Whirlpool CA15WYR0 manual Install SMART-MOUNTTray Assembly in Window

Page 7

2.Insert carriage bolt up through slot on tray-frame side and support leg.

3.Place one end of tray center over carriage bolt.

4.Then place flat washer, lock washer and hex nut.

NOTE: Do not tighten. The leg must be able to move freely to adjust angle when installed.

A

B

C

D

 

E

A. Hex nut

D. Tray center

B. Lock washer

E. Carriage bolt

C. Flat washer

 

5.Insert second carriage bolt through tray side and attach other end of support leg.

NOTE: Do not tighten. The leg must be able to move freely to adjust angle when installed.

A

B

C

D

A. Hex nut

C. Flat washer

B. Lock washer

D. Carriage bolt

6.Install support leg on other side.

Install SMART-MOUNT®Tray Assembly in Window

1.From inside, place SMART-MOUNT®tray, support legs facing down, in the window. Match the holes in tray side with the predrilled holes in windowsill.

2.Using 2 - #10 - 12 x 1¹⁄₂" slot-head wood screws, secure the tray frame to the window.

A

A. #10 - 12 x 1¹⁄₂" slot-head wood screws

NOTE: If the exterior of building can be damaged by support legs, place a board between the wall and support legs.

3.With tray center pushed away from the windowsill, place a level on the angled edge on top of the tray side. Be sure level is against notch on tray side.

A B

A. Angled edge on top of the tray side

B.Notch

4.Adjust SMART-MOUNT®tray until bubble indicates the angled edge on top of the tray side is level.

IMPORTANT: The tray must slope downward slightly toward the outside to provide proper drainage for the air conditioner.

A

B

A. Bubble indicates the angled edge on top of the tray side is level. B. Place level on angled edge against notch on tray side.

5.Tighten the hex nut just enough to hold tray center in place.

6.Repeat with other side.

7.Tighten hex nuts securely with ⁷⁄₁₆" wrench.

7

Image 7
Contents 1188226B AIR ConditionerAIR Conditioner Safety Table of ContentsTools and Parts Installation RequirementsLocation Requirements Electrical Requirements Window InstallationRecommended grounding method Remove packaging materials Power Supply CordTo test your power supply cord Unpack the Air ConditionerAssemble SMART-MOUNTTray Window InstallationAttach Support Legs Thin Wall Construction vinyl, wood, etcInstall SMART-MOUNTTray Assembly in Window Top View Install Side Curtains Prepare Air Conditioner for Window InstallationTop View Bottom View Side View Attach Side Curtains to Window Correct InstallationIncorrect Installation Position the Air Conditioner in WindowOption 1-Wood, Metal or Plastic Molding Through-the-Wall InstallationComplete Installation Top ViewInstall Wood Frame Install SMART-MOUNTTray Assembly in Wall Opening Left Side Position the Air Conditioner Through the WallRight Side Top of wall opening Top channel Air conditioner Mode AIR Conditioner USEStarting Your Air Conditioner-Digital Control Fan SpeedTo clear Timer delay program TemperatureTo change the temperature display from F to C Timer DelayTo raise the temperature To select the modeTo lower the temperature Models With Power Saver Models Without Power Saver Exhaust Control on some modelsStarting Your Air Conditioner-Rotary Control Normal Sounds Changing Air DirectionAnnual Maintenance Cleaning the Air FilterCleaning the Front Panel Repairing Paint DamageAir conditioner seems to run too much TroubleshootingAir conditioner cycles on and off too much or does not cool Temperature on display does not match room temperatureWater drips from cabinet into your house Accessories Assistance or ServiceU.S.A 1188226B