Vermont Casting 1655, 1656, 1657, 1658, 1659 installation instructions Fireplace Hearth Protection

Page 9

To meet these requirements, a floor protector must be at least 54” (1372mm) wide (“A”,Fig. 12) and 52” (1320mm) deep (“B”, Fig. 12).

Fireplace Hearth Protection

Do not assume that your fireplace hearth is completely noncombustible. Many fireplace hearths do not satisfy the “completely noncombustible” requirement because the brick or concrete in front of the fireplace opening is supported by heavy wood framing. (Fig. 13) Because heat is readily conducted by brick or concrete, it can easily pass through to the wood. As a result, such fireplace hearths can be a fire hazard and are consid- ered a combustible floor.

For all fireplace installations, follow the floor protection guidelines described above.

Keep in mind that many raised hearths will extend less than the required clearance from the front of the heater when it is installed. In such cases, sufficient floor protection as described above must be added in front of the hearth to satisfy the minimum floor protec- tor requirement from the front of the stove: 18" (460

mm)from the front in the United States and 18" (460

mm)from the front in Canada.

Hearth rugs do not satisfy the requirements for floor protection as they are only fire-retardant, not fire proof.

Floor Protection Requirements

 

 

 

 

Rear Vent

 

 

 

 

F

 

Top Vent

 

 

 

C

 

 

C

 

 

 

B

 

 

E

C

 

E

C

 

 

D

 

 

D

 

A

 

 

A

 

 

U. S.

Canada

 

A:

48”

54”

(1372mm)

 

B:

48”

52”

(1321mm)

 

C:

4”

8”

(203mm)

 

D:

18”

18”

(460mm)

 

E:

16”

18”

(460mm)

 

F:

10”

10”

(254mm)

ST500a

Fig. 12 These dimensions are minimum requirements only. Use greater dimensions whenever possible.

Vermont Castings Madison

Wood framing

 

requires protection

ST247a

from radiant heat

Fig. 13 Supporting timbers under fireplace hearths are considered to be combustible.

Clearance to Surrounding

Combustible Materials

When the stove is operating, both the stoveplate and the chimney connector radiate heat in all directions. A safe installation requires that adequate clearance be maintained between the stove and nearby combustible materials to ensure that those materials do not overheat.

Clearance is the distance between either your stove or chimney connector, and nearby walls, floors, the ceiling, and any other fixed combustible surface.

Keep furnishings and other combustible materials away from the stove as well. In general, a distance of 48" (1220 mm) must be maintained between the stove and moveable combustible items such as drying clothes, furniture, newspapers, firewood, etc. Keep this area empty of any combustible material.

Safe Ways To Reduce Clearances

The Madison clearance requirements, listed and diagramed on pages 12-13, have been established through testing to UL and ULC standards to meet most installation configurations. These involve four basic variables:

•When neither the chimney connector nor the wall has a heat shield installed.

•When only the chimney connector has a heat shield installed.

•When only the wall has a heat shield mounted on it.

•When a heat shield is installed on both the chimney connector and wall.

In general, the greatest clearance is required when the stove will be positioned with no heat shield near a wall with no heat shield. The least clearance is re- quired when both the stove and the wall have heat shields. Reducing a stove clearance may require installation of a listed heat shield on the chimney connector as well.

Clearances may be reduced only by means approved by the regulatory authority, or in accordance with the clearances listed in this manual.

9

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Madison Introduction Table of ContentsMadison, Model 1655 Series SpecificationsMasonry Chimneys InstallationChimney Connector Guidelines Prefabricated ChimneysChimney Size Single-wall Chimney Connectors Double-wall Chimney ConnectorsSecuring the Single-wall Connector to a Masonry Chimney Freestanding InstallationsConnection Above the Fireplace Wall Pass-throughsRequirements Floor Protection Canadian RequirementsFireplace Hearth Protection Clearance to Surrounding Combustible MaterialsSafe Ways To Reduce Clearances = 1 25 mm Wall ShieldsConstruction Requirements Alcove InstallationsMadison 1655 Series Clearance Chart Madison 1655 Series Clearance Diagram ST563 Assembly With Rear Heat Shield Install the Outside Air AdaptorOperation Use the Air Control Setting that Works Best for YouHow the Madison Works Burn Only High-Quality WoodStarting and Maintaining a Fire Madison Control SettingsRefuel While the Embers Are Still Hot Ash DisposalMaintenance Creosote Clean the Primary Air OutletSteel Chimney Draft ManagementInside/Outside Location Flue SizingFuel Single VentingBackpuffing Negative PressureMadison Woodburning Stove Madison Woodburning Stove Vermont Castings Madison Warranty Vermont Castings, Majestic Products

1655, 1656, 1657, 1658, 1659 specifications

Vermont Castings has long been synonymous with high-quality cast iron stoves and fireplaces, and models 1655, 1656, 1657, 1658, and 1659 are prime examples of the craftsmanship and innovation that define the brand. Each model showcases a unique combination of features, technologies, and characteristics designed to enhance the home heating experience.

The Vermont Castings 1655, also known as the Defiant wood stove, is revered for its exceptional heating efficiency and classic design. With a large firebox, it can accommodate logs up to 18 inches long, making it an ideal choice for long, uninterrupted burns. Its dual door design not only provides ease of access but also enhances the aesthetic appeal with its elegantly arched glass. The stoves feature the brand's innovative Catalyst technology, which ensures complete combustion of gases, reducing emissions while maximizing heat output.

The 1656 model, known as the Intrepid II, is compact yet powerful. It is perfect for smaller spaces, providing significant heat without compromise. With its traditional styling and hand-crafted quality, it stands as a testament to Vermont Castings' commitment to aesthetics. The stove incorporates a secondary combustion system, which enhances efficiency by reburning flue gases, ensuring a cleaner burning process.

The 1657 model, also recognized as the Vigilant, incorporates radiant and convective heating, which is perfect for larger rooms. This model is equipped with advanced clean-burning technology, facilitating a longer burn time and reducing the frequency of reloads. The stovetop is designed to maintain heat, allowing for cooking or warming food, illustrating its versatility.

In contrast, the 1658 model, known as the Resolute, features an elegant yet rugged design that complements various interiors. Its air-wash system keeps the glass door clean, providing an unobstructed view of the flames. The Resolute is designed for easy operation, with an adjustable damper that tailors airflow, further optimizing efficiency according to user preferences.

Finally, the 1659, or the Encore model, stands out with its revolutionary two-in-one design that allows for top or front loading. This model is known for its exceptional heat retention and long burn times, catering to homeowners who value convenience and performance. Its eco-friendly features include reduced emissions and high-efficiency ratings that meet modern environmental standards.

In summary, Vermont Castings' 1655, 1656, 1657, 1658, and 1659 models offer an array of features that prioritize efficiency, performance, and style. From their unique combustion technologies to their stunning craftsmanship, these stoves represent some of the best options in the market for effective home heating solutions. Each model is a testament to Vermont Castings' enduring legacy of quality and innovation in the world of wood-burning appliances.
Top Page Image Contents