Vermont Casting 2550CE installation instructions Through the Fireplace, Wall Pass-Throughs

Page 8

Encore Woodburning Stove

•The fireplace damper must be sealed to prevent room air from escaping up the flue. However, it must be possible to re-open the damper to inspect or clean the chimney.

Chimney

*

Connector Shields

 

 

*

* Check

Mantel

These Clear-

 

ances

 

 

Seal this off

ST244

 

Fig. 7 In this installation, the chimney connector is attached to the chimney above the fireplace opening.

Through the Fireplace

If your fireplace opening height is at least 675 mm (26¹⁄₂"), you may install an Encore through the opening using a “positive connection” kit, available from your local dealer. These positive connection kits ensure a tight fit between the stove flue collar and the chimney flue. (Fig. 8)

Fireplace installations, whether connected to the flue above or through the fireplace opening, have special clearance requirements to adjacent trim and the mantel. You’ll find the required safe clearances for Encore fire- place installations on Page 11.

Floor protection requirements also apply to fireplace installations. This information is on Page 9.

Wall Pass-Throughs

Whenever possible, design your installation so the con- nector does not pass through a combustible wall. If you are considering a wall pass-through in your installation, check with your building inspector before you begin.

Also, check with the chimney connector manufacturer for any specific requirements.

Accessories are available for use as wall pass- throughs. If using one of these, make sure it has been tested and listed for use as a wall pass-through.

Flexible Connector

Mantel Shield

Fireplace Adapter

Kit “Positive Con- nection”

ST245

Fig. 8 In this installation, the chimney connector enters the firepalce opening and then connects to the chimney.

Figure 9 shows one method of passing a connector through a wall. All combustible material in the wall is cut away to provide the required 457 mm (18”) clearance for the connector. The resulting space must remain empty. A flush-mounted sheet metal cover may be used on one side only. If covers must be used on both sides, each cover must be mounted on noncombustible spac- ers at least 25 mm (1”) clear of the wall.

Your local dealer or your local building inspector can provide details for other approved methods of passing a chimney connector through a combustible wall in your area.

DO NOT CONNECT AN ENCORE TO ANY AIR DIS- TRIBUTION DUCT OR SYSTEM.

457 mm (18”) clear space all around the pipe

ST494

Fig. 9 An approved wall pass-through.

8

30003842

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Encore Table of Contents WelcomeSpecifications Encore Model 2550CEChimney Height InstallationOutside Air Chimney Connector Guidelines What Kind of Chimney to UseMasonry Chimneys Prefabricated ChimneysDouble-wall Chimney Connectors Single-wall Chimney ConnectorsSecuring the Single-wall Connector to a Masonry Chimney Freestanding InstallationsFireplace Installations Above the FireplaceThrough the Fireplace Wall Pass-ThroughsKeep the Stove a Safe Distance From Surrounding Materials Floor Protection for Fireplace InstallationsHearths Safe Ways to Reduce Clearances Summary of ClearancesConnecting fluepipe clearances Assembly Operation Encore ControlsSingle Air Control Regulates Heat Output and Burn Time Damper Directs Air Flow Within the StoveTwo Ways to Add Fuel Infrared Reflective Glass Panels For Clear Fire ViewingAndirons Help Protect the Glass Burn Only High-Quality WoodSurface Thermometer is a Valuable Guide to Operation Use the Air Control Settings That Work Best for YouEncore Control Settings Starting and Maintaining a Wood Fire High-Efficiency Wood Burning with Catalytic CombustionConditioning Your Stove Refuel While the Embers Are Still Hot Add larger pieces of wood as the fire begins to burn wellAsh Disposal Draft Management Steel ChimneyIndoor / Outdoor location Flue SizingDraft Testing CreosoteFuel Back-puffingMaintenance Adjust the Damper as Needed How to Adjust the Door LatchesCheck the Operation Primary Air Shutter Tighten the Damper Handle as NeededInspecting the Combustor Catalytic Element Inspection and CleaningWhen to Suspect a Combustor Problem Replace the Stove Gaskets as Needed Gasket Diameter ...And the Parts it SealsChimney System Creosote Adjust the Door If NecessaryPermanent Encore Gaskets Annual Maintenance Appendix Catalytic Combustor Encore Woodburning Stove Encore Woodburning Stove Shell Enamel Parts Encore Color Warranty CFM Corporation

2550CE specifications

The Vermont Casting 2550CE is a remarkable wood-burning stove that embodies both efficiency and style, making it a preferred choice for those who desire a reliable heating solution combined with aesthetic appeal. This model stands out in the realm of traditional wood stoves, offering an exceptional blend of performance features and innovative technologies.

At the heart of the 2550CE is its robust cast iron construction, which contributes to superior heat retention and distribution. Cast iron is known for its ability to radiate warmth long after the fire has dwindled, ensuring a cozy atmosphere in your living space. This model also features a large ceramic glass door, providing a captivating view of the flames while allowing for easy monitoring of the fire's conditions.

One of the defining characteristics of the Vermont Casting 2550CE is its advanced secondary combustion system. This technology enhances the stove's efficiency by reburning the exhaust gases, thus extracting maximum heat from the wood and reducing emissions. This not only makes for a cleaner burn but also extends the burn time, allowing users to enjoy an extended period of warmth with fewer reloads.

The 2550CE is designed with functionality in mind, equipped with an easy-to-use air control system that enables precise regulation of airflow. This allows users to adjust the fire’s intensity based on their immediate heating needs, maximizing both comfort and fuel efficiency. Moreover, the stove’s large firebox accommodates logs up to 18 inches in length, making it practical for those who prefer to minimize the frequency of reloads.

In terms of style, the Vermont Casting 2550CE features a classic design that complements various interior decor styles, including rustic, traditional, and modern settings. Available in several finishes, including matte black and enamel options, the stove can be customized to match individual tastes and home aesthetics.

The commitment to sustainability is another significant aspect of the 2550CE. With its lower emissions rates complying with EPA standards, homeowners can enjoy a warm and inviting environment while being mindful of their environmental impact. Overall, the Vermont Casting 2550CE combines time-tested craftsmanship with modern technology, making it an ideal choice for anyone seeking an efficient and elegant wood-burning stove.
Top Page Image Contents