Bosch Appliances DS7445I Phone Number General Control Programming, Phone Answering Programming

•Low Battery: This report is sent when a low battery condition occurs.

•Battery Restoral: This report is sent when a low battery condition restores.

•AC Fail: This report is sent when an AC failure condition occurs. This report may be delayed in address 4034.

•A/C Failure Report Delay

The A/C power loss report can be programmed to delay for up to 254 minutes (see address 4034). (The same delay would also apply to the A/C restoral report.)

-If another report is sent during this delay period, the A/C fail report will be sent along with this report.

-If the A/C power restores during this delay period, the A/C loss report will not be sent.

-Programming address 4034 as FF causes the report to be sent at a random interval of at least 15 minutes, but no more than 2 hours after the A/C failure occurs.

•AC Restoral: This report is sent when an AC failure condition restores.

•Communicator Test/System Normal: This report is sent at the 24-hourcheck-in time if there is not a control trouble, an active fire alarm that has not been acknowledged, a fire trouble, or a supervisory condition. Note: To send a Communicator Test even if one of these conditions exists, program the Communicator Test/System Off Normal.

•Remote Program Successful: This report is sent after a Remote Program session, if the session was terminated properly.

•Remote Program Unsuccessful: This report is sent after a Remote Program session, if some error has occurred or the session did not terminate properly.

•Local Program Successful: This report is sent when local programmer’s mode is exited and there is no error associated with the programming.

•Local Program Unsuccessful: This report is sent when local programmer’s mode is exited and there has been some error associated with the programming.

•System Trouble: This report is sent when a control trouble condition occurs.

•System Trouble Restoral: This report is sent when all system trouble conditions restore.

•Communicator Test/System Off Normal: This report is sent at the 24-hourcheck-in time if there is a control trouble, an active fire alarm that has not been acknowledged, a fire trouble, or a supervisory condition.

•Exit Error: This report is sent if an exit error occurs. An exit error occurs when an entry/exit zone is still violated at the end of the exit delay. If this happens, the entry delay will begin and any output programmed to activate an alarm will energize. If the system is not disarmed before the entry delay expires, an alarm report for the effected zone will be sent and the Exit Error report will be sent. If this report is not programmed, the control will not sound the exit error warning.

•Recent Closing: This report is sent, along with any alarm reports, when there is an alarm within the first five minutes after the system has been armed.

•System Walk Test: This report is sent when a system test has been started ([#] [8] [1] key sequence). Zone reports are sent during a system test.

•System Walk Test Restoral: This report is sent when the system test has been completed or has timed-out.

•Fire Walk Test: This report is sent when a Fire Walk Test has been started ([#] [9] [1] key sequence). Zone reports are not sent during a Fire Walk Test.

•Fire Walk Test Restoral: This report is sent when the Fire Walk Test has been completed or has timed-out.

•Mux. Smoke Low Temperature Report: This supervisory report is sent when a MX280 Series smoke detector with a low temperature feature detects a temperature of 45°F (7.5°C) or less for a period of 30 minutes or more.

•Mux. Smoke Low Temperature Restoral: This report is sent when a MX280 Series smoke detector with a low temperature alarm determines that the temperature has risen above 45°F (7.5°C).

•Dirty Chamber Report: This report is sent when a MX280 Series smoke detector fails to pass the “Chamber Check®” sensitivity test.

•Dirty Chamber Restoral: This report is sent when a MX280 Series smoke detector has been returned to normal operation after service.

6.14Phone Number General Control Programming

•Enable Remote Programmer Callback: If programmed, when the remote programmer tries to initiate a session with the panel, the panel will hang up and call the remote programmer phone number.

- Ensures the correct remote programmer is initiating the call.

•Dial Pulse on all Phone Numbers: If programmed, the panel will dial phone number 1, 2, and the remote programmer phone number 3 using the pulse format.

•Dial Tone on all Phone Numbers: If programmed, the panel will dial phone number 1, 2, and the remote programmer phone number 3 using the tone format.

6.15Phone Answering Programming

•Answering Machine Bypass: This feature allows the panel to answer incoming calls when answering machines are used. If the line rings, stops ringing, then rings again within one minute, the panel will seize the phone line on the first ring.

•Phone Answering Programming: The panel can be programmed to answer the phone after a selected number of rings for remote programming access. It can also be programmed to answer the phone after a different number of rings when in armed or disarmed states.

-This can be used to call the panel location and determine its arming state.

Page 24 P/N: F01U035325-01 Copyright © 2007 Bosch Security Systems, Inc. DS7400Xi (4+) Reference Guide