Jotul F 3 Canada, See .3.1 and 5.3.2 of CAN/CSA B365-M91, Connecting to the Chimney

Page 8

FIGURE7

In Canada

The Canada the standard has been established by the Canadian Standard Association. The installation must conform to CAN/CSA-B365, Installation Code for Solid Fuel Burning Appliances and Equipment. Before proceeding be sure to consult your local building inspector.

Common Method

This method requires the removal of all combustible materials from at least 18” (457mm) around the chimney connector’s proposed location. With a 6” round liner the minimum area required would be 43” x 43” square.

It is important to remember to locate the pass-through at least 25” from the ceiling to maintain the proper clearance to combustibles.

The space that is cleared of combustible materials must then remain empty. Sheet metal panels can then be used to cover the area. However, when using a panel on both sides of the wall each cover must be installed on noncombustible spacers at least 1” from the wall. If one panel of sheet metal is to be used it may be installed flush to the wall.

SEE SECTION 5.3.1 and 5.3.2 of CAN/CSA - B365-M91.

Consult your local building inspector, authorized Jøtul Dealer, NFPA 211 in the U.S. or CAN/CSA-B635 in Canada for other approved wall pass-through methods.

CONNECTING TO THE CHIMNEY

Masonry Chimney

When installing a F 3 CB into a masonry chimney through a “thimble”(the opening through the chimney wall to the flue), the thimble must be lined with ceramic tile or metal and be securely cemented in place.

The chimney connector/stove pipe must slide completely inside the thimble to the inner surface or the flue liner. It may be necessary to make use of a thimble sleeve (a pipe with a slightly smaller diameter than standard stove pipe). This special pipe can be easily installed into a thimble. See figure 8.

Make sure the connector pipe or thimble sleeve does not protrude into the flue liner, thereby restricting the area the smoke has to flow through. This bottle-neck will have a negative affect on the chimney system.

The chimney connector should be sealed at the thimble with refractory cement and the stove pipe leading to the stove should have a minimum of three screws.

DO NOT CONNECT THIS STOVE TO A CHIMNEY FLUE SERVICING ANOTHER APPLIANCE OF ANY KIND.

Connector pipe shall be flush with the inside of the flue tile

Stove pipe connector

Flue tile

FIGURE8 Thimble

8

Image 8
Contents Jøtul F 3 CB Woodstove Table of Contents Jøtul F 3 CB Woodstove StandardsF 3 CB wood stove has been tested and listed to Installation ReminderDo not use the connector pipe as a chimney Side Exit VentingChimney Requirements Masonry ChimneysChimney Height Wall PASS-THROUGHSU.S Common MethodConnecting to the Chimney CanadaSee .3.1 and 5.3.2 of CAN/CSA B365-M91 Masonry ChimneySee figures 10 Hearth-mount into a Masonry FireplacePrefabricated Chimneys Using Shields to Reduce Clearances Clearances to CombustiblesFloor Protection U.S.and CanadaConnector Unprotected Surface Protected Surface Clearances Side Rear CornerStove Clearances Unprotected Surfaces Mantel ClearancesWall Shields for Close Clearance Alcove ceiling above top of stove = 40 1015mm AlcoveHeight above the top of the stove = 40 1015mm Operation Do Not BurnCoal Treated or painted wood Garbage Controls on the F 3 CBCool the stove to room temperature Adding FuelMaintenance Formation of CreosoteGlass Care Rinse and dry glass completely, before burning your stoveGeneral Maintenance Gaskets Gasket List for the F 3 CBAccessories Floor Bracket KitExploded THEF3CB Parts List Jøtul ASA

F 3 specifications

The Jotul F 3 is a classic wood stove that embodies the perfect blend of traditional design and modern engineering. Renowned for its efficiency and durability, this model has become a favorite among homeowners looking for an effective heating solution with aesthetic appeal.

One of the standout features of the Jotul F 3 is its efficient combustion system. This stove employs a unique primary and secondary combustion system that allows for a cleaner burn, producing minimal emissions. This technology not only enhances the stove's efficiency but also contributes to a reduced environmental footprint, making it an excellent choice for eco-conscious consumers.

In terms of design, the Jotul F 3 is crafted from cast iron, a material known for its longevity and heat retention properties. This construction allows the stove to radiate warmth long after the fire has died down, providing consistent heating throughout the day and evening. The stove is available in several finishes, including classic black and a striking blue-black enamel, enabling it to seamlessly fit into various interior styles, from rustic to contemporary.

The Jotul F 3 also includes a large glass window that offers an unobstructed view of the flames, enhancing the cozy ambiance of any room. The airwash system keeps the glass clean, ensuring a clear view of the fire while minimizing the need for frequent cleaning.

With a heating capacity of up to 1,800 square feet, the Jotul F 3 is ideal for both small and medium-sized spaces. Its compact size does not compromise on performance, and it features a sizable firebox that allows for extended burn times, meaning less frequent refueling.

Another notable characteristic of the Jotul F 3 is its user-friendly design. The stove includes easy-to-use controls for adjusting the airflow, allowing users to optimize the burn rate and heat output based on their preferences.

In conclusion, the Jotul F 3 is a versatile and efficient wood stove that combines classic aesthetics with modern technology. Its high combustion efficiency, durable cast iron construction, and elegant design make it a sought-after choice for anyone seeking warmth and beauty in their home. With its commitment to both functionality and style, the Jotul F 3 stands out as an exemplary heating solution that will serve homeowners for years to come.