State Industries Commercial Gas Water Heater instruction manual Venting, Wiring Diagram

Page 13

Installing the New Water Heater (cont’d)

5.The water heater must be electrically “grounded” by the installer. The unit will not operate unless it is prop- erly grounded. For complete grounding details and all allowable exceptions, refer to local codes or in the

absence of local codes, with the National Electrical Code, ANSI/NFPA 70 (latest edition).

6.Replace the wiring junction cover using the screws provided.

Wiring Diagram

NEUTRAL

HOT

 

 

ON/OFF SWITCH

 

 

HI LIMIT SWITCH

 

 

 

NO

 

 

PS

 

PRESSURE SWITCH

NC

 

 

 

 

C

 

 

ON/OFF

 

HOT

BLACK

 

WHC

 

 

N

NEUTRAL WHITE

 

IGNITOR

 

GROUND GREEN

 

L1

 

 

5

 

 

MAIN

CONTROL

N

I2

VALVE

 

L1

 

 

 

6

l1

 

 

 

7

1

 

3

 

 

 

 

5

 

 

6

BLOWER

 

7

CAUTION

Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper and danger- ous operation. Verify proper operation after servicing.

HI

LIMITBLOWER

YELLOW

BLUE

WHITE

BLACK

RED

BROWN

RED

WHITE

BLUE

BLUE

BLACK

YELLOW

 

IGNITOR

 

 

SENSOR

 

 

Venting

WARNING

To insure proper venting of this gas-fired water heater, the correct vent pipe diameter must be utilized. Any additions of other gas appliances on vent with this water heater will adversely affect the operation of the water heater.

WARNING

The vent outlet must connect to the water heater exhaust out- let. The vent inlet piping must connect to the water heater air inlet. Both the water heater connections are clearly marked. Failure to read this instruction can result in DEATH, SERIOUS BODILY INJURY, OR PROPERTY DAMAGE.

WARNING

The vent pipe from the water heater must be 3″ diameter vent pipe and must slope upward 1⁄8 inch per five linear feet.

All vent gases must be completely vented to the outdoors of the structure (dwelling).

MIN. RISE 1⁄8″

PER FIVE FEET

WARNING

Obstructed or deteriorated vent systems may present seri- ous health risk or asphyxiation.

WARNING

Failure to have required clearances between water heater and combustible material will result in a fire hazard.

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Used by this Water Heater For Your Safety AN Odorant is Added to the GASWhat to do if YOU Smell GAS Save this Manual for Future ReferenceDischarge Pipe General SafetyMust not be plugged or blocked DEATH, Serious Bodily INJURY, or Property Damage General Safety cont’dTable of Contents Introduction Preparing for the New InstallationTypical Installation Facts to Consider About the Location Locating the New Water HeaterILY INJURY, or Property Damage Facts to Consider About the Location cont’d Locating the New Water Heater cont’dCombustion Air and Exhaust Venting Through an Outside Wall ClearancesAir for Ventilation for Appliances Located Confined Spaces Wire FenceVenting Through Roof Clearances 18″Water Piping Installing the New Water HeaterTemperature-Pressure Relief Valve Installing the New Water Heater cont’dOptional Field Installed Wiring WiringFilling the Water Heater Venting Wiring DiagramVenting Through AN Outside Wall Venting cont’dVenting System Example Installations for ALL Models Installing the New Water Heater contdVent piping can be installed as follows Minimum vent length for all models is 18 inchesCementing PVC, ABS or Cpvc Pipe and Fittings PrecautionsVent Pipe Separation Typical installation Connecting Vent to BlowerVenting contd Venting Through a RoofVenting Through a Roof CONT’D Gas PipingGAS Piping with ALL Black Iron Pipe to GAS Control GAS Piping with Flexible ConnectorSediment Trap Before Operating the Water Heater Installation ChecklistIts hookup? Model Rating PlateBefore the Water Heater will Operate OperatingOperation Check for Leaks Operating cont’dFor Your Safety Read Before Operating Temperature Regulation Start Up Conditions For Your InformationOperational Conditions Operational Conditions cont’d For Your Information cont’dBurner Cleaning Periodic MaintenanceVenting System Inspection Burner InspectionPeriodic Maintenance cont’d Leakage Checkpoints Thermostat and GAS Supply Check TroubleshootingDiagram for Electrical System Check on pages 32 Troubleshooting cont’dElectrical System Check Use diagram onFrom facing TWO Temp Water Heater Installation Installation DiagramsCirculating Tank System GAS/WITH Single Storage System GAS/INSTANTANEOUS or StorageWater Heater Installation GAS/INSTANTANEOUS Installation Diagrams contdPrimary Plus Booster Water Heater Installation Or StorageModel Repair PartsThis is a Repair Parts LIST, not a Packing List Repair Parts cont’dPart Description Part Number Page

Commercial Gas Water Heater specifications

State Industries has carved a niche for itself as a leader in the water heating industry, providing reliable solutions for various commercial applications. One of the standout products in their lineup is the State Industries Commercial Gas Water Heater. This powerhouse is designed to meet the demanding hot water needs of businesses, from restaurants and hotels to schools and hospitals.

One of the primary features of the State Commercial Gas Water Heater is its high efficiency. These units are engineered to deliver optimal performance while reducing energy costs. With innovative technologies such as a power vent system and advanced burner design, they maximize heat transfer and minimize heat loss. This efficiency not only translates to lower operating costs but also a reduced environmental impact, making it a smart choice for businesses looking to operate sustainably.

Durability is another hallmark of State Industries' gas water heaters. Constructed from robust materials, these units are designed to withstand the rigors of daily use in a commercial environment. The tanks are often lined with glass and reinforced to prevent corrosion, enhancing the longevity of the unit. Additionally, the use of high-quality components ensures minimal maintenance and reliable operation over time, allowing businesses to focus on their core activities rather than downtime due to equipment failure.

State's Commercial Gas Water Heaters also come equipped with advanced safety features. This includes built-in temperature controls, pressure relief valves, and flame failure protection, which work together to ensure safe operation even in high-demand situations. These features provide peace of mind to operators and help meet stringent safety standards, making them suitable for any commercial setting.

Furthermore, the versatility of these water heaters is remarkable. They are available in various sizes and configurations, allowing businesses to choose a model that perfectly fits their water heating requirements. Whether for high-volume hot water needs or continuous flow applications, State's Commercial Gas Water Heaters are designed to adapt.

In conclusion, the State Industries Commercial Gas Water Heater stands out as a top choice for businesses needing reliable and efficient hot water solutions. With its focus on efficiency, durability, safety, and versatility, this water heater is built to meet the rigorous demands of the commercial market while providing value and peace of mind to operators.
Top Page Image Contents