Jotul F 3 operating instructions CB Parts List

Page 20

F 3 CB PARTS LIST

2Inner rear heatshield

2B Outer rear heatshield

6Smoke outlet cover

7Traverse bar

8Top plate with smoke cover

11 Baffle plate

12 Air distributor

15 Back plate

22 Side plate

23 Back burn plate

24 Right burn plate

26 Air deflector

28 Sliding air vent

29 Front plate

31 Log retainer

35 Door

37 Hinge pin

40 Start-up air vent

42 Door handle complete

43 Locking bar

45 Glass

46 Sparkscreen

51 Ashlip

52 Leg

55 Bottom plate

57 Inner bottom plate

59 Left burn plate

62 Secondary air cover

64 Flat ash housing gasket

65 Ash housing

70 Ashpan

76 Ashpan door

73 Stove tool

78 Door latch

79 Bottom heatshield

ONLY USE REPLACEMENTS PARTS

PROVIDED THROUGH YOUR AUTHORIZED JØTUL DEALER.

APPENDIX A:

ALTERNATE FLOOR PROTECTION

All floor protection materials must be non-combustible ie. metal, brick, stone, mineral fiber boards). Any combustible material may not be used.

The easiest means of determining if a proposed alternate floor material meets requirements listed in this manual is to follow this procedure.

R-value = thermal resistance k-value = thermal conductivity C-value = thermal conductance

1.Convert the specification to R-value;

a.If R-value is given, no conversion is

needed.

b.If k-value is given with a required thickness (T) in inches: R=1/k X T.

c.If C-value is given: R=1/C.

2.Determine the R-value of the proposed alternate floor protector.

a.Use the formula in Step 1 to convert values not expressed as “R”.

b.For multiple layers, add R-values of each layer to determine overall R-value.

3.If the overall R-value of the sustem is greater than the R-value of the specified floor protector, the alternate is acceptable.

EXAMPLE:

The specified floor protector should be 3/4” thick material with a k-factor of 0.84. The proposed alternate is 4” brick with a C- factor of 1.25 over

1/8” mineral board witha k-factor of 0.29.

Step A. Use formula above to convert specifications to R-value. R=1/k X T= 1/.84 X .75 = .893

Step B. Calculate R of proposed system. 4” brick of C-1.25, therefore

R brick = 1/C = 1/1.25 = 0.80.

1/8” mineral board of k = 0.29 therefore R mineral board = 1/.29 X 0.125 = 0.431

Total R = R brick + R mineral board= 0.8 + 0.431=1.231

Step C. Compare proposed system R = 1.231 to specified R of 0.893. Since R is greater than required, the system is acceptable.

Definitions:

Thermal conductance =

 

 

 

 

 

Btu

 

=

W

 

 

C = (hr)(ft2)(F)

 

(m2)(K)

 

Thermal conductivity =

 

 

 

 

k =

Btu

=

 

W

=

(Btu)

(hr)(ft2)(F)

 

 

(m2)(K)

 

(hr)(ft)(F)

Thermal resistance =

 

 

 

 

 

 

Btu

 

=

(m2)(K)

= (Btu)(inch)

R = (hr)(ft2)(F)

 

W

 

(hr)(ft2)(F)

FOR THE JØTUL F 3 CB WOOD STOVE REQUIRES FLOOR PROTECTION WITH A MINIMUM INSULATING

R VALUE OF 1.1.

ALCOVE INSTALLATION REQUIRE A MINIMUM R VALUE OF 1.1. (IF A UL/ULC or WHI LISTED HEARTH PAD IS NOT USED.)

20

Page 19 Page 21
Image 20
Page 19 Page 21
Contents Jøtul F 3 CB Woodstove Table of Contents Jøtul F 3 CB Woodstove StandardsF 3 CB wood stove has been tested and listed to Installation ReminderDo not use the connector pipe as a chimney Side Exit VentingChimney Requirements Masonry ChimneysChimney Height Wall PASS-THROUGHSU.S Common MethodConnecting to the Chimney CanadaSee .3.1 and 5.3.2 of CAN/CSA B365-M91 Masonry ChimneySee figures 10 Hearth-mount into a Masonry FireplacePrefabricated Chimneys Using Shields to Reduce Clearances Clearances to CombustiblesFloor Protection U.S.and CanadaConnector Unprotected Surface Protected Surface Clearances Side Rear CornerStove Clearances Unprotected Surfaces Mantel ClearancesWall Shields for Close Clearance Alcove ceiling above top of stove = 40 1015mm AlcoveHeight above the top of the stove = 40 1015mm Operation Do Not BurnCoal Treated or painted wood Garbage Controls on the F 3 CBCool the stove to room temperature Adding FuelMaintenance Formation of CreosoteGlass Care Rinse and dry glass completely, before burning your stoveGeneral Maintenance Gaskets Gasket List for the F 3 CBAccessories Floor Bracket KitExploded THEF3CB Parts List Jøtul ASA

F 3 specifications

The Jotul F 3 is a classic wood stove that embodies the perfect blend of traditional design and modern engineering. Renowned for its efficiency and durability, this model has become a favorite among homeowners looking for an effective heating solution with aesthetic appeal.

One of the standout features of the Jotul F 3 is its efficient combustion system. This stove employs a unique primary and secondary combustion system that allows for a cleaner burn, producing minimal emissions. This technology not only enhances the stove's efficiency but also contributes to a reduced environmental footprint, making it an excellent choice for eco-conscious consumers.

In terms of design, the Jotul F 3 is crafted from cast iron, a material known for its longevity and heat retention properties. This construction allows the stove to radiate warmth long after the fire has died down, providing consistent heating throughout the day and evening. The stove is available in several finishes, including classic black and a striking blue-black enamel, enabling it to seamlessly fit into various interior styles, from rustic to contemporary.

The Jotul F 3 also includes a large glass window that offers an unobstructed view of the flames, enhancing the cozy ambiance of any room. The airwash system keeps the glass clean, ensuring a clear view of the fire while minimizing the need for frequent cleaning.

With a heating capacity of up to 1,800 square feet, the Jotul F 3 is ideal for both small and medium-sized spaces. Its compact size does not compromise on performance, and it features a sizable firebox that allows for extended burn times, meaning less frequent refueling.

Another notable characteristic of the Jotul F 3 is its user-friendly design. The stove includes easy-to-use controls for adjusting the airflow, allowing users to optimize the burn rate and heat output based on their preferences.

In conclusion, the Jotul F 3 is a versatile and efficient wood stove that combines classic aesthetics with modern technology. Its high combustion efficiency, durable cast iron construction, and elegant design make it a sought-after choice for anyone seeking warmth and beauty in their home. With its commitment to both functionality and style, the Jotul F 3 stands out as an exemplary heating solution that will serve homeowners for years to come.
Top Page Image Contents