Vermont Casting 2550CE Double-wall Chimney Connectors, Single-wall Chimney Connectors

Page 6

Encore Woodburning Stove

Flue Pipes with a spigot and socket joint should be fitted with the socket facing upwards, to contain con- densates and moisture within the flue. Joints should be made gas tight using proprietary jointing accessories, or, where appropriate, by packing joint with noncombus- tible rope and fire cement.

Double-wall connectors must be tested and listed for use with solid-fuel burning appliances. Single-wall con- nectors should be made of 24 gauge or heavier steel. Do not use galvanized connector; it cannot withstand the high temperatures that can be reached by smoke and exhaust gases, and may release toxic fumes under high heat. The connector may be 152 mm (6”) or 203 mm (8”) in diameter.

If possible, do not pass the chimney connector through a combustible wall or ceiling. If passage through a com- bustible wall is unavoidable, refer to the section on Wall Pass-Throughs. Do not pass the connector through an attic, a closet or similar concealed space. The whole connector should be exposed and accessible for in- spection and cleaning.

In horizontal runs of chimney connector, maintain a dis- tance of 610 mm (24”) from the ceiling. Keep it as short and direct as possible, with no more than two 90° turns. Slope horizontal runs of connector upward 6 mm per metere (1/4” per foot) going from the stove toward the chimney. The recommended maximum length of a hori- zontal run is 914 mm (36”), and the total length should be no longer than 2.4 m (8’). In cathedral ceiling instal- lations, extend the prefabricated chimney downward to within 2.4 m (8’) of the stove.

Wear gloves and protective eyewear when drilling, cutting or joining sections of chimney connector.

Double-wall Chimney Connectors

Information on assembling and installing double-wall connectors is provided by the manufacturer of the double-wall pipe. Follow the manufacturer’s instructions exactly as you assemble the connector and attach it to the stove and chimney. Using chimneys and connectors from the same manufacturer makes the assembly and installation straightforward.

NOTE: For installations using double-wall connectors, minimum clearances must conform to the listed clear- ances in the clearance chart on Page 14.

If the Encore is equipped with the 203 mm (8”) flue collar, an oval-to-round adapter will be needed. Double- wall oval-to-round adapters are available from some manufacturers. Your local dealer can help you select the right connector.

Single-wall Chimney Connectors

•Begin assembly at the flue collar of the stove. Insert the first crimped end into the stove’s flue collar, and keep each crimped end pointing toward the stove.

(Fig. 4) Using the holes in the flue collar as guides, drill 3 mm (1/8”) holes in the bottom of the first sec- tion of chimney connector and secure it to the flue collar with three #10 x 1/2” sheet metal screws.

•Secure each joint between sections of chimney connector, including

telescoping joints, with at least three (3) sheet metal screws. The pre-drilled

holes in the top of each section of chimney con- nector serve as guides when you drill 3 mm (1/8) holes in the bottom of the next section.

•Secure the chimney con-

nector to the chimney.

Fig. 4 the crimped end

Instructions for various

of the connector points

installations follow.

toward stove.

•Be sure the installed stove

and chimney connector are correct distances from nearby combustible materials.

NOTE: Special slip pipes and thimble sleeves that form telescoping joints between sections of chimney con- nector are available to simplify installations. They often eliminate the need to cut individual connector sections. Consult your local dealer about these special pieces.

Securing the Single-wall Connector to a

Prefabricated Chimney

Follow the installation instructions of the chimney manufacturer exactly as you install the chimney. The manufacturer of the chimney will supply the acces- sories to support the chimney, either from the roof of the house, at the ceiling of the room where the stove is installed, or from an exterior wall.

Special adapters are available from your local dealer to make the connection between the prefabricated chimney and the chimney connector. The top of such adapters attaches directly to the chimney or to the chimney’s ceiling support package, while the bottom of the adapter is screwed to the chimney connector.

These adapters are designed so the top end will fit outside the inner wall of the chimney, and the bottom end will fit inside the first section of chimney connector. When assembled in this way, any soot or creosote fall- ing from the inner walls of the chimney will stay inside the chimney connector.

6

30003842

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Encore Table of Contents WelcomeSpecifications Encore Model 2550CEInstallation Outside AirChimney Height Masonry Chimneys Chimney Connector GuidelinesWhat Kind of Chimney to Use Prefabricated ChimneysDouble-wall Chimney Connectors Single-wall Chimney ConnectorsFireplace Installations Securing the Single-wall Connector to a Masonry ChimneyFreestanding Installations Above the FireplaceThrough the Fireplace Wall Pass-ThroughsFloor Protection for Fireplace Installations HearthsKeep the Stove a Safe Distance From Surrounding Materials Safe Ways to Reduce Clearances Summary of ClearancesConnecting fluepipe clearances Assembly Single Air Control Regulates Heat Output and Burn Time OperationEncore Controls Damper Directs Air Flow Within the StoveAndirons Help Protect the Glass Two Ways to Add FuelInfrared Reflective Glass Panels For Clear Fire Viewing Burn Only High-Quality WoodUse the Air Control Settings That Work Best for You Encore Control SettingsSurface Thermometer is a Valuable Guide to Operation High-Efficiency Wood Burning with Catalytic Combustion Conditioning Your StoveStarting and Maintaining a Wood Fire Refuel While the Embers Are Still Hot Add larger pieces of wood as the fire begins to burn wellAsh Disposal Indoor / Outdoor location Draft ManagementSteel Chimney Flue SizingFuel Draft TestingCreosote Back-puffingMaintenance Check the Operation Primary Air Shutter Adjust the Damper as NeededHow to Adjust the Door Latches Tighten the Damper Handle as NeededCatalytic Element Inspection and Cleaning When to Suspect a Combustor ProblemInspecting the Combustor Replace the Stove Gaskets as Needed Gasket Diameter ...And the Parts it SealsAdjust the Door If Necessary Permanent Encore GasketsChimney System Creosote Annual Maintenance Appendix Catalytic Combustor Encore Woodburning Stove Encore Woodburning Stove Shell Enamel Parts Encore Color Warranty CFM Corporation

2550CE specifications

The Vermont Casting 2550CE is a remarkable wood-burning stove that embodies both efficiency and style, making it a preferred choice for those who desire a reliable heating solution combined with aesthetic appeal. This model stands out in the realm of traditional wood stoves, offering an exceptional blend of performance features and innovative technologies.

At the heart of the 2550CE is its robust cast iron construction, which contributes to superior heat retention and distribution. Cast iron is known for its ability to radiate warmth long after the fire has dwindled, ensuring a cozy atmosphere in your living space. This model also features a large ceramic glass door, providing a captivating view of the flames while allowing for easy monitoring of the fire's conditions.

One of the defining characteristics of the Vermont Casting 2550CE is its advanced secondary combustion system. This technology enhances the stove's efficiency by reburning the exhaust gases, thus extracting maximum heat from the wood and reducing emissions. This not only makes for a cleaner burn but also extends the burn time, allowing users to enjoy an extended period of warmth with fewer reloads.

The 2550CE is designed with functionality in mind, equipped with an easy-to-use air control system that enables precise regulation of airflow. This allows users to adjust the fire’s intensity based on their immediate heating needs, maximizing both comfort and fuel efficiency. Moreover, the stove’s large firebox accommodates logs up to 18 inches in length, making it practical for those who prefer to minimize the frequency of reloads.

In terms of style, the Vermont Casting 2550CE features a classic design that complements various interior decor styles, including rustic, traditional, and modern settings. Available in several finishes, including matte black and enamel options, the stove can be customized to match individual tastes and home aesthetics.

The commitment to sustainability is another significant aspect of the 2550CE. With its lower emissions rates complying with EPA standards, homeowners can enjoy a warm and inviting environment while being mindful of their environmental impact. Overall, the Vermont Casting 2550CE combines time-tested craftsmanship with modern technology, making it an ideal choice for anyone seeking an efficient and elegant wood-burning stove.
Top Page Image Contents