Jotul F 3 operating instructions Clearances to Combustibles, Floor Protection, U.S.and Canada

Page 10

CLEARANCES TO COMBUSTIBLES

Floor Protection

Floor protection under the F 3 CB woodstove, must be one of the following:

1.Any non combustible material with an insulative R value of 1.1.

2.Any UL, ULC or WH hearth board or prefrabricated non-combustible material.

The bottom heatshield (standard equipment) is required in all installations.

Individual sections of floor protection must be mortared together to prevent sparks from falling through to combustible materials. Any carpeting must be removed from under the floor protection.

In the U.S.and Canada

The F 3 CB must be installed on a non-combustible surface extending a minimum of 18” (460mm) in front of the stove and 8” (200mm) on the remaining sides of the stove (measured from side and back panels).

This will result in a minimum floor protection of

41 D X 39 W See figure 12.

In a rear vent installation the floor protection must also extend under the stove pipe a minimum of 2” (50mm) beyond either side of the pipe.

8”

200mm

41”

8”

 

 

 

8”

DEEP

200mm

 

 

 

200mm

 

 

 

 

 

 

 

 

 

18”

 

 

 

 

 

 

front

460mm

 

 

 

 

 

 

 

 

 

 

39”

WIDE

FIGURE12

Clearances to walls and ceilings

The following clearances have been tested to UL and ULC standards and are the minimum clearances specifically established for the Jøtul F 3 CB.

The following charts and diagrams give the required clearances you must maintain when installing the F 3 CB near combustible surfaces.

A combustible surface is anything that can burn (i.e. sheet rock, wall paper, wood, fabrics etc.). These surfaces are not limited to those that are visible and also include materials that are behind non-combustible materials.

If you are not sure of the combustible nature of a material, consult your local fire officials.

Remember: “Fire Resistant” materials are considered combustible; they are difficult to ignite, but will burn. Also “Fire-rated” sheet rock is also considered combustible.

Contact your local building officials about restrictions and installation requirements in your area.

Using Shields to Reduce Clearances

Pipe shields: When using listed pipe shields to reduce the connector clearance to combustibles, it must start 1” above the lowest exposed point of the connect pipe and extend vertically a minimum of 25” above the top surface of the stove.

Double wall pipe: Listed double wall pipe is an acceptable alternative to connector pipe heatshields.

Wall-Mounted Protection: When reducing clearances through the use of wall mounted protection:

In the U.S. refer to NFPA 211, Standard for Chimneys, Fireplaces, Vents and Solid Fuel Burning Appliances, for acceptable materials, proper sizing and construction guidelines.

In Canada, refer to CAN/CSA-B365, Installation Code for Solid-Fuel Burning Appliances and Equipment, also for acceptable materials, proper sizing and construction guidelines.

Stove mounted Rear Heatshield is standard equipment on all F 3 CB woodstoves. NO OTHER STOVE MOUNTED HEAT SHIELD MAY BE USED.

10

Image 10
Contents Jøtul F 3 CB Woodstove Table of Contents F 3 CB wood stove has been tested and listed to StandardsJøtul F 3 CB Woodstove Installation ReminderDo not use the connector pipe as a chimney Side Exit VentingChimney Requirements Masonry ChimneysU.S Chimney HeightWall PASS-THROUGHS Common MethodSee .3.1 and 5.3.2 of CAN/CSA B365-M91 Connecting to the ChimneyCanada Masonry ChimneyPrefabricated Chimneys Hearth-mount into a Masonry FireplaceSee figures 10 Floor Protection Using Shields to Reduce ClearancesClearances to Combustibles U.S.and CanadaStove Clearances Unprotected Surfaces Connector Unprotected Surface Protected Surface ClearancesSide Rear Corner Mantel ClearancesWall Shields for Close Clearance Height above the top of the stove = 40 1015mm AlcoveAlcove ceiling above top of stove = 40 1015mm Coal Treated or painted wood Garbage OperationDo Not Burn Controls on the F 3 CBCool the stove to room temperature Adding FuelGlass Care MaintenanceFormation of Creosote Rinse and dry glass completely, before burning your stoveGeneral Maintenance Gaskets Gasket List for the F 3 CBAccessories Floor Bracket KitExploded THEF3CB Parts List Jøtul ASA

F 3 specifications

The Jotul F 3 is a classic wood stove that embodies the perfect blend of traditional design and modern engineering. Renowned for its efficiency and durability, this model has become a favorite among homeowners looking for an effective heating solution with aesthetic appeal.

One of the standout features of the Jotul F 3 is its efficient combustion system. This stove employs a unique primary and secondary combustion system that allows for a cleaner burn, producing minimal emissions. This technology not only enhances the stove's efficiency but also contributes to a reduced environmental footprint, making it an excellent choice for eco-conscious consumers.

In terms of design, the Jotul F 3 is crafted from cast iron, a material known for its longevity and heat retention properties. This construction allows the stove to radiate warmth long after the fire has died down, providing consistent heating throughout the day and evening. The stove is available in several finishes, including classic black and a striking blue-black enamel, enabling it to seamlessly fit into various interior styles, from rustic to contemporary.

The Jotul F 3 also includes a large glass window that offers an unobstructed view of the flames, enhancing the cozy ambiance of any room. The airwash system keeps the glass clean, ensuring a clear view of the fire while minimizing the need for frequent cleaning.

With a heating capacity of up to 1,800 square feet, the Jotul F 3 is ideal for both small and medium-sized spaces. Its compact size does not compromise on performance, and it features a sizable firebox that allows for extended burn times, meaning less frequent refueling.

Another notable characteristic of the Jotul F 3 is its user-friendly design. The stove includes easy-to-use controls for adjusting the airflow, allowing users to optimize the burn rate and heat output based on their preferences.

In conclusion, the Jotul F 3 is a versatile and efficient wood stove that combines classic aesthetics with modern technology. Its high combustion efficiency, durable cast iron construction, and elegant design make it a sought-after choice for anyone seeking warmth and beauty in their home. With its commitment to both functionality and style, the Jotul F 3 stands out as an exemplary heating solution that will serve homeowners for years to come.