Jotul F 3 operating instructions Cool the stove to room temperature, Adding Fuel

Page 15

Complete the following steps for the proper break-in procedure for the F 3 CB:

1.Light a small fire, newspaper and kindling only,

only allow the stove to reach a maximum surface temperature of 200°. Burn for approximately 1 hour.

2.Allow stove to cool to room temperature.

3.Light a second fire, allowing the stove to reach a maximum temperature of 300° for 1 hour.

4.Cool the stove to room temperature.

5.Light a third fire and gradually allow the stove to reach a surface temperature of 400°

6.Cool stove to room temperature. This completes the “break-in” procedure.

Never allow the stove to exceed a 400° surface temperature during any “break-in fire” with the exception of the last “break-in” fire.

Note: IT IS NORMAL for a new painted stove to emit an odor and even smoke during its first several fires. This is caused by the seasoning of the high temperature paint and will diminish with each fire and will eventually disappear. Opening a window or door to provide additional ventilation will reduce the odor as this process takes its course.

NEVEROVERFIRETHESTOVE.

IFANYPART OF THE STOVE OR CHIMNEY GLOWS, YOU ARE OVERFIRING, AND A HOUSE FIRE OR SERIOUS DAMAGE TO THE STOVE OR CHIMNEYCOULD RESULT. IMMEDIATELYCLOSE DOWN THE AIR CONTROL IF YOU NOTICE THIS CONDITION.

Starting and Maintaining a Fire

Burn only solid wood directly on the bottom grate of the stove, do not elevate the fire in any way.

The ash pan door on the stove must always be securely closed when the stove is in operation.

Burning the stove with the ashpan open will over-fire the stove and cause interior damage.

With the primary air control lever and the start-up air control lever in the full open position (far right), start

with several sheets of crumbled newspaper placed directly on the grate. On top of the newspaper, place several pieces of small dry kindling (approx. 1” in diameter) with two to three larger logs (approx. 3” to 5” in diameter) on top.

Light the fire and close the door, slowly building the fire by adding larger and larger logs. Close the start- up air contrlo lever after the fire is established and new fuel lights easily. Be sure to follow the break-in procedure before creating a fire that will damage the stove.

Once the stove has reached a surface temperature range of between 400° and 600°, adjust the primary air control lever as necessary to generate the heat output and burn time desired.

Jøtul recommends the use of a magnetic stove top thermometer to monitor the surface temperature of the stove. The optimum surface temperature range for the most efficient burn is between 400° and 600°. See figure 16 below for the optimum locations of a stove-top thermometer.

stove top

stove top

thermometer

thermometer

 

FIGURE16

Adding Fuel

When reloading the stove while it is still hot and a bed of hot embers still exist, follow this reloading procedure:

·Always wear gloves when tending to the stove.

·Push the air control lever to the full open position (far right).

·Wait a few seconds before opening the door.

·Use a stove tool or poker to distribute the hot embers equally around the firebox.

·Load the fuel, usually with smaller logs first.

·Close the door, be sure to latch the door tightly.

·Wait 5 – 10 minutes before adjusting the primary air to the desired heat output setting.

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Jøtul F 3 CB Woodstove Table of Contents Standards F 3 CB wood stove has been tested and listed toJøtul F 3 CB Woodstove Reminder InstallationSide Exit Venting Do not use the connector pipe as a chimneyMasonry Chimneys Chimney RequirementsCommon Method Chimney HeightWall PASS-THROUGHS U.SMasonry Chimney Connecting to the ChimneyCanada See .3.1 and 5.3.2 of CAN/CSA B365-M91Hearth-mount into a Masonry Fireplace Prefabricated ChimneysSee figures 10 U.S.and Canada Using Shields to Reduce ClearancesClearances to Combustibles Floor ProtectionMantel Clearances Connector Unprotected Surface Protected Surface ClearancesSide Rear Corner Stove Clearances Unprotected SurfacesWall Shields for Close Clearance Alcove Height above the top of the stove = 40 1015mmAlcove ceiling above top of stove = 40 1015mm Controls on the F 3 CB OperationDo Not Burn Coal Treated or painted wood GarbageAdding Fuel Cool the stove to room temperatureRinse and dry glass completely, before burning your stove MaintenanceFormation of Creosote Glass CareGasket List for the F 3 CB General Maintenance GasketsFloor Bracket Kit AccessoriesTHEF3 ExplodedCB Parts List Jøtul ASA

F 3 specifications

The Jotul F 3 is a classic wood stove that embodies the perfect blend of traditional design and modern engineering. Renowned for its efficiency and durability, this model has become a favorite among homeowners looking for an effective heating solution with aesthetic appeal.

One of the standout features of the Jotul F 3 is its efficient combustion system. This stove employs a unique primary and secondary combustion system that allows for a cleaner burn, producing minimal emissions. This technology not only enhances the stove's efficiency but also contributes to a reduced environmental footprint, making it an excellent choice for eco-conscious consumers.

In terms of design, the Jotul F 3 is crafted from cast iron, a material known for its longevity and heat retention properties. This construction allows the stove to radiate warmth long after the fire has died down, providing consistent heating throughout the day and evening. The stove is available in several finishes, including classic black and a striking blue-black enamel, enabling it to seamlessly fit into various interior styles, from rustic to contemporary.

The Jotul F 3 also includes a large glass window that offers an unobstructed view of the flames, enhancing the cozy ambiance of any room. The airwash system keeps the glass clean, ensuring a clear view of the fire while minimizing the need for frequent cleaning.

With a heating capacity of up to 1,800 square feet, the Jotul F 3 is ideal for both small and medium-sized spaces. Its compact size does not compromise on performance, and it features a sizable firebox that allows for extended burn times, meaning less frequent refueling.

Another notable characteristic of the Jotul F 3 is its user-friendly design. The stove includes easy-to-use controls for adjusting the airflow, allowing users to optimize the burn rate and heat output based on their preferences.

In conclusion, the Jotul F 3 is a versatile and efficient wood stove that combines classic aesthetics with modern technology. Its high combustion efficiency, durable cast iron construction, and elegant design make it a sought-after choice for anyone seeking warmth and beauty in their home. With its commitment to both functionality and style, the Jotul F 3 stands out as an exemplary heating solution that will serve homeowners for years to come.
Top Page Image Contents