Vermont Casting 1655, 1656, 1657, 1658, 1659 Connection Above the Fireplace, Wall Pass-throughs

Page 7

Connection Above the Fireplace

In this installation, the chimney connector enters the fireplace flue through a thimble located above the fireplace. (Fig. 6) The liner of the fireplace chimney should extend at least to the point at which the chim- ney connector enters the chimney. Follow all the guidelines for installing a chimney connector into a freestanding masonry chimney, and pay special attention to these additional points:

•The stove and chimney connector clearances to combustible mantel and trim materials are the same as clearances to combustible walls. If necessary, use a combination of mantel, trim, and connector heat shields to provide the required clearances. Refer to page 12.

•Double-check connector clearance to the ceiling.

•The fireplace damper must be closed and sealed to prevent room air from being drawn up the flue which could reduce performance. However, it must be possible to reopen the damper to inspect or clean the chimney.

•Floor protection requirements also apply to fireplace installations.

Wall Pass-throughs

Vermont Castings Madison

Chimney Connector

Heat Shield

*

 

Note clearance

 

*requirement on

*

pages 12-13

 

 

Mantel

ST244a

Fig. 6 If the clearance between the chimney connector and either the ceiling or the mantel is inadequate, a protective heat shield is required.

Whenever possible, design the installation so that the connector does not pass through a combustible wall. If you must include a wall pass-through in your installa- tion, check with your building inspector before you begin. Also check with the chimney connector manu- facturer for any specific requirements.

Consult with your dealer regarding special connec- tion components available for use as wall pass- throughs. Use only parts that have been tested and listed for use as a wall pass-through.

U.S. Requirements:

The National Fire Protection Association (NFPA) has

Fire clay liner

A

A

Min. 2" (51mm) Chimney clearance to brick and combustibles

Masonry

 

Min. 12"

Chimney

Flue

(305 mm)

constructed

 

 

 

to NFPA

Chimney

Chimney

211

 

 

connector

 

 

 

 

Fire clay

 

 

liner

A = Minimum 12" (305 mm) brick construction between liner and combustible framing materials

ST272

established guidelines for use in the United States for passing chimney connectors through combustible walls. Many building code inspectors follow these guidelines.

Fig. 7 Masonry Wall Pass-through with single wall chimney connector.

Figure 7 shows one NFPA-approved method. All combustible material in the wall is cut away to provide 12" (300 mm) clearance to the connector. Brick and mortar are used to enclose the clearance area.

Alternate methods approved by the NFPA:

• Using a section of double-wall chimney with a 9"

(230 mm) clearance to combustibles. (Fig. 8)

Solid insulated, listed factory- built chimney

length set flush

Min. 9"with flue 230mm

Masonry

Chimney constructed to NFPA 211

 

Min. 2"

 

(51mm)

 

Min. 9"

Flue

(230mm)

Chimney

Chimney

Connector

Air Space

 

• Placing a chimney connector pipe inside a steel

double-wall ventilated thimble, which is then sepa-

rated from combustibles by 6" (150 mm) of fiber-

glass insulating material. (Fig. 9)

 

 

Non-soluble

24 ga.Sheet

 

Sheet Steel

Steel

 

refractory cement

Supports

 

Supports

ST273

 

 

 

 

 

Fig. 8 Wall Pass-through using factory-built insulated chimney section.

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Madison Introduction Table of ContentsMadison, Model 1655 Series SpecificationsMasonry Chimneys InstallationPrefabricated Chimneys Chimney Connector GuidelinesChimney Size Freestanding Installations Double-wall Chimney ConnectorsSingle-wall Chimney Connectors Securing the Single-wall Connector to a Masonry ChimneyWall Pass-throughs Connection Above the FireplaceRequirements Floor Protection Canadian RequirementsClearance to Surrounding Combustible Materials Fireplace Hearth ProtectionSafe Ways To Reduce Clearances = 1 25 mm Wall ShieldsConstruction Requirements Alcove InstallationsMadison 1655 Series Clearance Chart Madison 1655 Series Clearance Diagram ST563 Assembly With Rear Heat Shield Install the Outside Air AdaptorBurn Only High-Quality Wood Use the Air Control Setting that Works Best for YouOperation How the Madison WorksStarting and Maintaining a Fire Madison Control SettingsRefuel While the Embers Are Still Hot Ash DisposalMaintenance Creosote Clean the Primary Air OutletFlue Sizing Draft ManagementSteel Chimney Inside/Outside LocationNegative Pressure Single VentingFuel BackpuffingMadison Woodburning Stove Madison Woodburning Stove Vermont Castings Madison Warranty Vermont Castings, Majestic Products

1655, 1656, 1657, 1658, 1659 specifications

Vermont Castings has long been synonymous with high-quality cast iron stoves and fireplaces, and models 1655, 1656, 1657, 1658, and 1659 are prime examples of the craftsmanship and innovation that define the brand. Each model showcases a unique combination of features, technologies, and characteristics designed to enhance the home heating experience.

The Vermont Castings 1655, also known as the Defiant wood stove, is revered for its exceptional heating efficiency and classic design. With a large firebox, it can accommodate logs up to 18 inches long, making it an ideal choice for long, uninterrupted burns. Its dual door design not only provides ease of access but also enhances the aesthetic appeal with its elegantly arched glass. The stoves feature the brand's innovative Catalyst technology, which ensures complete combustion of gases, reducing emissions while maximizing heat output.

The 1656 model, known as the Intrepid II, is compact yet powerful. It is perfect for smaller spaces, providing significant heat without compromise. With its traditional styling and hand-crafted quality, it stands as a testament to Vermont Castings' commitment to aesthetics. The stove incorporates a secondary combustion system, which enhances efficiency by reburning flue gases, ensuring a cleaner burning process.

The 1657 model, also recognized as the Vigilant, incorporates radiant and convective heating, which is perfect for larger rooms. This model is equipped with advanced clean-burning technology, facilitating a longer burn time and reducing the frequency of reloads. The stovetop is designed to maintain heat, allowing for cooking or warming food, illustrating its versatility.

In contrast, the 1658 model, known as the Resolute, features an elegant yet rugged design that complements various interiors. Its air-wash system keeps the glass door clean, providing an unobstructed view of the flames. The Resolute is designed for easy operation, with an adjustable damper that tailors airflow, further optimizing efficiency according to user preferences.

Finally, the 1659, or the Encore model, stands out with its revolutionary two-in-one design that allows for top or front loading. This model is known for its exceptional heat retention and long burn times, catering to homeowners who value convenience and performance. Its eco-friendly features include reduced emissions and high-efficiency ratings that meet modern environmental standards.

In summary, Vermont Castings' 1655, 1656, 1657, 1658, and 1659 models offer an array of features that prioritize efficiency, performance, and style. From their unique combustion technologies to their stunning craftsmanship, these stoves represent some of the best options in the market for effective home heating solutions. Each model is a testament to Vermont Castings' enduring legacy of quality and innovation in the world of wood-burning appliances.
Top Page Image Contents