Vanguard Heating VMH26TN installation manual Pilot

Page 20

OPERATING FIREPLACE

Continued

20

4.Wait five (5) minutes to clear out any gas. Then smell for gas, including near the floor. If you smell gas, STOP! Follow “B” in the safety information at the top of page 19. If you don’t smell gas, go to the next step.

5.Turn control knob counterclockwise C-clockwiseto the PILOT position. Press in control knob for five (5) seconds (see Figure 19, page 19).

Note: You may be running this fireplace for the first time after hooking up to gas supply. If so, the control knob may need to be pressed in for 30 seconds. This will allow air to bleed from the gas system.

•If control knob does not pop up when released, contact a qualified service person or gas supplier for repairs.

6.With control knob pressed in, push down and release ignitor button. This will light pilot. The pilot is attached to the front of burner. If needed, keep pressing ignitor button until pilot lights.

Note: If pilot does not stay lit, refer to Troubleshooting, pages 24 through

27.Also contact a qualified service person or gas supplier for repairs. Until repairs are made, light pilot with match. To light pilot with match, see Manual Lighting Procedure, page 21.

7.Keep control knob pressed in for 30 seconds after lighting pilot. After 30 seconds, release control knob.

Ignitor Electrode

Thermocouple

Pilot Burner

Figure 22 - Pilot

Note: If pilot goes out, repeat steps 3 through 7. This fireplace has a safety interlock system. Wait one (1) minute before lighting pilot again.

8.Turn control knob counterclockwise C-clockwiseto desired heating level. The main burner should light. Set control knob to any heat level between HI

and LO.

CAUTION

WARNING ICON

G 001

Do not try to adjust heating levels by using the manual shutoff valve.

102885

Page 19 Page 21
Image 20
Page 19 Page 21
Contents OWNER’S Operation and Installation Manual What to do if YOU Smell GASContents Safety Information 001 Local Codes Product Features Unpacking Safety PilotPiezo Ignition System Thermostatic Heat ControlAssembly Installing LogAIR for Combustion and Ventilation Providing Adequate VentilationUnusually Tight Construction Confined and Unconfined SpaceDetermining FRESH-AIR Flow for Fireplace Location Determining if You Have a Confined or Unconfined SpaceVentilation AIR Ventilation Air From Inside BuildingVentilation Air From Outdoors Ventilation Air from Outdoors Shown with Optional MantelInstallation Installation ItemsCheck GAS Type Locating FireplaceCeiling Installing BUILT-IN Fireplace InstallationMantel Clearances for Built-In Installation Side Firebox Mantel ShelfOptional Mantel Installation Attaching Brass Trim to FireplaceAssembling Brass Trim Brass trim shipped with mantel Attaching Wood Base to Solid FloorConnecting to GAS Supply Gas ConnectionConnecting Fireplace to GAS Supply Installation Items NeededChecking GAS Connections Pressure Testing GAS Supply Piping SystemPressure Testing Fireplace GAS Connections Operating Fireplace Pilot Shutting Off Burner Only pilot stays lit Operating FireplaceShutting Off Fireplace Inspecting Burner Pilot Flame PatternBurner Flame Pattern Correct Burner Flame PatternCabinet Cleaning and Maintenance Trouble ShootingODS/PILOT and Burner See Cleaning TROUBLE- ShootingCleaning and Mainte Ing statement at TopTechnical Service Service HintsParts Under Warranty Parts Not Under WarrantyAccessories Valve GA5010GA3400T Unfinished GM921U Finished GM920FVMH26TN Parts List Model VMH26TNWarranty Information Keep this Warranty

VMH26TN specifications

The Vanguard Heating VMH26TN is a cutting-edge heating unit designed to provide efficient and consistent warmth for residential and commercial spaces. With its sleek design and advanced technology, this model has garnered attention for its reliability and performance.

One of the standout features of the VMH26TN is its powerful heating capability. It boasts a maximum output of 26,000 BTUs, making it suitable for heating medium to large rooms with ease. This makes it an ideal choice for living spaces, offices, and even workshops that require a dependable source of heat during the colder months.

The unit incorporates innovative heating technologies that enhance its efficiency. It utilizes a high-efficiency burner system that maximizes fuel consumption, thereby reducing energy costs. The VMH26TN is designed to operate with minimal emissions, making it an environmentally friendly option for those conscious of their carbon footprint.

The VMH26TN features a user-friendly digital thermostat that allows users to easily set their desired temperature. The thermostat ensures precise temperature control, helping to maintain a consistent and comfortable environment. Additionally, the unit includes programmable settings that enable users to schedule heating times according to their lifestyle, optimizing energy use and comfort.

Another critical characteristic of the VMH26TN is its robust construction. Built from high-quality materials, this heating unit is designed for durability and longevity, providing peace of mind for users. Its compact design ensures that it can fit into various spaces without compromising on performance.

Safety features are also a priority in the VMH26TN design. It includes an automatic shut-off function that activates in case of overheating or other malfunctions, protecting both the unit and your space. The built-in safety sensors monitor the operation continuously to ensure optimal functionality while minimizing risks.

In summary, the Vanguard Heating VMH26TN combines powerful heating capacity, advanced efficiency technology, and user-friendly features in a robust and safe design. Whether for a home or commercial setting, this heating unit stands out as a reliable choice for anyone looking to achieve warmth and comfort efficiently.
Top Page Image Contents