Vanguard Heating VMH26TN Connecting Fireplace to GAS Supply, Installation Items Needed

Page 17

CONNECTING TO GAS SUPPLY

Continued

CONNECTING FIREPLACE TO GAS SUPPLY

Installation Items Needed

•Phillips screwdriver

•sealant (resistant to propane gas, not provided)

1.Remove fireplace screen. Remove two screws that hold fireplace screen in place for shipping. These screws are located near top of screen. Discard screws. Lift fireplace screen up and pull out to remove.

2.Remove screws that attach branch support to fireplace (see Figure 17). Care- fully lift up branch support and remove from fireplace (see Figure 17).

Figure 17 - Removing Twig Support From Fireplace

3.Route flexible gas line from manual shutoff valve into fireplace through side or rear access holes in outer casing. Route flexible gas supply line through fireplace access holes in outer casing.

NOTICE

Most building codes do not permit concealed gas connections. A flexible gas line is provided to allow accessibility from the fireplace. The flexible gas supply line connection to the manual shutoff valve should be accessible.

4.Apply pipe joint sealant lightly to male threads of gas connector attached to flexible gas line (see Figure 18). Connect flexible gas line to flexible gas line attached to gas regulator of fireplace (see Figure 18).

5.Check all gas connections for leaks. See Checking Gas Connections, below.

6.Replace branch support back into fireplace. Feed flexible gas line into fireplace base area while replacing branch support. Make sure the entire flexible gas line is in fireplace base area. Reattach branch support to fireplace with screws removed in step 3.

To Fireplace

➞

 

 

 

 

 

 

 

 

 

Gas Regulator

Gas Connector

Manual Shutoff Valve

 

 

 

Flexible Gas Line

 

 

 

To Gas

from Fireplace Gas

 

 

 

Flexible Gas Line from

➞

Supply

Regulator

 

 

 

 

 

Manual Shutoff Valve

Figure 18 - Attaching Flexible Gas Lines Together

Continued 17

102885

Page 16 Page 18
Image 17
Page 16 Page 18
Contents What to do if YOU Smell GAS OWNER’S Operation and Installation ManualContents Safety Information 001 Safety Pilot Local Codes Product Features UnpackingPiezo Ignition System Thermostatic Heat ControlInstalling Log AssemblyProviding Adequate Ventilation AIR for Combustion and VentilationUnusually Tight Construction Confined and Unconfined SpaceDetermining if You Have a Confined or Unconfined Space Determining FRESH-AIR Flow for Fireplace LocationVentilation Air From Inside Building Ventilation AIRVentilation Air from Outdoors Shown with Optional Mantel Ventilation Air From OutdoorsInstallation Items InstallationCheck GAS Type Locating FireplaceCeiling BUILT-IN Fireplace Installation InstallingSide Firebox Mantel Shelf Mantel Clearances for Built-In InstallationAttaching Brass Trim to Fireplace Optional Mantel InstallationAttaching Wood Base to Solid Floor Assembling Brass Trim Brass trim shipped with mantelGas Connection Connecting to GAS SupplyInstallation Items Needed Connecting Fireplace to GAS SupplyChecking GAS Connections Pressure Testing GAS Supply Piping SystemPressure Testing Fireplace GAS Connections Operating Fireplace Pilot Shutting Off Burner Only pilot stays lit Operating FireplaceShutting Off Fireplace Pilot Flame Pattern Inspecting BurnerCorrect Burner Flame Pattern Burner Flame PatternCabinet Cleaning and Maintenance Trouble ShootingODS/PILOT and Burner TROUBLE- Shooting See CleaningCleaning and Mainte Top Ing statement atService Hints Technical ServiceParts Under Warranty Parts Not Under WarrantyValve GA5010 AccessoriesGA3400T Unfinished GM921U Finished GM920FVMH26TN Model VMH26TN Parts ListKeep this Warranty Warranty Information

VMH26TN specifications

The Vanguard Heating VMH26TN is a cutting-edge heating unit designed to provide efficient and consistent warmth for residential and commercial spaces. With its sleek design and advanced technology, this model has garnered attention for its reliability and performance.

One of the standout features of the VMH26TN is its powerful heating capability. It boasts a maximum output of 26,000 BTUs, making it suitable for heating medium to large rooms with ease. This makes it an ideal choice for living spaces, offices, and even workshops that require a dependable source of heat during the colder months.

The unit incorporates innovative heating technologies that enhance its efficiency. It utilizes a high-efficiency burner system that maximizes fuel consumption, thereby reducing energy costs. The VMH26TN is designed to operate with minimal emissions, making it an environmentally friendly option for those conscious of their carbon footprint.

The VMH26TN features a user-friendly digital thermostat that allows users to easily set their desired temperature. The thermostat ensures precise temperature control, helping to maintain a consistent and comfortable environment. Additionally, the unit includes programmable settings that enable users to schedule heating times according to their lifestyle, optimizing energy use and comfort.

Another critical characteristic of the VMH26TN is its robust construction. Built from high-quality materials, this heating unit is designed for durability and longevity, providing peace of mind for users. Its compact design ensures that it can fit into various spaces without compromising on performance.

Safety features are also a priority in the VMH26TN design. It includes an automatic shut-off function that activates in case of overheating or other malfunctions, protecting both the unit and your space. The built-in safety sensors monitor the operation continuously to ensure optimal functionality while minimizing risks.

In summary, the Vanguard Heating VMH26TN combines powerful heating capacity, advanced efficiency technology, and user-friendly features in a robust and safe design. Whether for a home or commercial setting, this heating unit stands out as a reliable choice for anyone looking to achieve warmth and comfort efficiently.
Top Page Image Contents