State Industries Commercial Gas Water Heater instruction manual Typical Installation

Page 6

Typical Installation

INTAKE FOR

COMBUSTION

EXHAUST AIR

VENT TO

OUTDOORS

FLUE PRODUCTS

DISCHARGE PIPE

HOT WATER OUTLET

TEMPERED

WATER OUTLET

MIXING

VALVE

GAS

SUPPLY

7' POWER CORD (Factory supplied)

Vacuum Relief required by some codes

(refer to local codes)

AIR INTAKE PIPE

COLD WATER INLET

SHUTOFF VALVE

TEMPERATURE-

PRESSURE RELIEF

VALVE

DISCHARGE PIPE (Do not cap or plug)

PROVIDE A 6″ AIR GAP

BETWEEN THE END OF

THE DISCHARGE PIPE

AND DRAIN

This appliance has been design certified as complying with American National Standard/CSA Standard for water heaters and is con- sidered suitable for:

Water (Potable) Heating: All models are “considered suitable for water (potable) heating.”

Water (Potable) Heating and Space Heating: Certain models are “considered suitable for water (potable) heating and space heating.” Refer to the model and rating plate of the water heater.

WARNING

If this water heater is to be used for multiple location users, such as for apartments, hotels, motel, duplexes, a tempering device should be used at each point of use (sink, shower, tub, etc.) to limit the maximum temperature of the hot water to 125°F. This will help to reduce, but not eliminate the risk of scald or serious burn injury form exposure to hot water. Water at a temperature above 125°F, can cause 3rd degree burn injuries which are the most serious burns and require skin grafts and results in permanent scarring or even death. Some people are more likely to be permanently injured by hot water than others; these include the elderly, children, the infirm, or the physically/mentally handi- capped. Before immersing yourself or anyone else in hot water, be sure to check the water temperature. WARNING: HOTTER WATER INCREASES THE RISK OF SCALD INJURY. (Also see “Temperature Regulation” section) Mixing valves are available at plumbing supply or hardware stores. Follow manufacturer’s instructions for installation of these valves.

WARNING

This water heater shall not be connected to any heating systems or component(s) previously used with a non- potable water heating appliance.

If this water heater is also used for space heating applica- tions, all piping and components connected to the water heater shall be suitable for use with potable water.

WARNING

Toxic chemicals such as used for treatment of boilers or non-potable water heating appliances shall never be intro- duced into a potable water space heating system.

NOTE: To protect against untimely corrosion of hot and cold water fittings, it is strongly recommended that di-electric unions or couplings be installed on this water heater when connected to copper pipe.

6

Page 5 Page 7
Image 6
Page 5 Page 7
Contents What to do if YOU Smell GAS For Your Safety AN Odorant is Added to the GASUsed by this Water Heater Save this Manual for Future ReferenceGeneral Safety Discharge PipeMust not be plugged or blocked General Safety cont’d DEATH, Serious Bodily INJURY, or Property DamageTable of Contents Preparing for the New Installation IntroductionTypical Installation Locating the New Water Heater Facts to Consider About the LocationILY INJURY, or Property Damage Combustion Air and Exhaust Locating the New Water Heater cont’dFacts to Consider About the Location cont’d Venting Through an Outside Wall ClearancesVenting Through Roof Clearances Wire FenceAir for Ventilation for Appliances Located Confined Spaces 18″Installing the New Water Heater Water PipingInstalling the New Water Heater cont’d Temperature-Pressure Relief ValveWiring Optional Field Installed WiringFilling the Water Heater Wiring Diagram VentingVenting cont’d Venting Through AN Outside WallVent piping can be installed as follows Installing the New Water Heater contdVenting System Example Installations for ALL Models Minimum vent length for all models is 18 inchesPrecautions Cementing PVC, ABS or Cpvc Pipe and FittingsVent Pipe Separation Venting contd Connecting Vent to BlowerTypical installation Venting Through a RoofGas Piping Venting Through a Roof CONT’DGAS Piping with Flexible Connector GAS Piping with ALL Black Iron Pipe to GAS ControlSediment Trap Its hookup? Installation ChecklistBefore Operating the Water Heater Model Rating PlateOperating Before the Water Heater will OperateOperation Operating cont’d Check for LeaksFor Your Safety Read Before Operating Temperature Regulation For Your Information Start Up ConditionsOperational Conditions For Your Information cont’d Operational Conditions cont’dVenting System Inspection Periodic MaintenanceBurner Cleaning Burner InspectionPeriodic Maintenance cont’d Leakage Checkpoints Troubleshooting Thermostat and GAS Supply CheckTroubleshooting cont’d Diagram for Electrical System Check on pages 32Use diagram on Electrical System CheckFrom facing Circulating Tank System GAS/WITH Single Storage System Installation DiagramsTWO Temp Water Heater Installation GAS/INSTANTANEOUS or StoragePrimary Plus Booster Water Heater Installation Installation Diagrams contdWater Heater Installation GAS/INSTANTANEOUS Or StorageRepair Parts ModelRepair Parts cont’d This is a Repair Parts LIST, not a Packing ListPart Description Part Number Page

Commercial Gas Water Heater specifications

State Industries has carved a niche for itself as a leader in the water heating industry, providing reliable solutions for various commercial applications. One of the standout products in their lineup is the State Industries Commercial Gas Water Heater. This powerhouse is designed to meet the demanding hot water needs of businesses, from restaurants and hotels to schools and hospitals.

One of the primary features of the State Commercial Gas Water Heater is its high efficiency. These units are engineered to deliver optimal performance while reducing energy costs. With innovative technologies such as a power vent system and advanced burner design, they maximize heat transfer and minimize heat loss. This efficiency not only translates to lower operating costs but also a reduced environmental impact, making it a smart choice for businesses looking to operate sustainably.

Durability is another hallmark of State Industries' gas water heaters. Constructed from robust materials, these units are designed to withstand the rigors of daily use in a commercial environment. The tanks are often lined with glass and reinforced to prevent corrosion, enhancing the longevity of the unit. Additionally, the use of high-quality components ensures minimal maintenance and reliable operation over time, allowing businesses to focus on their core activities rather than downtime due to equipment failure.

State's Commercial Gas Water Heaters also come equipped with advanced safety features. This includes built-in temperature controls, pressure relief valves, and flame failure protection, which work together to ensure safe operation even in high-demand situations. These features provide peace of mind to operators and help meet stringent safety standards, making them suitable for any commercial setting.

Furthermore, the versatility of these water heaters is remarkable. They are available in various sizes and configurations, allowing businesses to choose a model that perfectly fits their water heating requirements. Whether for high-volume hot water needs or continuous flow applications, State's Commercial Gas Water Heaters are designed to adapt.

In conclusion, the State Industries Commercial Gas Water Heater stands out as a top choice for businesses needing reliable and efficient hot water solutions. With its focus on efficiency, durability, safety, and versatility, this water heater is built to meet the rigorous demands of the commercial market while providing value and peace of mind to operators.
Top Page Image Contents