural form of energy and follows the path of least resistance. If the stove is vented to a ﬂue that also serves an open ﬁreplace or another appliance, the draft will also pull air in through those avenues.

The additional air ﬂow will lower ﬂue temperatures, reduce draft strength and promote creosote develop- ment; overall stove performance will suffer. The effect is similar to that of a vacuum cleaner with a hole in the hose. In some extreme instances, the other appliance can even impose a negative draft and result in a dan- gerous draft reversal.

Fuel

Even the best stove installation will not perform well with poor fuel. If available, always use hardwood that has been air-dried (“seasoned”) 12-18 months. Soft- wood burns more rapidly than hardwood and has a high pitch content that can result in creosote. Decayed wood of any type has little heat value and should not be used.

Unseasoned (‘green’) wood has a high moisture con- tent. Much of its heat value will be used to evaporate moisture before the wood can burn. This signiﬁcantly reduces the amount of energy available to warm your home, as well as the intensity of the ﬁre and tempera- ture of the exhaust gas. Incomplete combustion and cool ﬂue temperatures promote creosote formation and weak draft.

You can judge the moisture content of wood by its ap- pearance and weight or use a commercially available moisture meter for an exact measurement. Unsea- soned wood will be a third heavier than dry wood. Also, look for cracks (“checking”) in the ends of the log that result from contraction as the wood dries. The longer and wider the cracks are, the dryer the wood is.

Creosote

Creosote is a by-product of low-temperature stove operation, weak draft, or both. It is a tar that results when unburned gases condense inside the ﬂue sys- tem at temperatures below 290˚ F. Creosote is volatile and can generate a chimney ﬁre. All of the installation characteristics that adversely affect chimney draft also promote creosote condensation. Consequently, you can

minimize creosote accumulation with an effective chim- ney design and the use of operational techniques that encourage good draft and complete combustion.

Inspect your chimney frequently and clean it whenever accumulation exceeds 1/4”.

Backpufﬁng

Backpufﬁng is a condition that results when the draft is too weak to pull ﬂue gases out of the chimney system as fast as the ﬁre generates them. Volatile gases build up within the ﬁrebox until reaching a density and tem- perature at which they ignite. With this ignition, you may hear a mufﬂed popping sound and see a bit of smoke forced out of the stove.

This condition is most likely to occur in the Spring or Fall when moderate outdoor temperatures and low intensity ﬁres produce weak draft. If your stove back- puffs, open the damper to let the smoke rise to the ﬂue more quickly. Also, open the air inlets to induce a livelier ﬁre and speed airﬂow through the stove. Avoid large loads of ﬁrewood at one time. You should always see lively, dancing ﬂames in the ﬁrebox; a lazy, smoky ﬁre is inefﬁcient and will promote draft problems.

Draft Testing

An easy way to determine whether your chimney draft is strong enough is to close the stove damper, wait a few minutes to let the airﬂow stabilize, and then test whether you can vary the strength of the ﬁre by swing- ing the air control open and closed. Results here are not instant; you may need to wait a few minutes for a change in the air control setting to have an effect on the ﬁre. If there is no change, the draft is not yet strong enough to let you close the damper. You will need to open it for a while longer and manage the ﬁre with the air inlet until the draft strengthens.

Keep a record of your operating habits and relate them to their effects on the stove’s function. You’ll be reward- ed with safe and efﬁcient performance.

Negative Pressure

Good draft also depends on a sufﬁcient supply of air to the stove. The chimney can’t pull in more air than is available to it. Sluggish draft can be caused by a house that is tight enough to prevent the ready ﬂow of air to the stove, or by competition between the stove and other appliances that vent indoor air to the outside; i.e., exhaust fans for range hoods, clothes dryers, bathroom fans, etc.

If the chimney draws well when all such equipment is turned off (or sealed, in the case of ﬁreplaces and/or other stoves), you need to be attentive in timing the use of the other appliances. If you need to crack a nearby

30002291