Whirlpool T-K1S Exhaust Venting, Indoor Clearances, Manufactured Home Mobile Home Installation

Page 12

Exhaust Venting

This water heater must be vented in accordance with the section on venting of equipment in the latest edition of the National Fuel Gas Code.

This is a Category III appliance, and must be vented accordingly. The following are UL listed manufacturers: ProTech Systems FasNSeal, Z- Flex Inc. Z-Vent II and Heat-Fab Inc. Saf-T Vent. This unit requires 4” vent pipe. Connect the vent pipe to the unit so that it is sealed airtight. Follow the vent pipe manufacturer’s instructions when installing the vent pipe. Do not common vent this appliance with any other vented appliance.

The venting system must not exceed a length of 35 ft. minus 5 ft. for every elbow. Do not use more than 3 elbows.

No. of Elbows

Max. Vertical or

 

Horizontal Length

0

35 ft.

1

30 ft.

2

25 ft.

3

20 ft.

If the horizontal vent run exceeds 5 ft., the following criteria must be observed:

There must be a 2 ft. vertical run off the top of the heater before the horizontal run begins.

The horizontal run must be supported at 3’ intervals.

The vent run should be pitched up towards the termination at ¼” per foot.

The unit can be vented either up and out the roof, or directly through a wall. If the unit will be vented through a wall, use Takagi USA Inc. optional part, the TK-TV01 vent terminator, or an equal Category

IIIvent part. Locate the vent terminator according to ANSI Z223.1/NFPA 54 and applicable local codes.

Maintain the following clearances to any combustible surface in an indoor installation:

Indoor Clearances

Piping side

6”

Front (Maintenance

Suggested 24”

space)

Min. 4”

Floor

Noncombustible base

Back of heater

1”

Non piping side

2”

Top of heater

12”

Manufactured Home (Mobile Home) Installation

This appliance must be installed in accordance with the Manufactured Home Construction and Safety Standard, (Title 24, CFR; Part 3280) and ANSI A119.5/NFPA 501D. In addition, install in accordance with the following instructions, the instructions supplied with any venting, local codes, utility company requirements for the installation of water heaters in manufactured homes (mobile homes), and the latest edition of the National Fuel Gas Code, ANSI Z221.3/NFPA 50.

Locate the heater in an enclosure separating the unit from the internal atmosphere of the manufactured home or trailer. All combustion air must be obtained from the outside atmosphere, and the flue gases must be discharged directly outdoors through a gas vent. There must be no opening from the interior of the home or trailer into the water heater enclosure.

Indoor Installation

Follow indoor installation instructions as set out in an earlier section of this manual, except that combustion air must not be taken from the inside of the home or trailer.

Outdoor Installation

Follow outdoor installation instructions as set out in an earlier section of this manual.

If the unit is to be installed in a recessed area, connect a gas vent to the unit, which will direct exhaust gases out of the recessed area.

Indoors

Outdoors

Min. 3"

Min. 32"

Min. 3"

11

Image 12
Contents K1SInstantaneous Water Heater Flash Water Heater Model T-K1STable of Contents SpecificationsFor Your Safety Temperature Operation GeneralTurning It On Turning It OffFreeze Prevention Installation Electrical ConnectionsWiring Diagram Gas Supply Piping Natural Gas Supply PipingPropane Supply Piping Water Plumbing Pressure Relief ValveWall Hanging Installation Standing InstallationOutdoor Installation Indoor Installation Combustible Air SupplyManufactured Home Mobile Home Installation Indoor InstallationOutdoor Installation Exhaust VentingInitiating the Appliance Initial OperationSpace Heating Application Dual-purpose hot water heating Domestic and Space Heating Applications K1S with Storage TankRecirculation For Your Safety Read Before Operating Page Troubleshooting MaintenanceWater Isn’t Hot Enough It Takes Too Long to Get Hot WaterError Codes Computer BoardTKRE01emperature Remote Controller TK-TV03 Vent Damper Optional ItemsCase Heat Exchanger Manifold Burner Computer K1S Parts List Page 254

T-K1S specifications

The Whirlpool T-K1S is a cutting-edge tankless water heater designed to provide endless hot water while maximizing energy efficiency. This model is part of Whirlpool's commitment to innovative technology and superior performance, making it a popular choice for both residential and commercial applications.

One of the standout features of the T-K1S is its on-demand heating capability. Unlike traditional water heaters that store hot water in a tank, the T-K1S heats water only when needed. This eliminates the need for a storage tank and reduces the risk of running out of hot water during peak usage times. Homeowners can enjoy continuous hot water, making it ideal for multiple simultaneous uses such as showers, dishwashing, and laundry.

The T-K1S is equipped with advanced technology that optimizes energy use. With its high-efficiency rating, it significantly reduces energy consumption compared to conventional water heaters. The built-in digital scale allows users to set precise temperatures, ensuring comfort while also promoting energy conservation. This feature also helps to minimize the carbon footprint, making the appliance an eco-friendly option.

Safety is a paramount consideration in the design of the T-K1S. It features multiple safety mechanisms, including a robust thermal control system that prevents overheating. The unit also has a built-in safety shut-off mechanism which activates in the event of water flow disruptions, ensuring peace of mind for users.

Another noteworthy characteristic of the T-K1S is its compact design. The space-saving design offers flexibility in installation, allowing it to fit in small or tight spaces, such as utility rooms, basements, or even closets. This feature is especially beneficial for those with limited room for traditional, bulky water heating systems.

Durability is another key aspect of the Whirlpool T-K1S. Constructed with high-quality materials, it is designed to withstand the test of time, minimizing the need for repairs or replacements. Whirlpool also offers excellent warranty options for added security on your investment.

In summary, the Whirlpool T-K1S is an exceptional tankless water heater that combines efficiency, safety, and durability. With its on-demand heating technology, energy-saving features, and compact design, it represents a smart choice for anyone looking to enhance their hot water supply while being environmentally conscious. It embodies Whirlpool's commitment to quality and performance, making it a leading option in the market.