INSTALL VOLCANIC STONE, GLOWING EMBERS AND LOGS
1.Remove the front glass enclosure panel (see Removing Glass Enclosure Panels on Page 6 ).
2.Remove log set box from firebox. Next, remove embers and vermiculite from control compartment. Handle logs carefully to pre- vent breakage.
3.Install decorative volcanic stone - Sprinkle the decorative volcanic stone in a pleasing pat- tern (see Figure 6). The volcanic stone should be placed directly on top of the firebox bottom, along the slope and to the back at the right and left sides of the burner. Position any ceramic fiber liners before placing the stone. Logs can be positioned after the volcanic stone.
Volcanic Stone
Place Volcanaic
Stone As Shown
Figure 6
4.Placement of Glowing Embers - Separate the Embers (rockwool) into pieces about the size of a quarter (see Figure 7). Keep the pieces fluffed up, not matted. Distribute these pieces over the surface of the burner, as shown in Figures 8 & 9. Do not use more than is necessary. Ensure that the main burner slots remain uncovered by the ember material. Position the embers on the small holes of the ember bed area.
Glowing Embers
Separate into Quarter
Size (separate) Pieces
Bag of Glowing
Embers (rockwool)
Figure 7
Note: This appliance is provided with enough Glowing Embers for several applications, do not use all that is in a new bag at one time. For best glowing effect, replace the ember material annually.
5. Placement of Logs -
All logs that have locating notches or slots to help ensure that they are properly positioned. All top logs that rest on lower logs, do so over notches, indents or nubs. Proper log placement is critical to prevent sooting. Logs should be placed in the gaps between the flame peaks and should be positioned so they do not impinge the flames.
SLDVT-35 - Install the four logs as Follows
Carefully position the ceramic fiber logs over the burner as shown in Figure 8. Logs should be placed in the order shown and per the fol- lowing instructions.
1. Place the left front log (1) as shown. Posi- tion it on the two left front log brackets.
2. Place the right front log (2) as shown. Posi- tion it on the two right front log brackets.
3. Place the left rear log (3) as shown. Posi- tion it on the upper and lower left rear log brackets.
4. Place the right rear log (4) as shown. Posi- tion it on the right rear log bracket. Note that the hole on the bottom of the right rear log rests over the "Nub" on the right front log.
SLDVT-40 - Install the four logs as Follows
Carefully position the ceramic fiber logs and twigs over the burner as shown in Figure 9. Logs should be placed in the order shown and per the following instructions.
1. Place the ember chunk (1) over the tab on the rear log support as shown.
2. Place the left front log (2) as shown. Posi- tion it on the two left front log brackets.
3. Place the right front log (3) as shown. Posi- tion it on the two right front log brackets.
4. Place the left rear log (4) as shown. Position it on the left rear log bracket.
5. Place the right rear log (5) as shown. Posi- tion it on the right rear log bracket. Note that the hole on the bottom of the right rear log rests over the "Nub" on the right front log.
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
WARNING: DO NOT attempt to install the logs until the appliance installation has been completed, the gas line connected and tested for leaks and the initial burner operation has been checked out.
WARNING: The size and position of the log set was engineered to give the appliance a safe, reliable and attractive flame pattern. Any attempt to use a different log set in the fireplace will void the war- ranty and will result in incomplete combustion, sooting, and poor flame quality.
WARNING: This appliance is not designed to burn wood. Any attempt to do so could cause irrep- arable damage to appliance and prove hazardous to your safety.
WARNINGS: If logs are not installed according to the log installation instructions, flame impingement and improper com- bustion could occur and result in soot and/or excessive production of carbon monoxide (CO), a color- less, odorless, toxic gas.
REFERENCE
Firebox Accessories / Parts
Cat. No. | Model No. | Description | |
|
|
| |
88L53 | FGE | Bag of Glowing Embers | |
|
| (1 oz. rockwool) | |
|
|
| |
80L42 | FDVS | Bag of Decorative | |
Volcanic Stone | |||
|
| ||
|
|
|
Table 8