Skil HD5860 manual Power Tool Safety Rules, Work Area, Electrical Safety, Personal Safety

Page 2

SM 1619X01359 02-06 2/16/06 1:50 PM Page 2

 

 

Power Tool Safety Rules

 

 

Read and understand all instructions. Failure to follow all instructions listed

 

! WARNING

 

 

below, may result in electric shock, fire and/or serious personal injury.

 

 

 

 

SAVE THESE INSTRUCTIONS

Work Area

Keep your work area clean and well lit.

Cluttered benches and dark areas invite accidents.

Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust. Power tools create sparks which may ignite the dust or fumes.

Keep by-standers, children, and visitors away while operating a power tool. Distractions can cause you to lose control.

Do not abuse the cord. Never use the cord to carry the tools or pull the plug from an outlet. Keep cord away from heat, oil, sharp edges or moving parts. Replace damaged cords immediately. Damaged cords increase the risk of electric shock.

When operating a power tool outside, use an outdoor extension cord marked "W-A" or "W." These cords are rated for outdoor use and reduce the risk of electric shock. Refer to “Recommended sizes of Extension Cords” in the Accessory section of this manual.

Electrical Safety

Grounded tools must be plugged into an outlet properly installed and grounded in accordance with all codes and ordinances. Never remove the grounding prong or modify the plug in any way. Do not use any adaptor plugs. Check with a qualified electrician if you are in doubt as to whether the outlet is properly grounded. If the tools should electrically malfunction or break down, grounding provides a low resistance path to carry electricity away from the user. Improper grounding can shock, burn or electrocute. Grounded tools are equipped with three conductor cord and three prong type plugs. Before plugging in the tool be certain the outlet voltage supplied is within the voltage marked on the nameplate. Do not use “AC only” rated tools with a DC power supply.

Avoid body contact with grounded surfaces such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is grounded. If operating the power tool in damp locations is unavoidable, a Ground Fault Circuit Interrupter must be used to supply the power to your tool. Electrician’s rubber gloves and footwear will further enhance your personal safety.

Don't expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.

Personal Safety

Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use tool while tired or under the influence of drugs, alcohol, or medication. A moment of inattention while operating power tools may result in serious personal injury.

Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep your hair, clothing, and gloves away from moving parts. Loose clothes, jewelry, or long hair can be caught in moving parts. Keep handles dry, clean and free from oil and grease.

Avoid accidental starting. Be sure switch is “OFF” before plugging in. Carrying tools with your finger on the switch or plugging in tools that have the switch “ON” invites accidents.

Remove adjusting keys or wrenches before turning the tool “ON”. A wrench or a key that is left attached to a rotating part of the tool may result in personal injury.

Do not overreach. Keep proper footing and balance at all times. Proper footing and balance enables better control of the tool in unexpected situations.

Use safety equipment. Always wear eye protection. Dust mask, non-skid safety shoes, hard hat, or hearing protection must be used for appropriate conditions.

-2-

Image 2
Contents See Voir Ver la página Read Before UsingImportante Personal Safety Power Tool Safety RulesElectrical Safety Keep your work area clean and well litTool Use and Care Safety Rules for Circular SawsService Causes and Operator Prevention Kickback VARI-TORQUE ClutchProtruding blade may cut objects that can cause Kickback Symbols Circular Saw Functional Description and SpecificationsQuadrant Depth Adjustment Foot Maximum CapacitiesVARI-TORQUE Clutch AssemblyAttaching the Blade Operating Instructions Depth AdjustmentBevel Adjustment Cutting Angle CheckCutting MASONRY/METAL SwitchGeneral Cuts Pocket CutsRIP Board Guide Cutting Large SheetsRIP Cuts Maintenance CleaningAccessories Tool’sSécurité des personnes Sécurité électrique Règles de Sécurité GénéralesAire de travail Conservez CES InstructionsRéparation Consignes de sécurité pour scies circulairesUtilisation et entretien des outils La réparation des outils électriques doit être confiéeCauses ET PRÉVENTION, PAR Lopérateur DU Rebond Ebon Embrayage VARI-TORQUELe plomb provenant des peintures à base de plomb Symboles Capacités maximales Description fonctionnelle et spécificationsScie circulaire Levier DE Réglage DE LA Profondeur SemelleEmbrayage « VARI-TORQUE » AssemblageMontage DE LA Lame Vérification DE L’ANGLE DE Coupe Consignes de fonctionnementRéglage DE LA Profondeur DE Coupe Réglage DE LA Coupe EN BiseauSciage DES Matériaux DE Maçonnerie ET DES Métaux InterrupteurCoupes Régulierès Coupes EN GuichetUtilisation D’UNE Planche Comme Guide DE Refente Coupe DE Grandes FeuillesCoupes DE Refente Balais DE Charbon EntretienLubrification DE L’OUTIL PaliersAccessoires Seguridad eléctrica Normas de seguridad para herramientas mecánicasArea de trabajo Seguridad personalNormas de seguridad para sierras circulares ServicioCausas DEL Retroceso Y SU Prevencion POR EL Operador Embrague DE PAR Motor VariableSM 1619X01359 02-06 2/16/06 150 PM Símbolos De Ni-CdCapacidades máximas Descripción funcional y especificacionesSierra circular Embrague DE PAR Motor Variable EnsamblajeColocacion DE LA Hoja Ajuste DE Inclinación Instrucciones de funcionamientoAjuste DE Profundidad Guía DE LíneaMovimiento libre del protector inferior Guía DE InterruptorCortes Generales Corte DE Mamposteria Y MetalTABLERO-GUIA Para Cortar AL Hilo Corte DE Planchas GrandesCortes AL Hilo Mantenimiento LimpiezaAccesorios CapacidadSM 1619X01359 02-06 2/16/06 150 PM Remarques Notas Limited Warranty of Skil HD Heavy Duty Portable Power Tools

HD5860 specifications

The Skil HD5860 is a powerful and versatile tool designed for both professional and amateur woodworkers. This heavy-duty saw is renowned for its exceptional performance, precision, and advanced features, making it a must-have for anyone looking to take their woodworking projects to the next level.

One of the standout features of the HD5860 is its robust 14-amp motor, which delivers fast and efficient cutting power. With the ability to reach speeds of up to 5,300 RPM, this saw can easily tackle a variety of materials, including hardwood, softwood, and engineered lumber. Its high-speed performance ensures clean cuts with minimal effort, allowing users to take on even the most challenging projects.

The Skil HD5860 is equipped with a lightweight aluminum base that enhances stability and reduces vibration during operation. This design feature not only improves accuracy but also extends the overall lifespan of the tool. The adjustable bevel angle, which can be set up to 45 degrees, adds versatility, enabling users to make angled cuts effortlessly. Whether you're cross-cutting or making compound angles, this saw provides the flexibility needed for a wide range of applications.

In terms of safety, the HD5860 includes several important features designed to protect the user during operation. The blade guard ensures safe cutting by covering the blade when not in use, while the electric brake stops the blade quickly once the trigger is released. Additionally, the onboard dust port helps maintain a cleaner workspace by connecting to a vacuum system, reducing dust and debris accumulation during cutting.

Another key characteristic is the laser guide system, which projects a line onto the workpiece, allowing for precise alignment and cuts. This feature significantly enhances accuracy, making it easier to follow cutting lines without second-guessing. The saw also comes with a durable carbide-tipped blade, ensuring long-lasting performance and cutting efficiency.

Overall, the Skil HD5860 combines power, precision, and safety in one tool, making it an excellent choice for woodworkers of all skill levels. With its advanced features and reliable performance, this saw is a valuable addition to any workshop, enabling users to achieve professional-quality results with ease. Whether you're undertaking a detailed woodworking project or simply need to make quick cuts, the Skil HD5860 proves to be a dependable partner in your woodworking endeavors.