Guardian Technologies GGU350TT Belt replacement, Headlight replacement, Troubleshooting guide

Belt replacement

WARNING: Before replacing the belt, make sure the cleaner

is unplugged from the electrical outlet.

•Turn OFF the cleaner and unplug from electrical outlet.

•Remove the bottom plate of the base by removing the five (5) screws using a Phillips screwdriver. (Fig. 25)

•Set the new belt over motor pulley. (Fig. 26) Use replacement belt: BLT1.

•Slip the brush roll into the belt and reassemble. (Fig. 27)

•Replace the bottom plate and secure the 5 screws.

Motor Pulley

Fig. 25 Fig. 26 Fig. 27

headlight replacement

WARNING: Before replacing the headlight, make sure the cleaner

is unplugged from the electrical outlet.

•Turn OFF the cleaner and unplug from electrical outlet.

•Press the handle release pedal and use the handle to place the body in a flat position.

•Remove the headlight cover by removing the screw with a Phillips screwdriver. (Fig. 28)

•Pull the bulb straight out of the socket. (Fig. 29)

•Install the new bulb, model LBU.

•Replace the headlight cover and secure the screw.

Headlight

CoverHeadlight

Fig. 28 Fig. 29

NOTE: Replacement parts can be purchased by calling 1.866.603.5900 or by visiting www.germguardian.com.

E-12

troubleshooting guide

Please check each item below if you have trouble with your vacuum.

Before checking, always ensure that the vacuum is unplugged from the power supply.

PROBLEM	PROBLEM		SOLUTION
Vacuum won't run.	1.	Power cord not firmly plugged	1.	Plug in unit firmly.
		into the outlet.
	2.	Motor protector tripped.	2.	Cool down and press the RESET button.
				(See page 3)
	3.	Needs service.	3.	Take to service center or call 1.866.603.5900.
Brush roll won't spin.	1.	Vacuum is not in the	1.	The brush only turns on when the handle is
		UPRIGHT mode.		released for vacuuming. The brush does not come
				on in the UPRIGHT position even if the switch is
				ON. Depress handle for brushroll to start turning.
	2.	Brush switch is OFF.	2.	Make sure the brush switch is ON.
	3.	Brush roll is jammed.	3.	Remove it and clean debris, hair, etc. off of
				brush, then replace.
	4.	Belt is broken or off	4.	Replace the new belt or correct the belt's securing.
		motor pulley.		(See page 11)
Vacuum or tool won't	1.	Incorrect height setting.	1.	Rotate height adjustment knob to correct height
pick up dirt.				setting. (See page 6)
	2.	Hose not attached to:	2A. Check hose connection and make sure it is
		A. Inlet		attached to proper inlet: base inlet on body
		B. Base.		(UPRIGHT) or inlet on handle (CANISTER/TOOLS).
			2B. Grasp hose tube and firmly push onto base.
	3.	Clogged hose.	3.	Try to remove clog by squeezing out of hose.
	4.	Dirt cup is full.	4.	Empty dirt cup (see page 9); if washed, after
				dried well, reinsert it.
	5.	Inner filter is blocked.	5.	Clean or replace with new. (See page 10)
	6.	Crack or hole in hose.	6.	Take to service center or call 1.866.603.5900.
Vacuum is difficult	1.	Incorrect height setting.	1.	Rotate height adjustment knob to correct height
to push.				setting. (See page 6)
	2.	Brush switch is OFF.	2.	Make sure the brush switch is ON.
Visible dust escaping	1.	Dirt cup is full.	1.	Empty dirt cup (see page 9); wash it, after dried
from vacuum.				well, replace it.
	2.	Filter missing or incorrectly	2.	Check inner filter and exhaust filter for
		installed.		correct installation.
	3.	Dirt cup installed incorrectly.	3.	Pull out and re-insert dirt cup correctly.
				E-13