First Alert FA168CPS Installer Code, Quick ARM Enable, RF JAM Option, Zone Sounds and Timing 31

ALARM SOUNDER (BELL) TIMEOUT

EXIT DELAY

ENTRY DELAY #1 (zone type 01)

ENTRY DELAY #2 (zone type 02)

AUDIBLE EXIT WARNING CONFIRMATION OF ARMING DING

FIRE ALARMSOUNDER TIMEOUT

352*5$00,1*￿)250￿￿

Entries apply to both the FA168CPS and FA148CP controls, except entries shown in dashed boxes, which apply only to the FA168CPS (partition entries) and are not applicable to the FA148CP.

Entry of a number other than one specified will give unpredictable results. Values shown in brackets are factory defaults.

Field	Function	Data Entries		Programmable Values
SYSTEM SETUP (✱20–✱29)
✱ 20	INSTALLER CODE				4 digits, 0–9
			[4112]
✱21	QUICK ARM ENABLE	[0,0]			0 = no; 1 = yes
		Part. 1 Part.2
✱22	RF JAM OPTION	[0]			0 = no RF Jam detection; 1 = send RF Jam report
					UL: must be 1 if wireless devices are used

✱23 QUICK (FORCED) BYPASS

✱24 RF HOUSE ID CODE

✱26 CHIME BY ZONE

✱27 POWERLINE CARRIER DEVICE (X–10)

HOUSE CODE

✱28 ACCESS CODE FOR PHONE MODULE

✱29 LONG RANGE RADIO OUTPUT

ZONE SOUNDS AND TIMING (✱31 – ✱39)

✱31 SINGLE ALARM SOUNDING per ZONE ✱32

✱33

[0,0]

Part. 1 Part. 2

Part. 1 Part. 2 Common

[0]

[0]

[00]

(Partition 1 only)

[0]

[0]

[0]

[1]

0 = no quick bypass UL: must be “0”

1 = allow quick bypass (code + [6] + [#] )

00 = disable all wireless keypad usage

01–31 = using 5827, 5827BD or 5804BD keypad [00,00,00]

0 = no; 1 = yes (select zones to chime on zone list 3, using *81 Menu mode)

0 = A; 1 = B, 2 = C, 3 = D, 4 = E, 5 = F, 6 = G,

7 = H, 8 = I, 9 = J, #10 = K, #11 = L, #12 = M, #13 = N, #14 = O, #15 = P UL: not for fire or UL installations

00 = disable; 1st digit: enter 1–9; 2nd digit: enter # + 11 for "✱", or # + 12 for "#".

UL: must be “00” for UL Commercial Burg. installations

0 = disable; 1 = enable

0 = no UL: must be “0”; 1 = yes

0 = sounder stops at timeout;

1 = no sounder timeout UL: must be “1” for fire install.

0 = none; 1 = 4 min; 2 = 8 min; 3 =12 min; 4 = 16 min;

UL: For residential fire alarm installation, must be set for a minimum of 4 min (option 1); for UL Commercial Burglary installations, must be minimum 16 min (option 4)

✱34

✱35

		[60,60]
Part. 1	Part. 2
		[30,30]
Part. 1	Part. 2

Common zones use same delay as partition 1.

00 - 96 = 0 - 96 secs; 97 = 120 secs

SIA Installations: minimum exit delay is 45 seconds

UL: see inst. instr. for requirements.

Common zones use same delay as partition 1.

00	- 96 = 0 - 96 seconds
97	= 120 seconds	SIA Installations:
98	= 180 seconds	minimum entry delay is
99	= 240 seconds	30 seconds

For UL Residential Burglary Alarm installations, must be set for a maximum of 30 seconds; entry delay plus dial delay should not exceed 1 min. For UL Commercial Burglar Alarm, total entry delay may not exceed 45 seconds.

✱36

∗37

		[30,30]
Part. 1	Part. 2

[1,1]

See *35 Entry Delay 1 above for entries.

0 = no; 1 = yes

SIA Installations: must be enabled (enter 1)

✱38

[0,0]	0	= no; 1 = yes (wired keypads and RF)
	2	= yes, RF only

Part. 1 Part. 2

✱39 POWER UP IN PREVIOUS STATE [1]

DIALER PROGRAMMING (✱40 – ✱42)

UL: must be “1” for UL Commercial Burglar Alarm inst.

0 = no; 1 = yes UL: must be “1”

Do not fill unused spaces. Enter 0–9; #+11 for '✱'; #+12 for '#'; #+13 for a 2-second pause. If fewer than the maximum digits entered, exit the field by pressing [✶]. The next data field number is displayed.

✱40 PABX ACCESS CODE

Enter up to 6 digits. To clear entries, press ✱40✱. If call waiting

used, enter “∗ (#+11) 70” plus “# + 13” (pause).

✱ 41	PRIMARY PHONE No.
✱ 42	SECOND PHONE No.

Enter up to 20 digits. To clear entries, press ✱41✱ or ✱42✱ respectively.

– 3 –