Skil HD5860 manual Maintenance, Cleaning

Page 12
OIL
PLUG
OIL
LEVEL

SM 1619X01359 02-06 2/16/06 1:50 PM Page 12

Maintenance

Service

Preventive maintenance

!WARNING performed by unauthorized personnel may result in misplacing of internal wires and components which could cause serious hazard. We recommend that all tool service be performed by a Skil Factory Service Center or Authorized Skil Service Station.

TOOL LUBRICATION

Your Skil tool has been properly lubricated and is ready to use. However it is recommended that the gears be relubricated only with Skil lubricants: No. 80111 (8 oz. tube), No. 80112 (pint) or No. 80113 (1/2 gal. can).

Always check the oil level before using the saw. To check and add oil: Remove plug from power source and

place the saw’s foot on a horizontal surface. Remove oil plug using the same wrench used to remove the saw blade. The oil level should never be below bottom threads in the housing. When adding oil, fill until oil starts to run out of oil hole at arrow on housing and replace oil plug.

NOTE: If oil is extra dirty or thick, replace the plug and run the saw for one minute to warm up the oil. Then remove oil plug and turn saw upside down, to remove all oil. Fill housing with kerosene. Replace plug and run for one minute to flush out the gear housing. Drain out the kerosene and add fresh Skil lubricant. With a new saw, change the oil after the first ten hours of use.

CARBON BRUSHES

The brushes and commutator in your tool have been engineered for many hours of dependable service. To maintain peak efficiency of the motor, we recommend every two to six months the brushes be examined. The brushes should be free from dust and dirt. Brushes should be replaced when they have worn down to 3/16" in length. The brushes should slide freely in and out of the holders without sticking.

To check brushes: Disconnect plug from power source. Unscrew the brush caps on the

motor housing and lift out the brushes; note which way they face, so that the brushes can be returned to their original position. Clean the brush holder openings with compressed air or a clean cloth and replace the brushes and caps.

Only genuine Skil replacement brushes specially designed for your tool should be used.

BEARINGS

After about 300-400 hours of operation, or at every second brush change, the bearings should be replaced at Skil Factory Service Center or Authorized Skil Service Station. Bearings which become noisy (due to heavy load or very abrasive material cutting) should be replaced at once to avoid overheating or motor failure.

Cleaning

!WARNING To avoid accidents always disconnect the tool from

the power supply before cleaning or performing any maintenance. The tool may be cleaned most effectively with compressed dry air. Always wear safety goggles when cleaning tools with compressed air.

Ventilation openings and switch levers must be kept clean and free of foreign matter. Do not attempt to clean by inserting pointed objects through openings.

!CAUTION Certain cleaning agents and solvents damage

plastic parts. Some of these are: gasoline, carbon tetrachloride, chlorinated cleaning solvents, ammonia and household detergents that contain ammonia.

CARE OF BLADES

Blades become dull even from cutting regular lumber. If you find yourself forcing the saw forward to cut instead of just guiding it through the cut, chances are the blade is dull or coated with wood pitch.

When cleaning gum and wood pitch from blade, unplug the saw and remove the blade. Remember, blades are designed to cut, so handle carefully. Wipe the blade with kerosene or similar solvent to remove the gum and pitch. Unless you are experienced in sharpening blades, we recommend you do not try.

-12-

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Read Before Using ImportanteSee Voir Ver la página Power Tool Safety Rules Electrical SafetyPersonal Safety Keep your work area clean and well litSafety Rules for Circular Saws ServiceTool Use and Care Causes and Operator Prevention Kickback VARI-TORQUE ClutchProtruding blade may cut objects that can cause Kickback Symbols Functional Description and Specifications Quadrant Depth Adjustment FootCircular Saw Maximum CapacitiesAssembly Attaching the BladeVARI-TORQUE Clutch Depth Adjustment Bevel AdjustmentOperating Instructions Cutting Angle CheckSwitch General CutsCutting MASONRY/METAL Pocket CutsCutting Large Sheets RIP CutsRIP Board Guide Maintenance CleaningAccessories Tool’sRègles de Sécurité Générales Aire de travailSécurité des personnes Sécurité électrique Conservez CES InstructionsConsignes de sécurité pour scies circulaires Utilisation et entretien des outilsRéparation La réparation des outils électriques doit être confiéeCauses ET PRÉVENTION, PAR Lopérateur DU Rebond Ebon Embrayage VARI-TORQUELe plomb provenant des peintures à base de plomb Symboles Description fonctionnelle et spécifications Scie circulaireCapacités maximales Levier DE Réglage DE LA Profondeur SemelleAssemblage Montage DE LA LameEmbrayage « VARI-TORQUE » Consignes de fonctionnement Réglage DE LA Profondeur DE CoupeVérification DE L’ANGLE DE Coupe Réglage DE LA Coupe EN BiseauInterrupteur Coupes RégulierèsSciage DES Matériaux DE Maçonnerie ET DES Métaux Coupes EN GuichetCoupe DE Grandes Feuilles Coupes DE RefenteUtilisation D’UNE Planche Comme Guide DE Refente Entretien Lubrification DE L’OUTILBalais DE Charbon PaliersAccessoires Normas de seguridad para herramientas mecánicas Area de trabajoSeguridad eléctrica Seguridad personalNormas de seguridad para sierras circulares ServicioCausas DEL Retroceso Y SU Prevencion POR EL Operador Embrague DE PAR Motor VariableSM 1619X01359 02-06 2/16/06 150 PM Símbolos De Ni-CdDescripción funcional y especificaciones Sierra circularCapacidades máximas Ensamblaje Colocacion DE LA HojaEmbrague DE PAR Motor Variable Instrucciones de funcionamiento Ajuste DE ProfundidadAjuste DE Inclinación Guía DE LíneaGuía DE Interruptor Cortes GeneralesMovimiento libre del protector inferior Corte DE Mamposteria Y MetalCorte DE Planchas Grandes Cortes AL HiloTABLERO-GUIA Para Cortar AL Hilo Mantenimiento LimpiezaAccesorios CapacidadSM 1619X01359 02-06 2/16/06 150 PM Remarques Notas Limited Warranty of Skil HD Heavy Duty Portable Power Tools

HD5860 specifications

The Skil HD5860 is a powerful and versatile tool designed for both professional and amateur woodworkers. This heavy-duty saw is renowned for its exceptional performance, precision, and advanced features, making it a must-have for anyone looking to take their woodworking projects to the next level.

One of the standout features of the HD5860 is its robust 14-amp motor, which delivers fast and efficient cutting power. With the ability to reach speeds of up to 5,300 RPM, this saw can easily tackle a variety of materials, including hardwood, softwood, and engineered lumber. Its high-speed performance ensures clean cuts with minimal effort, allowing users to take on even the most challenging projects.

The Skil HD5860 is equipped with a lightweight aluminum base that enhances stability and reduces vibration during operation. This design feature not only improves accuracy but also extends the overall lifespan of the tool. The adjustable bevel angle, which can be set up to 45 degrees, adds versatility, enabling users to make angled cuts effortlessly. Whether you're cross-cutting or making compound angles, this saw provides the flexibility needed for a wide range of applications.

In terms of safety, the HD5860 includes several important features designed to protect the user during operation. The blade guard ensures safe cutting by covering the blade when not in use, while the electric brake stops the blade quickly once the trigger is released. Additionally, the onboard dust port helps maintain a cleaner workspace by connecting to a vacuum system, reducing dust and debris accumulation during cutting.

Another key characteristic is the laser guide system, which projects a line onto the workpiece, allowing for precise alignment and cuts. This feature significantly enhances accuracy, making it easier to follow cutting lines without second-guessing. The saw also comes with a durable carbide-tipped blade, ensuring long-lasting performance and cutting efficiency.

Overall, the Skil HD5860 combines power, precision, and safety in one tool, making it an excellent choice for woodworkers of all skill levels. With its advanced features and reliable performance, this saw is a valuable addition to any workshop, enabling users to achieve professional-quality results with ease. Whether you're undertaking a detailed woodworking project or simply need to make quick cuts, the Skil HD5860 proves to be a dependable partner in your woodworking endeavors.
Top Page Image Contents