Vanguard Heating VMH26TN installation manual Assembling Brass Trim Brass trim shipped with mantel

Page 15

INSTALLING

Continued

Assembling Brass Trim (Brass trim shipped with mantel)

1.Remove packaging from three remaining pieces of brass trim.

2.Locate two adjusting plates with set screws, and two shims in the hardware packet.

3.Align shim under adjusting plate as shown in Figure 14.

4.Slide one end of adjusting plate/shim in slot on mitered edge of top brass trim (see Figure 14).

5.Slide other end of adjusting plate/shim in slot on mitered edge of side brass trim (see Figure 14).

6.While firmly holding edges of brass trim together, tighten both set screws on the adjusting plate with slotted screwdriver.

7.Repeat steps 1 through 6 for other corner.

8.Set Brass Assembly aside for later installation.

Top Brass Trim

Set Screws

Slot

Adjusting

 

Plate

 

Shim

Mitered Edge

Slot

Side Brass Trim

 

Figure 14 - Assembling Brass Trim

Attaching Wood Base to Solid Floor

For attaching base to solid floors (concrete or masonry)

Note: Floor anchors and mounting screws are in hardware package. The hardware package is provided with fireplace.

1.Drill holes at marked locations using 5/16" drill bit. For solid floors (concrete or masonry), drill at least 1" deep.

2.Fold floor anchor as shown in Figure 15.

Figure 15 - Folding Anchor

3.Insert floor anchor (wings first) into hole. Tap anchor flush to floor.

4.Insert mounting screws through base and into floor anchors.

5.Tighten screws until base is firmly fastened to floor.

15

102885

Page 14 Page 16
Image 15
Page 14 Page 16
Contents What to do if YOU Smell GAS OWNER’S Operation and Installation ManualContents Safety Information 001 Thermostatic Heat Control Local Codes Product Features UnpackingSafety Pilot Piezo Ignition SystemInstalling Log AssemblyConfined and Unconfined Space AIR for Combustion and VentilationProviding Adequate Ventilation Unusually Tight ConstructionDetermining if You Have a Confined or Unconfined Space Determining FRESH-AIR Flow for Fireplace LocationVentilation Air From Inside Building Ventilation AIRVentilation Air from Outdoors Shown with Optional Mantel Ventilation Air From OutdoorsLocating Fireplace InstallationInstallation Items Check GAS TypeCeiling BUILT-IN Fireplace Installation InstallingSide Firebox Mantel Shelf Mantel Clearances for Built-In InstallationAttaching Brass Trim to Fireplace Optional Mantel InstallationAttaching Wood Base to Solid Floor Assembling Brass Trim Brass trim shipped with mantelGas Connection Connecting to GAS SupplyInstallation Items Needed Connecting Fireplace to GAS SupplyPressure Testing GAS Supply Piping System Pressure Testing Fireplace GAS ConnectionsChecking GAS Connections Operating Fireplace Pilot Operating Fireplace Shutting Off FireplaceShutting Off Burner Only pilot stays lit Pilot Flame Pattern Inspecting BurnerCorrect Burner Flame Pattern Burner Flame PatternCleaning and Maintenance Trouble Shooting ODS/PILOT and BurnerCabinet TROUBLE- Shooting See CleaningCleaning and Mainte Top Ing statement atParts Not Under Warranty Technical ServiceService Hints Parts Under WarrantyUnfinished GM921U Finished GM920F AccessoriesValve GA5010 GA3400TVMH26TN Model VMH26TN Parts ListKeep this Warranty Warranty Information

VMH26TN specifications

The Vanguard Heating VMH26TN is a cutting-edge heating unit designed to provide efficient and consistent warmth for residential and commercial spaces. With its sleek design and advanced technology, this model has garnered attention for its reliability and performance.

One of the standout features of the VMH26TN is its powerful heating capability. It boasts a maximum output of 26,000 BTUs, making it suitable for heating medium to large rooms with ease. This makes it an ideal choice for living spaces, offices, and even workshops that require a dependable source of heat during the colder months.

The unit incorporates innovative heating technologies that enhance its efficiency. It utilizes a high-efficiency burner system that maximizes fuel consumption, thereby reducing energy costs. The VMH26TN is designed to operate with minimal emissions, making it an environmentally friendly option for those conscious of their carbon footprint.

The VMH26TN features a user-friendly digital thermostat that allows users to easily set their desired temperature. The thermostat ensures precise temperature control, helping to maintain a consistent and comfortable environment. Additionally, the unit includes programmable settings that enable users to schedule heating times according to their lifestyle, optimizing energy use and comfort.

Another critical characteristic of the VMH26TN is its robust construction. Built from high-quality materials, this heating unit is designed for durability and longevity, providing peace of mind for users. Its compact design ensures that it can fit into various spaces without compromising on performance.

Safety features are also a priority in the VMH26TN design. It includes an automatic shut-off function that activates in case of overheating or other malfunctions, protecting both the unit and your space. The built-in safety sensors monitor the operation continuously to ensure optimal functionality while minimizing risks.

In summary, the Vanguard Heating VMH26TN combines powerful heating capacity, advanced efficiency technology, and user-friendly features in a robust and safe design. Whether for a home or commercial setting, this heating unit stands out as a reliable choice for anyone looking to achieve warmth and comfort efficiently.
Top Page Image Contents