Bosch Appliances DS7400XI, DS7445I Output Function Programming Program Addresses, Select Option

10.37 Output Function Programming: Program Addresses (2772-2843)

Output programming allows you to have the Outputs follow status events by partition or system-wide, or follow zone outputs in an Input/ Output Cross Matrix. See the Programming Addresses Worksheet (P/N: 43850) for a description of each address. See Glossary (section 6.4) for further details.

Select Option	DD	Data Digit 1 Options 1-9 and *1 are used to program an Output
		Function to follow status events for individual partitions.

Latch ON after Zone Alarm	0	Data Digit 1 Option *0 is used to program an Output
ON during Entry Pre-Alert	1	Function to follow the Wireless Keyfob Output Buttons.
		Data Digit 1 Option *2 is used to program an Output
ON when system is armed	3	Function to follow status events system-wide.

Zone alarm

6

Data Digit 1 Options *3-*5 are used to program an Output

Function to follow a zone or two zones in an Input/Output

Zone Alarm delayed by 20 sec.

7

Cross Matrix.

Data Digit

Program

Keypad Sounder output

8

Data Digit

1

2

Program

Address

Access output

(10 sec. pulse)

9

1

2

Address

1

Keyfob output

*0

1

Panic/Duress output**

*1

Follow System Status Event

*2

Data Digit

Option

RF3334

DD

Follow a single zone

*3

Follows

0

1

2

3

Disabled

0

Follow two zones-When EITHER zone changes state

*4

Moment

Option

Key

1

Disabled

Toggle

Option

Key

2

Follow two zones-When BOTH zones change state

*5

Burglar Alarm

Moment

3

Data Digit

*0-*5 are Hex values. They will

Fire Alarm

Toggle

4

1

2

display as A-F at the keypads.

*2

Program

Program

Program

DD

DD

Select Option

Select Option

Address

Address

Address

1

2

3

AC Power Failure

1

7

Radio Receiver Fault

Data Digit

Data Digit

Data Digit

Low Battery

2

8

Aux Power Fault

1

2

1

2

1

2

Communication Failure

3

9

Fire Trouble

System Fault**

4

*0

Supervisory

Keypad Supervision Fault

5

*1

Zone Trouble

Multiplex Bus Fault

6

*2

Duress PIN

*0 - *2 are Hex values. They will display as A - C at the keypads.

**System Faults include:
•	RAM fault			•	Serial Transmit fault																Enter the				Enter the
•	ROM fault			•	Serial Receive fault																Zone Number				Zone Number
•	Bell/Line Monitor fault (DS7420i) •				Aux. Relay fault																of First Zone				of Second
•	Line 1 fault			•	DS7416i Communications fault																to Follow				Zone to
•	Line 2 fault			•	RF Receiver Tamper																(see Zone				Follow
•	Bell fault			•	RF Receiver Jammed																HEX Values				(see Zone
•	Aux. Power fault			•	RF Receiver Trouble				Data Digit													chart)			HEX Values
•	Octal Relay fault			•	Printer Off-line																				chart)
									1	2
• Serial Module fault (DS7412)
									3																Not Required
														Data Digit											if following a
																									single zone
									Follows			0		1		2	3
	Output	Program	Program	Program
	Function	Address	Address	Address				Disabled
	Number
	1	2772	2773	2774				Armed Full
	2	2775	2776	2777
	3	2778	2779	2780				Armed Partial
	4	2781	2782	2783
	5	2784	2785	2876				Armed Any
	6	2787	2788	2789
	7	2790	2791	2792															Enter Data Digit as a:
	8	2793	2794	2795
	9	2796	2797	2798			Activate:				0		1		2		3	4		5	6	7	8	9	*0	*1	*2
	10	2799	2800	2801
	11	2802	2803	2804			Disabled
	12	2805	2806	2807
	13	2808	2809	2810			When zone is shorted
	14	2811	2812	2813
	15	2814	2815	2816			When Zone is opened
	16	2817	2818	2819
	17	2820	2821	2822			When panel is Armed
	18	2823	2824	2825
	19	2826	2827	2828			When panel is not Armed
	20	2829	2830	2831
	21	2832	2833	2834			Latch when activated**
	22	2835	2836	2837
	23	2838	2839	2840		** = This is only for DS7465 Outputs. DS7488 Outputs will not latch when this is selected.
	24	2841	2842	2843

Page 66 P/N: F01U035325-01 Copyright © 2007 Bosch Security Systems, Inc. DS7400Xi (4+) Reference Guide