Vermont Casting 1655, 1656, 1657, 1658, 1659 Creosote, Clean the Primary Air Outlet

Page 21

The Chimney System

Creosote

Your Madison is designed to reduce creosote buildup significantly. However, regular chimney inspection and maintenance must still be performed. For safety, good stove performance, and to protect your chimney and chimney connector, inspect your chimney and chimney connector on a regular schedule. Clean the system if necessary. Failure to keep the chimney and connector system clean can result in a serious chimney fire.

When wood is burned slowly, it produces tar, organic vapors and moisture that combine to form creosote. The creosote vapors condense in the relatively cool chimney flue. As a result, creosote residue accumulates on the flue lining. When ignited, this creosote makes an extremely hot fire within the flue system that can damage the chim- ney and overheat adjacent combustible material. If you do have a chimney fire, promptly:

•Close the thermostat lever.

•Get everyone out of the house.

•Call the Fire Department.

You should inspect the system every two weeks during the heating season as part of a regular maintenance schedule. To inspect the chimney, let the stove cool completely. Then, using a mirror and a strong light, sight up through the flue collar into the chimney flue. If it is not possible to inspect the flue system in this fashion, the stove must be disconnected to provide better viewing access.

If a significant layer of creosote has accumulated —1/8" (3 mm) or more — remove it to reduce the risk of a chimney fire.

Clean the chimney using a brush the same size and shape as the flue liner. Flexible fiberglass rods are used to run the brush up and down the liner, causing any deposits to fall to the bottom of the chimney where they can be removed through the clean-out door.

The chimney connector should be cleaned by disconnecting the sections, taking them outside, and removing any deposits with a stiff wire brush. Reinstall the connector sections after cleaning, being sure to secure the individual sections with sheet metal screws.

If you cannot inspect or clean the chimney yourself, contact your local Vermont Castings’ Authorized Dealer or hire a professional chimney sweep.

Vermont Castings Madison

Annual Maintenance

Perform a thorough cleaning, inspection and repair each Spring, at the end of the heating season.

•Thoroughly clean the chimney and chimney connec- tor.

•Inspect the chimney for damage and deterioration. Replace weak sections of prefabricated chimney. Have a mason make repairs to a masonry chimney.

•Inspect the chimney connector and replace any damaged sections.

•Clean ash debris from under the primary air plate. See procedure below.

•Check gasketing for wear or compression, and replace if necessary. A 'paper test' will guide you on this. Close and lock the door on a slip of paper and then try to pull the paper out. If the paper pulls out with little or no resistance, the gasket isn't snug enough at that spot. If adjusting the latch doesn't result in a seal that makes it hard to pull the paper out, replace the gasketing.

•Check door handle for tightness. Adjust if needed.

•Check heat shield screws. Tighten as necessary.

•Clean dust from the inner sides of bottom, rear and connector heat shields.

•Remove ashes from the ash pan and replace with moisture absorbing material (such as cat litter) to keep the stove interior dry. Close the stove door to keep cats from using the litter.

•Touch up the paint on black stoves.

Clean the Primary Air Outlet

1.Remove the phillips head screws that retain the Primary Air Plate.

2.Use a screwdriver to pry the plate out of the ce- mented seams.

3.Remove ash debris from the cavity.

4.Use high-temperature furnace cement to reseal the front seam and side seams and replace the plate. Secure with the phillips head screws.

21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents Madison Introduction Table of ContentsMadison, Model 1655 Series SpecificationsMasonry Chimneys InstallationChimney Connector Guidelines Prefabricated ChimneysChimney Size Single-wall Chimney Connectors Double-wall Chimney ConnectorsSecuring the Single-wall Connector to a Masonry Chimney Freestanding InstallationsConnection Above the Fireplace Wall Pass-throughsRequirements Floor Protection Canadian RequirementsFireplace Hearth Protection Clearance to Surrounding Combustible MaterialsSafe Ways To Reduce Clearances = 1 25 mm Wall ShieldsConstruction Requirements Alcove InstallationsMadison 1655 Series Clearance Chart Madison 1655 Series Clearance Diagram ST563 Assembly With Rear Heat Shield Install the Outside Air AdaptorOperation Use the Air Control Setting that Works Best for YouHow the Madison Works Burn Only High-Quality WoodStarting and Maintaining a Fire Madison Control SettingsRefuel While the Embers Are Still Hot Ash DisposalMaintenance Creosote Clean the Primary Air OutletSteel Chimney Draft ManagementInside/Outside Location Flue SizingFuel Single VentingBackpuffing Negative PressureMadison Woodburning Stove Madison Woodburning Stove Vermont Castings Madison Warranty Vermont Castings, Majestic Products

1655, 1656, 1657, 1658, 1659 specifications

Vermont Castings has long been synonymous with high-quality cast iron stoves and fireplaces, and models 1655, 1656, 1657, 1658, and 1659 are prime examples of the craftsmanship and innovation that define the brand. Each model showcases a unique combination of features, technologies, and characteristics designed to enhance the home heating experience.

The Vermont Castings 1655, also known as the Defiant wood stove, is revered for its exceptional heating efficiency and classic design. With a large firebox, it can accommodate logs up to 18 inches long, making it an ideal choice for long, uninterrupted burns. Its dual door design not only provides ease of access but also enhances the aesthetic appeal with its elegantly arched glass. The stoves feature the brand's innovative Catalyst technology, which ensures complete combustion of gases, reducing emissions while maximizing heat output.

The 1656 model, known as the Intrepid II, is compact yet powerful. It is perfect for smaller spaces, providing significant heat without compromise. With its traditional styling and hand-crafted quality, it stands as a testament to Vermont Castings' commitment to aesthetics. The stove incorporates a secondary combustion system, which enhances efficiency by reburning flue gases, ensuring a cleaner burning process.

The 1657 model, also recognized as the Vigilant, incorporates radiant and convective heating, which is perfect for larger rooms. This model is equipped with advanced clean-burning technology, facilitating a longer burn time and reducing the frequency of reloads. The stovetop is designed to maintain heat, allowing for cooking or warming food, illustrating its versatility.

In contrast, the 1658 model, known as the Resolute, features an elegant yet rugged design that complements various interiors. Its air-wash system keeps the glass door clean, providing an unobstructed view of the flames. The Resolute is designed for easy operation, with an adjustable damper that tailors airflow, further optimizing efficiency according to user preferences.

Finally, the 1659, or the Encore model, stands out with its revolutionary two-in-one design that allows for top or front loading. This model is known for its exceptional heat retention and long burn times, catering to homeowners who value convenience and performance. Its eco-friendly features include reduced emissions and high-efficiency ratings that meet modern environmental standards.

In summary, Vermont Castings' 1655, 1656, 1657, 1658, and 1659 models offer an array of features that prioritize efficiency, performance, and style. From their unique combustion technologies to their stunning craftsmanship, these stoves represent some of the best options in the market for effective home heating solutions. Each model is a testament to Vermont Castings' enduring legacy of quality and innovation in the world of wood-burning appliances.
Top Page Image Contents