Allied International Home Security System manual Camera I/O pin assignment 8 pin Guppy

Page 40

Camera interfaces

Camera I/O pin assignment (8 pin) (GUPPY)

The 8-pin camera I/O connector (only Guppy cameras) is designed for indus- trial use.

It provides:

•access to the inputs and outputs on the camera

•a serial interface

Note	The part number of the appropriate straight I/O connector is:

•HIROSE HR25-7TP-8S, AVT article number K7600503

AVT also supplies various I/O cables of different lengths, a selection is listed below:

I/O cable, open 8-pin HIROSE female to open end, 2.0 m	E1000842
I/O cable, open 8-pin HIROSE female to open end, 5 m	E1000843

The following diagram shows the pinning of the I/O connec- tors as viewed in pin direction.

7 4

8 6 3 1

5 2

Pin	Signal	Direction	Level	Description

1	CameraOut1	Out	TTL	Camera Output 1

2	CameraOut2	Out	TTL	Camera Output 2

3	CameraOut3	Out	TTL	Camera Output 3

4	CameraIn	In	TTL	Camera Input

5	RxD_RS232	In	RS232	Terminal Receive Data

6	TxD_RS232	Out	RS232	Terminal Transmit Data

7	ExtPower		+8…36V	Power Supply

8	GND		GND	Ground

Figure 16: Camera I/O connector pin assignment (GUPPY)

Hardware Installation Guide V2.0.0

40

Image 40

Contents Hardware Installation Guide AVT CamerasLegal notice Allied Vision Technologies GmbH 03/2008Contents Control and video data signals Camera interfaces Ieee 1394a port pin assignmentContacting Allied Vision Technologies Info Technical informationOrdering and commercial information AVT Modular Camera ConceptDocument history IntroductionManual overview Conventions used in this manual StylesRead all notes and cautions carefully Style Function ExampleSymbols AVT accessoriesMore information Existing applicationsWww For more information on accessories go to AVT softwarePackages WwwAVT Technical Manuals Www For downloading the Technical Manuals go toSafety instructions General safety instructionsFireWire safety instructions Changing filters safety instructionsFireWire hot-plug and screw-lock precautions Screw-lock precautionsGuppy changing filters safety instructions PIKE/OSCAR changing filters safety instructionsMarlin changing filters safety instructions PIKE/STINGRAY voltages PIKE/STINGRAY GOF connectorsGuppy voltages MARLIN/OSCAR voltages Dolphin voltagesSafety instructions Ited warranty or cancelation of warranty Safety instructions for board level camerasTions before use Always use clean boards Board level cameras General WarningsBoard level cameras Loading Board level cameras Dirty environmentsAVT camera cleaning instructions WarrantyWarranty precautions General warningsAvoiding the necessity of camera cleaning Where is the impurity? Locating impurities Is it an impurity? Identifying impuritiesCamera type Tool to be used Description Cleaning Instructions Medical-grade sterile optical cottonScratches Are not free from contaminationIar with cleaning a camera with this instrument AVT dealerAVT cameras installing hardware AVT SoftwarePackagesHardware conditions 1394b for different requirementsFireWire cable Description K1200165Marlin / Oscar / Guppy K1200162Overview hardware installation Installing Ieee 1394 adapterConnecting camera to PC or laptop Hot-plug precautionsDo not touch the shield of the camera cable con CameraIeee 1394b connector copper Pin camera Connector Status LEDsCamera interfaces Hirose and 1x 1394a Hirose and 2x 1394b Hirose and 1x 1394aRear view of AVT cameras Hirose and 1394 copper Pike fiber Stingray fiber Pin Signal Cable powerIeee 1394a port pin assignment Cable GNDBoard level camera Ieee 1394a port pin assignment Signal PinCable shield VP Power, VCC Ieee 1394b port pin assignment PIKE, StingrayMakes it possible to control the camera and output Second cameraPower PIKE/STINGRAY fiber infos and cautionsGOF transmission uses MMF multi-mode fiber at 850 nm Optical connection okPlug clean On the GOF connectorSion Please note that optical fiber cables have aPin Signal Direction Level Description Camera I/O pin assignment 8 pin GuppyBoard level camera Guppy I/O pin assignment Camera I/O connector pin assignment 12 pin Order text Order numberK7600040 As shown belowPin Signal Use Dolphin familyOscar and Marlin family GPOutput Open emitterPike and Stingray family Level DescriptionControl and video data signals Technical ManualsInputs DOLPHIN, OSCAR, MARLIN, GUPPY, PIKE, Stingray Guppy outputs are not short-circuit-proofInput schematics Pike Flux voltage from LED type 1.2 V at 20 mAInput characteristics Flux voltage OSCAR, MARLIN, Pike Cycle delay of the optical couplerFlux voltage from LED type 1.5 V at 10 mA Recommended Description Ratings Operating conditionsGuppy The inputs can be connected directly to +5 ALL Cameras The following note is valid for all cameras Voltages above +30 V may damage the optical couplerRegisters see the Technical Manuals Input Ground InGND Pin no from camera I/O connector Pike Input Ground InGND Pin no from camera I/O connector StingrayParameter Test condition Value Outputs DolphinOutVCC Resistor value See Output schematics with external resistor R Dolphin on Configuration via registers see Technical ManualsOutputs OSCAR/MARLIN Emitter current Max mA Emitter collector voltageOutputs Guppy Outputs Operating conditionsOutputs Pike Output parameters PikeVoltage above +45 V may damage the optical coupler Sym Value Condition Bol00 µs Rise time 60 µs Storage 48.00 µsOutputs Stingray Output parameters Stingray≈ 5 mA load Voltage above +30 V may damage the optical coupler78 µs Rise time 65 µs Storage 27.6 µsFirmware update Contact your local dealerIndex Operating Operating systemOptical coupler 40, 42