Bosch Appliances LTC 8540/00 Allegiant CPU Bay Connections, Operational Settings, Desk Top Mount

Page 8

LTC 8540/00 Series Instruction Manual Installation

4.2.2 Desk Top Mount

If the unit is not going to be rack mounted, the enclosure’s mounting ears should be removed. The cover of the unit must be removed before access to the mounting ears is possible. Removal of the cover should only be performed by qualified service personnel. The unit should always be disconnected from the Allegiant CPU bay (or alternate power source if one is being used) before removing the cover.

The top cover is fastened to the case by 4 screws located on the rear of the unit. Once the screws have been removed, the cover slides back and off the unit. Remove each mounting ear by removing the screw holding the mounting ear to the enclosure chassis. Refer to the drawing below if needed.

S929A39AE

Cover and Rack Ears Removal

4.3Allegiant CPU Bay Connections

With the power turned “OFF” on the Allegiant series main CPU bay, install the alarm interface unit in the rack close enough to the location of the main CPU bay to allow the supplied cable to be used.

Connect one end of the supplied 9-pin D-type cable labeled “ALARM” to the rear of the unit and the other end to the Allegiant main CPU bay connector marked “ALARM”. Remember to tighten both connector attachment screws at each connection point. The front panel LED should light upon application of power to the main CPU bay.

EN 8

4.4Operational Settings

The unit contains internal DIP switches which can be used to set certain operating characteristics. The lid to the unit must be removed as described above if the DIP switches need to be changed from their Factory default settings. Refer to the LTC 8540/00 table below for DIP locations. The following tables summarize the DIP switch settings and their associated features:

LTC 8540/00

S103 - DIP

Function

Switch No.

 

1

ON for alarms 1 to 32 as normally open (NO).1

 

OFF for alarms 1 to 32 as normally closed (NC).

2

ON for alarms 33 to 64 as normally open (NO).1

 

OFF for alarms 33 to 64 as normally closed (NC).

3

ON for alarm output relays as normally open (NO).1

 

OFF for alarm output relays as normally closed

 

(NC).

4

ON for audible buzzer enabled.1

 

OFF to disable audible buzzer.

 

 

 

 

S101 - DIP

 

Switch No.

Function

4

ON for RTS/CTS enabled.

 

OFF to disable RTS/CTS.1

 

 

1Denotes Factory default settings.

The unit communicates with the Allegiant main CPU bay using RS-232. The first three switches of DIP switch S101 are used to select the desired baud rate. Refer to the LTC 8540/00 layout diagram below for locations. Follow the table if a change from the Factory default setting is required.

Note that the Allegiant CPU bay must also be set to the same baud rate.

LTC 8540/00

S101 - DIP Switch No.

 

Baud

1

2

3

Rate

OFF

OFF

OFF

192001

OFF

OFF

ON

9600

OFF

ON

OFF

4800

OFF

ON

ON

2400

ON

OFF

OFF

12002

ON

OFF

ON

600

ON

ON

OFF

Not Used

ON

ON

ON

Not Used

 

 

 

 

1Denotes Factory default settings on units starting with serial No. 1500.

2Denotes Factory default settings on units below serial No. 1500.

Bosch Security Systems December 13, 2007

Page 7 Page 9
Image 8
Page 7 Page 9
Contents LTC 8540/00 Series Bosch Security Systems December 13 Important Safeguards For Rack-mount Product For Indoor ProductFor Outdoor Product FCC & Ices Information Table of Contents Service InstallationUnpacking DescriptionOperational Settings Allegiant CPU Bay ConnectionsDesk Top Mount Cover and Rack Ears RemovalAlarm Input Connections Alarm Output ConnectionsInterface Port Pinouts LTC 8540/00 Alarm Interface Unit Layout IllustrationsConsignes de Sécurité Importantes Sécurité Modèle Destiné Aux Applications DintérieurModèle Destiné Aux Applications Dextérieur Modèle Destiné Au Montage En BâtiInformations FCC ET Ices Sommaire Alimentation/Données DeballageCentres d’entretien Options de montage Connexions de la baie du processeur central AllegiantRéglages opérationnels Retrait du couvercle et des pattes pour châssisConnexions d’entrée d’alarme Connexions de sortie d’alarmeBrochage du port d’interface Panneaux avant et arrière du module LTC 8540/00 LTC 8540/00 Série Instructions d’installation Wichtige Sicherheitshinweise Sicherheitshinweise Geräte Für Den InneneinsatzGeräte Für Den Ausseneinsatz Geräte Für Die Rack-MontageInhaltsverzeichnis Auspacken KundendienstBeschreibung KundendienstzentrenEinbauoptionen Anschluß an das Allegiant-CPU HauptgerätBetriebseinstellungen GestelleinbauAlarmeingangsanschlüsse AlarmausgangsanschlüssePinbelegung des Schnittstellenports Anordnung der LTC 8540/00 Alarmschnittstelleneinheit Typische Anwendung der LTC 8540/00 AlarmschnittstelleAbbildungen LTC 8540/00 Vorder- und RückseiteMedidas Importantes Precauciones de Seguridad Para Productos Instalados En El InteriorPara Productos Instalados En El Exterior Para Productos De Montaje En SoporteÍndice Desembalaje Servicio Descripción InstalaciónDesembalaje ServicioDescripción InstalaciónOpciones de montaje Ajustes de funcionamientoMontaje de estantería Montaje sobre mesaConexiones de entrada de alarma Conexiones de salida de alarmaPatillas Funciones Tierra de la caja Recepción Transmisión Configuración de unidad de interfaz de alarma LTC 8540/00 Aplicación de interfaz de alarma de LTC 8540/00 típicaIlustraciones Panel delantero y posterior de la LTC 8540/00Belangrijke Veiligheidsvoorschriften Veiligheidsmaatregelen Voor Producten Die Binnenshuis Worden GebruiktVoor Producten Die Buitenshuis Worden Gebruikt Voor Producten Die In Een Rek Worden GemonteerdInhoudsopgave Installatie ServicecentraUitpakken BeschrijvingOperationele instellingen Allegiant CPU bay-verbindingenMontage op bureau Verwijderen deksel en rek-ogenAlarm inputverbindingen Alarm outputverbindingenInterface poort pinouts LTC 8540/00 Layout alarm interface unit Typische LTC 8540/00 alarm interface toepassingIllustraties LTC 8540/00 Voor- en achterpaneelPrecauzioni importanti Sicurezza Prodotto Per InterniProdotto Per Esterni Prodotto Per Montaggio In RackIndice Installazione DisimballoAssistenza DescrizioneConfigurazione operativa Opzioni di montaggioCollegamenti della CPU Allegiant Rimozione del coperchio e delle alette del rackCollegamenti d’ingresso degli Allarmi Collegamenti d’uscita degli allarmiPiedini Funzione Terra telaio Ricezione Trasmissione Illustrazioni Disposizione dell’interfaccia allarmi LTC 8540/00Applicazione tipica dell’interfaccia allarmi LTC 8540/00 Pannello anteriore e posteriore LTC 8540/00Serie LTC 8540/00 Istruzioni per l’installazione Serie LTC 8540/00 Istruzioni per l’installazione

LTC 8540/00 specifications

The Bosch LTC 8540/00 is an advanced kitchen appliance designed to enhance the cooking experience with its innovative features and technologies. This high-performance oven is a blend of cutting-edge engineering and user-friendly functionalities, making it an ideal choice for both novice cooks and seasoned chefs.

One of the standout features of the Bosch LTC 8540/00 is its intuitive control panel. Equipped with a touch display, it allows users to easily navigate through various cooking modes, temperature settings, and timer functions. The clear interface ensures that even the most complex cooking tasks can be accomplished with ease, reducing the learning curve for new users.

This model boasts a multifunctional cooking system, incorporating several cooking modes such as convection baking, grilling, and baking. The convection baking mode circulates hot air, ensuring even cooking and browning. The grilling function is perfect for achieving a perfectly charred finish on meats and vegetables, while the dedicated baking mode provides optimal heat distribution for baked goods.

In terms of technology, the Bosch LTC 8540/00 showcases the brand’s commitment to energy efficiency. It operates with reduced energy consumption, helping users save on utility bills while also being environmentally friendly. Additionally, its rapid preheat function ensures that the oven reaches the desired temperature in a fraction of the time compared to traditional ovens, enhancing overall cooking efficiency.

Another notable characteristic is the built-in self-cleaning feature. This innovative technology utilizes high temperatures to incinerate food residues, eliminating the need for harsh chemicals and manual scrubbing. This not only saves time but also contributes to a cleaner kitchen environment.

The oven's spacious interior can accommodate large dishes and multiple trays, making it ideal for family gatherings and dinner parties. The sleek design and stainless-steel finish add a modern touch to any kitchen decor, blending seamlessly with surrounding appliances.

Overall, the Bosch LTC 8540/00 stands out for its combination of advanced features, user-friendly design, and efficient cooking technologies. It represents a perfect blend of functionality and aesthetics, tailored to meet the demands of contemporary cooking. Whether baking, roasting, or grilling, it promises to deliver consistent and delicious results every time.
Top Page Image Contents