Vermont Casting 1637, 1635 Assembly, Unpack the Stove, Optional Fan Kit, Install the Snapstat

Page 14

Vermont Castings Seville

Assembly

You will need the following tools to assemble the Seville:

• 7/16" open end wrench

• safety glasses & gloves

• flat head screwdriver

• power drill w/ 1/8" (3mm) bit

• stub handle phillips screwdriver

Unpack the Stove

1.Remove the shipping straps and plastic wrap.

2.Inspect the stove and contents for shipping damage or missing parts. Immediately notify your dealer of any damage. Do not install this stove if any damage is evident or any parts are missing.

Hardware Bag contents:

•Stove Legs, 4

•Fan Switch Bracket (for use with optional fan)

•1/4-20 x 1” hex head Leg Bolts with washers, qty 4

•#10 x 1/2" sheet metal screws, qty 2

•Owner's Registration Card

•Touch-up Paint (Porcelain enamel stoves only)

3.Remove the Top Plate from the stove body by lifting up and away. Set it aside for replacement after the stove has been positioned and connected to the chimney.

Optional Fan Kit 2960

Install the Fan Kit within the Rear Shroud before you remove the stove body from the shipping pallet.

To test the fan operation before installation:

1.Connect the power cord to a three prong outlet.

2.Turn the rheostat switch ON.

3.Apply heat to the snapstat. The fan will operate when the snapstat reaches 90˚F.

If the Control is left in the ON position, the fan will shut off when the snapstat temperature falls below 90˚.

Install the Snapstat

1.Disconnect the leads from the Snapstat terminals.

2.Use pliers to remove the retainer ring from the Snapstat Cover and slip the cover off the wire harness. Discard cover.

3.Reconnect the wire leads to the Snapstat Plate.

4.Using two sheet metal screws from the fan kit, attach the Snapstat Plate to the Inner Shroud as indicated in Figure 19.

 

Snapstat

Rear Shroud

 

Leads

 

Snapstat

 

Cover

 

(Discard)

 

ST464

Fig. 19

Install the Snapstat.

ST462

 

Fig. 20

Install the Fan body into the Rear Shroud.

Switch Bracket

Retainer Nut

Control Knob

Switch Box

ST463

Fig. 21-1Install the rheostat switch.

14

30001490

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Seville Introduction Table of ContentsInstallation Accessories Specifications Seville, ModelMasonry Chimneys InstallationChimneys Chimney Size Chimney Connector GuidelinesPrefabricated Chimneys Masonry Chimneys, contdSecuring the Single-wall Connector to a Masonry Chimney Double-wall Chimney ConnectorsSingle-wall Chimney Connectors Freestanding InstallationsAlternate methods approved by the Nfpa Connection Above the FireplaceWall Pass-throughs Wall Pass-through with ventilated steel thimble Floor Protection Fireplace Hearth ProtectionWall Shields Clearance to Surrounding Combustible MaterialsSafe Ways To Reduce Clearances Wall shields Seville 1635 Clearance Chart Stove ClearanceUnprotected Protected Surfaces Alcove InstallationsStove Installed Stove in Corner Parallel to Wall Hardware Bag contents AssemblyInstall the Snapstat Unpack the StoveInstall Stove Legs Install the FanInstall the Rheostat Switch Pedestal AssemblyInstall the Outside Air Adapter Attach the Chimney ConnectorHow the Seville Works Use the Air Control Setting that Works Best for YouOperation Burn Only High-Quality WoodStarting and Maintaining a Fire Conditioning Your Stove Burn Rate Primary Air Control Shutter PositionStart a fire with small, dry kindling Smoke Detectors Refuel While the Embers Are Still HotAsh Disposal Maintenance Adjust the Door CreosoteDraft Management Annual MaintenanceClean the Primary Air Outlet Flue Sizing Steel ChimneyInside/Outside Location Pipe & Chimney LayoutConclusion BackpuffingNegative Pressure Seville Woodburning Stove Seville Vermont Castings, Majestic Products
Top Page Image Contents