Vermont Casting 1990CE installation instructions Assembly

Page 11

Intrepid II Woodburning Stove

Assembly

Clean the Griddle Before Use

At the factory the griddle is coated with vegetable oil to prevent rusting while the stove is in transit and storage. Remove the oil with a dry rag or paper towel before you use the stove.

Set Up the Stove

Remove any loose parts from inside the stove. Place a protective pad on the floor, arrange some sections of 4 x 4 lumber on the pad for support, and carefully tip the stove onto them, on its back.

Remove and discard the four large slot-head screws from the stove bottom (Fig. 13) and install the stove legs, using the hex head bolts from the parts bag. Use 3/8” washers with three of the legs; the door/damper handle holder installs in place of a washer on the right front leg. Position the holder so the hole to accept the handle nub faces out from the right side of the stove. Tighten the bolts firmly.

Slotted

 

Screws

 

ST513

Fig. 13

Remove the slotted screws from the stove bottom.

Install the Bottom Heat Shield

A bottom heat shield must be used unless the stove is to be situated on a completely noncombustible hearth, such as unpainted concrete over earth. To install the bottom heat shield, loosen the leg bolts, and slip the bottom heat shield C-clips onto the bolts. Attach the bottom heat shield to the C-clips with the wing nuts, and tighten the leg bolts. Align the shield as shown in Figure 14.

10³⁄₄"

9³⁄₄"

ST512

Fig. 14 Attach bottom heat shield.

Storing the Handle

Use the removable handle to open or close the front doors, or to change the position of the damper. After using it, remove it so it won’t get hot, and store it in the handle holder installed behind the right front leg. (Fig. 15)

Door Handle Holder

Bottom Heat Shield

Bracket

Wing Bolt

ST514

Fig. 15 Handle holder and heat shield positions.

Reversing the Flue Collar

You can reverse the flue collar by removing the two screws that attach the collar to the back of the stove. (Fig. 16) Be sure the gasket around the flue collar opening is in position when you screw the collar back on to the stove.

30003840

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Intrepid Welcome Table of ContentsIntrepid II, Model 1990CE SpecificationsWhat Kind of Chimney to Use InstallationOutside Air Chimney Size Chimney Connector GuidelinesMasonry Chimneys Prefabricated ChimneysFreestanding Chimney Installations Double-wall Chimney ConnectorSingle-wall Chimney Connector Securing the Single-wall Connector to a Masonry ChimneyFireplace Chimney Installations Through a Fireplace Fireplace Chimney Installations Above a FireplaceHearths Wall Pass-ThroughsClearances Floor Protection for Fireplace InstallationsKeep the Stove a Safe Distance from Surrounding Materials Summary of Clearances Assembly Your Intrepid II’s Controls What They Do OperationAttach the Griddle Handle Two Ways to Add Fuel Damper Directs Air Flow Within the StoveGlass Door Panels AndironsSurface Thermometer is a Valuable Guide to Operation Burn Only High-Quality WoodHigh-Efficiency Wood Burning With Catalytic Combustion Use the Air Control Settings that Work Best for YouHow to Build a Wood Fire Keep it Going Starting and Maintaining a Wood Fire Conditioning Your StoveAsh Disposal Refuel While the Embers are Still HotDraft Management Back-puffing Draft TestingCreosote FuelMaintenance Tighten the Damper Handle as Needed How to Adjust the Door LatchDamper Adjustment When to Suspect a Combustion System Problem Catalytic Combustion System Inspection and CleaningReplace the Stove Gaskets as Needed Replace Refractory PackageChimney System Creosote Adjust the Door if NecessaryAnnual Maintenance Permanent GasketsIntrepid II Woodburning Stove Appendix Catalytic Combustor Intrepid II Woodburning Stove Intrepid II Woodburning Stove Please record the following information For future reference Intrepid II Woodburning Stove Warranty CFM Corporation

1990CE specifications

The Vermont Casting 1990CE is a remarkable wood-burning stove that has earned a solid reputation for its innovative design, efficiency, and durability. Renowned for its classic aesthetics and modern functionality, the 1990CE combines traditional craftsmanship with cutting-edge technology, making it a favorite among homeowners looking to enhance their living spaces with both warmth and style.

One of the most notable features of the 1990CE is its exceptional efficiency. The stove is designed to produce a high heat output while minimizing the consumption of wood. With an impressive efficiency rating, it effectively uses the fuel, ensuring that users enjoy longer burn times and reduced firewood usage. This efficiency not only provides warmth but also aligns with eco-friendly practices, reducing the impact on the environment.

The Vermont Casting 1990CE incorporates advanced secondary combustion technology, which allows for a cleaner burn and significantly lowers emissions. This state-of-the-art system ensures that the stove generates less smoke and reduces the amount of pollutants released into the atmosphere. As a result, users can enjoy the benefits of a cozy fire without the guilt of environmental harm.

In addition to its environmental features, the stove is built with a heavy cast iron construction, which ensures durability and longevity. The cast iron design not only provides excellent heat retention but also adds a timeless aesthetic to any home. The 1990CE is available in various finishes, allowing homeowners to select a style that complements their decor.

Another key characteristic of the Vermont Casting 1990CE is its user-friendly design. The stove features an easy-to-use air control system that allows users to adjust the intensity of the fire with ease. This precise control enables the creation of the desired ambiance, whether for a cozy evening or a more intense heating requirement.

Furthermore, the 1990CE offers a large viewing window, framed by a stylish cast iron design, allowing users to enjoy the mesmerizing flames while enhancing the overall visual appeal of the room. The stove’s clean lines and classic design make it a versatile addition to various interior styles, from rustic to contemporary.

Ultimately, the Vermont Casting 1990CE stands out for its combination of efficiency, aesthetic appeal, and user-friendly features. With its commitment to sustainable burning practices and craftsmanship, it provides an ideal solution for those seeking both warmth and style in their homes. Whether for practical heating or the simple joy of a crackling fire, the 1990CE is a remarkable choice that will serve homeowners well for years to come.
Top Page Image Contents