Enerco HSBF10LP, MHBF6LP Placing Heater on Mounting Bracket, Installing Bottom Mounting Screws

Page 7

1.Drill holes at marked locations using 5/16” drill bit. For solid walls (concrete or masonry), drill at least 1” deep.

2.Fold wall anchor as shown in figure 8 below.

Figure 8.

3.Insert wall anchor (wings first) into hole. Tap anchor flush to wall.

4.For thin walls (1/2” or less) insert red key into wall anchor.

5.Place mounting bracket onto wall. Line up holes on each end of bracket with wall anchors.

6.Insert mounting screws through bracket and into wall anchors.

7.Tighten screws until mounting bracket is firmly fastened to wall.

Placing Heater on Mounting Bracket

1.Locate two horizontal slots on back pane of heater (see figure 19).

2.Place heater onto mounting bracket. Slide hori- zontal slots onto stand-out tabs on mounting bracket.

Figure 9

Horizontal Slots

Mounting Bracket mounted to wall

Installing Bottom Mounting Screws

1.Locate two bottom mounting holes. These holes are near bottom on back panel of heater (see figure 10).

Figure 10

2.Mark screws locations on wall.

3.Remove heater from mounting bracket.

4.If installing bottom mounting screw into hollow

or solid wall, install wall anchors. Follow steps 1 through 4 under Attaching to Wall using Anchor. If installing bottom mounting screw into wall stud, drill holes at marked locations using 9/64” drill bit.

5.Re-place heater onto mounting bracket.

6.Place spacers between bottom mounting holes and wall anchor or drilled hole.

7.Hold spacer in place with one hand. With the other hand, insert mounting screw through bottom mounting hole and spacer. Place tip of screw in opening of wall anchor or drilled hole.

8.Tighten both screws until heater is firmly se- cured to wall. Do not over tighten.

Note: Do not re-place front panel at this time. Re- place front panel after making gas connections and checking for leaks.

FLOOR MOUNTING AWAY FROM WALL:

Figure 11

Installing Support Feet (see figure 11)

1.Lay heater onto table on its back with bottom edge overhanging table edge.

2.Securely attach feet to bottom of heater using 2 – self-tapping screws each.

Note: Feet should have long end going out the front of heater, and the edge coinciding with side of heater. If feet overhang side of the heater, switch leg location.

3.Place heater on non-combustible surface (see Locating Heater above) before proceeding with gas connection. If this will be a permanent loca- tion, heater may be locked into position using anchoring holes in mounting feet.

Note: Use of floor mounting feet will require you to use a 3/8 NPT street elbow to make gas connec- tion.

CONNECTING TO GAS SUPPLY

WARNING: A qualified service person must con-

nect heater to gas supply. Follow all local codes.­ WARNING: This appliance requires a 3/8” NPT

Unvented Liquid Propane Fired Room Heater

7

Installation Instructions and Owner’s Manual

Page 6 Page 8
Image 7
Page 6 Page 8
Contents HSIR30LPT HSIR20LPT HSIR10LP TSIR30LPT TSIR20LPT TSIR10LP Blue Flame Heaters­ Plaque Heaters­MHBF30LPT MHBF20LPT MHBF6LP HSBF30LPT HSBF20LPT TSBF30LPT TSBF20LPT HSBF10LP TSBF10LP MHIR30LPT MHIR20LPTCarbon Monoxide Poisoning PrecautionsPropane/LP Gas Ignition System Safety DeviceThermostatic Control on Thermostat Models Local CodesVentilation AIR Determining the Type of Heater Location SpaceVentilation from Inside Building Locating Heater Installation Check GAS TypeThis Installation Requires Ventilation from OutdoorsMounting Bracket Fastening Heater to WallPlacing Heater on Mounting Bracket Installing Bottom Mounting ScrewsInstalling Support Feet see figure Connecting to GAS SupplyTest Pressure Equal To or Less Than ½ psig 3.5 kPa Test pressure in Excess of ½ psig 3.5kPaWhat to do if YOU Smell GAS Pressure Testing Heater Gas ConnectionsElectrical Wiring Diagram Operating Your HeaterLighting Instructions Shutting OFF Heater To Turn OFF GAS to ApplianceBurner Flame Pattern Thermostat Control OperationInspecting Burner Pilot Flame PatternCleaning Heater Cabinet Cleaning and MaintenanceCleaning ODS/PILOT and Burner Cleaning Burner Pilot AIR Hole InletObserved SYMPTOM­ Possible CAUSE­ REMEDY­ TroubleshootingObserved SYMPTOM­ Possible CAUSE­ REMEDY­ Troubleshooting CON’TBF6LP BF10LP­ BF20LPT BF30LPT­ SpecificationsIR10 LP­ IR20LPT­ IR30LPT­Unvented Liquid Propane Fired Room Heater Unvented Liquid Propane Fired Room Heater Unvented Liquid Propane Fired Room Heater Unvented Liquid Propane Fired Room Heater Unvented Liquid Propane Fired Room Heater Technical Service REPLACEMENT­PARTSParts Under Warranty Parts not Under WarrantyUnvented Liquid Propane Fired Room Heater Model ­ Serial No. ­ Date Purchased ­ Warranty Information
Related manuals
Manual 24 pages 23.88 Kb

MHBF6LP, HSBF30LPT, HSIR20LPT, HSIR30LPT, HSBF20LPT specifications

The Enerco MHBF10LP, TSBF10LP, HSBF10LP, HSBF20LPT, and TSBF20LPT are innovative heating solutions designed for both commercial and residential applications. These units are highly efficient gas-fired heaters offering versatile heating capabilities, ensuring user comfort in various settings.

The MHBF10LP is a liquid propane heater featuring a powerful output of 10,000 BTU. It operates with a direct ignition system, allowing for quick and reliable startups. Its compact design makes it suitable for smaller spaces, while the adjustable heat settings empower users to customize their warmth. The MHBF10LP boasts a safety shut-off system which enhances the overall safety of the unit.

In contrast, the TSBF10LP is engineered for portability, offering the same 10,000 BTU output but with added mobility features. It comes with a built-in carrying handle and lightweight design, making it easy to transport from one location to another. Perfect for job sites or outdoor events, it features a sturdy construction that withstands demanding environments and a direct ignition system for ease of use.

The HSBF10LP, another variant in this range, offers high-efficiency heating in a small footprint. This model stands out with its integrated fan that aids in even heat distribution. Users can quickly warm up spaces without the long wait times. Additionally, it provides options for permanent installation, making it an adaptable choice for various applications.

The HSBF20LPT and TSBF20LPT models deliver enhanced power with a heating capacity of 20,000 BTU. The HSBF20LPT focuses on high efficiency and user convenience, featuring an automatic thermostat control to maintain desired temperatures without constant adjustment. Its robust design is perfect for larger areas, ensuring consistent warmth and comfort.

On the other hand, the TSBF20LPT is portable like its 10,000 BTU counterpart but with double the capacity. Its rugged construction and portability make it ideal for both indoor and outdoor use. The unit's reliability in diverse conditions is coupled with an ease of operation, providing warmth where it's most needed.

All models in this Enerco range prioritize user safety and efficiency. Featuring built-in safety mechanisms such as flame failure protection and tip-over shut-off systems, each heater ensures safe operation. Furthermore, the robust construction and high-quality materials used in these devices promise durability, making them a worthwhile investment for long-term heating needs.

Overall, Enerco's MHBF and TSBF series heaters represent a blend of modern technology, safety features, and user-friendly designs, tailored for a variety of heating applications.
Top Page Image Contents